Advertisement
The Service LED flashes yellow when any of the following events occur: ActiveX Blocked, ActiveX or Java archive access denied, Cookie Removed, Fragmented Packet Blocked, IP Spoof Detected, Java Blocked, Land Attack Dropped, Newsgroup Accessed, Newsgroup Blocked, Ping of Death Blocked, Proxy Access Blocked, Smurf Amplification Dropped, TCP SYN/FIN Packet Dropped, TCP Xmas Tree Packet Dropped, Unauthorized TCP Packet Denied, Unauthorized UDP Packet Denied, Unauthorized ICMP Packet Denied, Website Accessed, Website Blocked.
Verify that your package has the following contents:
NOTE: The included power cord is approved for use only in specific countries or regions. Before using a power cord, verify that it is rated and approved for use in your location.
Your SonicWall appliance is Zero-Touch enabled.
Zero-Touch makes it easy to register your unit and add it to Capture Security Center for management and reporting in 3 simple steps.
For information about using Zero-Touch, see the Zero-Touch Deployment Guide on the Support portal.
After completing the Zero-Touch deployment process, you can skip to Mounting the TZ Appliance in this guide. For non Zero-Touch deployments, continue with the next section.
Only use the included power adapter with this appliance. Do not use a power adapter that is damaged or from another appliance.
TIP: Your computer should be using DHCP IP addressing.
NOTE: The default administrator credentials are Username: admin
Password: password
NOTE: For manual configuration, refer to the latest SonicOS Quick Configuration administration documentation.
Registration is an important part of the setup process and is necessary in order to receive the benefits of SonicWall security services, firmware updates, and technical support.
To register the appliance from SonicOS:
TIP: Registering the appliance from SonicOS requires that DNS Server settings are configured on the WAN (X1) interface.
You are asked to select a country code when using the Wireless Guide or when you initially navigate to the Wireless > Settings page. Be sure to select the country code for the country in which the appliance will be deployed, even if you are not currently in that country.
When sold into USA list will be restricted to USA. When sold into Canada valid selection will be restricted to Canada.
Do not mount the appliance on the ceiling, it is not designed for secure ceiling mounting.
For optional wall mounting, you need:
To mount the appliance on the wall:
For your safety, follow all instructions listed in this section.
Install in a location away from direct sunlight and sources of heat. A maximum ambient temperature of 104º F (40º C) is recommended.
Route cables away from power lines, fluorescent lighting fixtures, and sources of noise such as radios, transmitters, and broadband amplifiers.
The included power cord(s) are approved for use only in specific countries or regions. Before using a power cord, verify that it is rated and approved for use in your location.
Ensure that no water or excessive moisture can enter the unit.
Allow unrestricted airflow around the unit and through the vents on the side of the unit. A minimum of 1 inch (25.44mm) clearance is recommended.
Consideration must be given to the connection of the equipment to the supply circuit. Appropriate consideration of equipment nameplate ratings must be used when addressing this concern. Do not overload the circuit.
This equipment is not intended for use at workplaces with visual display units, in accordance with §2 of the German ordinance for workplaces with visual display units. To avoid incommoding reflections at visual display workplaces this device must not be placed in the direct field of view.
The Lithium Battery used in the SonicWall security appliance may not be replaced by the user. Return the SonicWall security appliance to a SonicWall-authorized service center for replacement with the same or equivalent type recommended by the manufacturer. If, for any reason, the battery or SonicWall security appliance must be disposed of, do so following the battery manufacturer's instructions.
All Ethernet and RS232 (Console) cables are designed for intra-building connection to other equipment. Do not connect these ports directly to communication wiring or other wiring that exits the building where the SonicWall appliance is located.
If the power supply is missing from your SonicWall product package, please contact SonicWall Technical Support at https://support.sonicwall.com/contact-support for a replacement. This product should only be used with a UL listed power supply marked "I.T.E. LPS" with an output rated 12V DC, minimum 5.0 A, Tma: minimum 40 degree C.
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download SonicWALL TZ570, TZ570W - Firewalls Quick Start Guide
Advertisement
Need help?
Do you have a question about the TZ570 and is the answer not in the manual?
Questions and answers