HANYOUNG NUX PEN Series Instruction Manual page 2

PEN series
Photo Sensor
INSTRUCTION MANUAL
Thank you for purchasing Hanyoung Nux products.
Please read the instruction manual
carefully before using this product, and use the product correctly.
Also, please keep this instruction manual where you can see it any time.
▍ Safety information
Please read the safety information carefully then use the product correctly.
The alerts declared in the manual are classified into Danger, Warning and Caution according to their importance
DANGER Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury
WARNING Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury
CAUTION Indicates a potentially hazardous situation which, if not avoided, may result in minor injury or property damage
DANGER
• The input/output terminals are subject to electric shock risk.
Never let the input/output terminals come in contact with your body or conductive substances.
Warning
•Users must attach the safety device twice when using the product with the machines which may cause casualties, mass
damage to the assets or etc since it is not designed as the safety device.
•Please supply in the proper power supply voltage accordance to the rating in order to prevent the product from
breaking down or damage.
•Please detach the device after turning off the power. Not doing so may cause an electric shock, malfunction or
breaking the device
•Do not disassemble, manufacture, upgrade or fix the product. There are possibilities of malfunction or electric shock or
fire to occur.
Caution
•Please do not use auto-trans in order to maintain the safety of power supply voltage of the product.
Please use the insulation trans.
•When extending the cable, please use thick wire (at least thickness 0.3 ㎟) and at this moment, please watch out for the voltage-drop
•Please separately wire the high-tension wire/power line from the sensor.
•Turning the power ON/OFF continuously will shorten the life expectancy of the product or may cause the malfunction
so please be cautious
•When cleaning the lens and the case, please use a dry cloth and gently wipe the surface. You must not use solvents
such as thinner or alcohol.
•When setting the sensitivity, do not actuate the sensitivity volume with the strong force on it. Doing so may break the volume.
•When using the power supply device (SMPS), users must earth the frame ground (F.G) terminal.
Not doing so may cause malfunction due to the switching noise of the power so please be cautious
Power
Supply
(SMPS)
※Users must follow the safety information stated above to avoid product failure.
▍ Specification
Model
PEN-T10A
Detection method Through - beam
Detection range 10 m
Sensing object Opaque object above Ø20 ㎜
Power supply voltage
Power
transmitter 1 W max
consumption
receiver 2 W max
(current)
Operation mode Light ON / Dark ON ※ selected by the mode volume
Sensitivity adjustment -
Relay contact output (1c) 30 VDC 5 A / 250 VAC 5 A (resistive load)
Control output
Response time
Hysteresis
Light source
Indicator Output indication : Red LED (In case of the transmitter, red indicates the power state), Stability: Green LED
Ambient illumination Sunlight : 11,000 Lux max, Incandescent lamp : 3,000 Lux max
Ambient temperature During operation : -20 ~ 60 C, During storage : -25 ~ 70 C (Without condensation))
Ambient humidity
Degree of protection
Insulation resistance 20 ㏁ min (500 VDC mega between the recharging part and case)
Dielectric strength
Vibration resistance 10 – 55 ㎐ 1.5 ㎜ double amplitude for 2 hours each in X, Y and Z directions (but when power is OFF)
Shock resistance 500 ㎨ (Approx. 50 G), 3 times each in X, Y and Z directions
Connection method Cable extended type (# of cables : 5P, diameter : Ø 6 ㎜, length : 2 ㎜) ※ but transmitter is 2P
Material
weight(g)
Cautious 1) the sensing distance can be varied depending on the size, surface condition, glossy, non-glossy of the sensing object.
▍ Connection diagram
■ Through-beam type is limited to the receiver
HANYOUNGNUXCO.,LTD
28, Gilpa-ro 71beon-gil,
Michuhol-gu, Incheon, Korea
TEL : +82-32-876-4697
http://www.hynux.com
Photo
Sensor
C(0.01㎌-0.1㎌/500 V)
- Noise Eliminating
Condenser
Frame
Power built-in type
PEN-M5A
Retro - reflective Diffuse - reflective
0.1 ~ 5 m
Opaque object above Ø60 ㎜ White non-glossy paper 200 × 200 ㎜
24 - 240 VDC/AC (Dual usage) ±10 % 50/60 ㎐
2 W max
Built-in the sensitivity adjustment volume
Electrical life expectancy : min 100,000 times
20 ㎳ max
- Within the 20 % of the detection range
Infrared ray LED (850 ㎚)
35 ~ 85 % R.H. (Without condensation))
IP 64 (IEC)
1,500 VAC (50/60 ㎐ 1 minute)
Case : heat resistant ABS, Lens: PC
150
RELAY
BLACK - N.O
WHITE - COM
GRAY - N.C
BROWN
Power supply
24 - 240 V DC/AC
BLUE
Circuit
▍ Dimension
■ Outer dimension
MK1501KE190905
■ Bracket mounted
▍ Output operation characteristic
Output Indicator
(Red)
Control output
(RELAY/TR)
stability Indicator
(Green)
Output Indicator
(Red)
Control output
(RELAY/TR)
stability Indicator
(Green)
▍ Installation
■ Through-beam type
NO
Supply in the power after placing the transmitter
1
and receiver face to face each other.
Fix either the transmitter or receiver and check for the
range where the operation indicator becomes turned
2 ON or turned OFF by controlling in the direction of up,
PEN-R700A
down, left and right. After finishing the confirmation,
place it in the middle and fix it.
700 ㎜
Place the sensing object within the setting range and
3
confirm the condition of proper operation.
■ Retro-reflective type
NO
Supply in the power after placing the sensor and
1
mirror face to face each other in the straight line.
Fix either the sensor or mirror and check for the range
where the operation indicator becomes turned OFF by
2 controlling in the direction of up, down, left and right.
After finishing the confirmation, place it in the middle
Place the sensing object within the setting range and
3 confirm the condition of proper operation and once
the confirmation is finished, fix the sensor.
■ Diffuse-reflective type
NO
After removing the sensing object, turn sensitivity
volume gradually to the max direction and once
1 indicator lights up, that position will be referred as 'A'.
(If indicator does not get turned ON (OFF) even in the
position of maximum set on the max position.)
Place the sensing object in the desirable setting position
and gradually turn the sensitivity volume from 'A' to the
2
'min' direction and once the indicator gets to turned
ON (OFF) than that position will be referred as 'B'.
Place the sensitivity volume in the middle of max
3 and 'A' or 'B' and confirm the operation condition of
sensing object that occurs within the setting range.
■ Reflector (HY-M5)
LIGHT.ON operation
DARK. ON operation
Method
transmitter receiver
Method
transmitter receiver
transmitter
transmitter
transmitter
transmitter
and fix it.
transmitter
transmitter
Sensing object
Sensor
Method Picture
Max Sensitivit Volume
Sensing object
Sensing object Sensor
Sensor
Sensor
Sensing object
Sensor
Sensor
Picture Output mode
transmitter receiver
transmitter receiver
Dark ON
fixed
transmitter
Picture Output mode
Sensor
REFLECTOR
Sensing object
receiver
Sensor
Max Sensitivit Volume
REFLECTOR
Dark ON
receiver
Sensing object
Sensor
Sensor
REFLECTOR
transmitter
Sensing object
Sensor
transmitter
Sensitivity Volume Output mode
Max Sensitivit Volume
Sensing object
Light ON
Sensing object
Senso
transmitt
transmi
REFLEC
REFLE
REFLE