Summary of Contents for Camsat CDS-5IP
- Page 1 WIRELESS TRANSMISSION SYSTEM FOR IP HD CAMERA EXTERNAL TRANSMITTING-RECEIVING UNIT CDS-5IP Quick Installation Guide...
- Page 2 About the Quick Installation Guide This Quick Installation Guide is intended to guide professional installer to install the CDS-5IP. It covers procedures to assist you in avoiding unforeseen problems. Conventions Warning: This sign indicates a warning or caution that you have to abide.
-
Page 3: Chapter 1 Introduction
Chapter 1 Introduction Introduction CDS-5IP is a wireless transmission system designed to transmit audio / video in the 5GHz frequency band power of 1W (30dbi). The device transmits signals from IP cameras with high resolution (up to 5Mpixels). Built-in dual antenna 5GHz MIMO 2 x 16dBi allows signal transmission as standard to 2km, and the possibility of using fine-tuning function of the antenna provides high transmission quality even at varying distances. -
Page 4: Product Package
Product Package The product package you have received should contain the following items. If any of them are not included or damaged, please contact your local vendor for support. ×1 CDS-5IP - Wireless External Video Unit ×2 Pole Mounting Ring ×1 Power Cord &... -
Page 5: Chapter 2 Preparation Before Installation
To keep you safe and install the hardware properly, please read and follow these safety precautions. If you are installing the CDS-5IP - Wireless External Unit for the first time, for your safety as well as others’, please seek assistance from a professional installer who has received safety training on the hazards involved. -
Page 6: Installation Precautions
Installation Precautions To keep the CDS-5IP - Wireless External Unit well while you are installing it, please read and follow these installation precautions. Users MUST use a proper and well-installed grounding and surge arrestor with the Wireless External Video Unit; otherwise, a random lightening could easily cause fatal damage to the unit. -
Page 7: Chapter 3 System Installation
Chapter 3 System Installation Connect up The bottom of CDS-5IP - Wireless External Video Unit is a movable cover. Loosen the screw with a Philips screwdriver. Grab the cover and pull it back harder to take it out as the figure shown below. - Page 8 The secondary Ethernet port (labeled LAN 2) is for IP camera or next CDS-5IP Unit video integration. To use it you need to enable the secondary port in advance before connecting with the IP camera from the CDS-5IP`s Web Management as shown below.
- Page 9 Press the black PWR button beside the LAN 1 Ethernet port. Attach and fasten the removable cover to the bottom of the unit with the screw. Power on the CDS-5IP - Wireless External Video Unit by plugging the power adapter to the power socket.
-
Page 10: Using The External Antenna
Using the External Antenna The CDS-5IP - Wireless External Video Unit provides two reverse SMA antenna connectors if you prefer to use the external antenna for your application instead of the built-in directional antenna, please follow the steps below. Remove the two plugs as circled below: Connect your external antenna to the SMA-type connectors at the bottom of the Wireless External Video Unit. -
Page 11: Pole Mounting
CDS-5IP as the following right picture shows. Figure 5 Pole Mounting – Step 1 Mount the CDS-5IP - Wireless External Video Unit steadily to the pole by locking the pole mounting ring tightly. The mounting ring supports pole diameter 32mm to 70mm. -
Page 12: Chapter 4 Configuration
Connect the CDS-5IPwith your PC by an Ethernet cable plugging in LAN port of POE injector in one side and in LAN port of PC in the other side. Power on the CDS-5IP by POE from the supplied POE injector and press the black power button beside the LAN1 port. - Page 13 Now, you will see the log-in page of the CDS-5IP. The default Name and Password are “camsat” and “camsat” respectively. Enter the password and then click Login. We’ll elaborate the CDS-5IP - Wireless External Video Unit factory default settings. You can re-acquire these parameters by default.
- Page 14 Open System Encryption None Wireless Separation Disable Access Control Disable For users who use the CDS-5IP - Wireless External Video Unit for the first time, it is recommended that you begin configuration from “Basic Settings” in “System” shown below: Page 14...
- Page 15 TCP/IP Settings Open “TCP/IP Settings” in “System” as below to configure the parameters for LAN which connects to the LAN port of the CDS-5IP. In this page, users may change the settings for IP Address, Subnet Mask, and DHCP Server.
- Page 16 Video Bridge Mode 1. Open “Basic Settings” in “Wireless”. From Wireless Mode, select “Video Bridge” and click “Apply” to save settings. 2. Go to “WDS Settings ” in “Wireless”, input the MAC address of the remote bridge to “Remote AP MAC Address 1” field and click “Apply”; Page 16...
- Page 17 WDS peer of MASTER2 in any case). Mesh and Ring network topologies are not supported by WDS and should be avoided in all the use cases. 3. Repeat the above procedures to configure the remote CDS-5IP. 4. Use ping to check whether the link between the two bridges is OK.
- Page 18 Wait about 5 seconds, the antenna alignment starts and performs alignment every one second. Fix the local antenna and adjust the remote antenna elevation and horizontal direction. During the adjustment, observe “Current RSSI” and “Signal Strength” in local bridge. The value will refresh every 1 second. Fix the remote antenna when it reaches your expectation.
- Page 19 “SMA Connector” after your external antennas are physically installed. Warning: Do not switch from built-in antenna to the external antenna from WEB management without physically attaching the external antenna onto the CDS-5IP; otherwise, damage might be caused to the device itself. Page 19...
- Page 20 “Apply”. Note: For longer transmission of the CDS-5IP, you may also use an external antenna; if so, remember to set the antenna setting from “Internal (16 dBi)” to “SMA Connector” after your external antenna is successfully installed.
- Page 21 Click the “Site Survey” button beside SLAVE Mode. It will scan all the available CDS-5IP within coverage. Select the one you prefer to connect to, and click Selected to establish the connection. 3. If the MASTER you connect to require authentication or encryption keys, click Profile Settings in the left column, fill out the corresponding items, and click “...
- Page 22 Apply to save it. Feel free to change the other parameters to optimize your application before clicking Apply. Note: For longer transmission of the CDS-5IP, you may also use an external antenna; if so, remember to set the antenna setting from “Internal (16 dBi)” to “SMA Connector” after your external antenna is successfully...
- Page 23 Video Bridge Mode. To connect the wireless client to the MASTER, please follow the procedures described in SLAVE Mode. Congratulations! You have primarily completed configuration on the CDS-5IP and they can be put into operation. For more advanced configurations, please refer to the User manual.
- Page 24 General terms and conditions of a warranty Camsat company gives a warranty of 24 months for transmission sets of the following series: TCO 5807, CAM 5816, CDS 5021, CD04, CD06, CDS-5IP 1. In case of detecting incorrect work of a device, before giving the device to the service, it is necessary to make sure that everything was done in accordance with the instruction manual.
Need help?
Do you have a question about the CDS-5IP and is the answer not in the manual?
Questions and answers