AnyTone BT01 - Bluetooth Microphone Manual

Introduction

Thank you for purchasing Anytone BT01 Bluetooth Microphone. This product uses a dedicated master-slave Bluetooth module to realize wireless talk and wireless operation settings for all functions of the AT- D578UV DMR mobile radio with built-in Bluetooth module. Combined with the noise reduction function, it can effectively reduce background noise and ambient noise to achieve high-definition intercom.

Precautions

Please read the following regulations carefully before using this product.
The following regulations will help you understand and fulfill your obligations in the warranty terms.

1. Without permission, please do not try to disassemble or modify the BT01 Bluetooth Microphone. The handling of the Bluetooth Microphone by non-professionals may cause damage.
2. Please don't put the Bluetooth Microphone in a dusty or damp place.
3. Please abide by the walkie-talkie usage rate of 1 minute for transmission and 4 minutes for reception. Long-term transmission or continuous use in high-power mode will cause the AT-D578UV mobile radio to heat up.
4. Please charge the BT01 Bluetooth Microphone before using it.
5. After the BT01 Bluetooth Microphone is turned on, it will automatically enter the pairing state. Before use, please turn on the Bluetooth function of the AT-D578UV mobile radio, and pair it with the BT01 Bluetooth microphone.

Accessories

Charge The Battery

Charging Instructions

1. Insert the USB plug of the charging cable into the power adapter.
2. Plug the power adapter into the AC power outlet.
3. Insert the other end of the charging cable into the charging/upgrade interface of the radio.
4. The red charging indicator of the BT01 Bluetooth Microphone is on.
5. When the red charging indicator of the BT01 Bluetooth microphone goes out, the charging is complete.

» USB Adaptor and Cigarette light charger must be 5v voltage and ≥1A current output.

Getting Started

Indicator Instructions

Basic Operation

Power ON

Press the top [POW] button on microphone, the right green indicator light on, later the screen displays "Select Port", press or to choose the connect mode:

BT MODE: Connect the BT01 microphone to AT-D578UV mobile radio through Bluetooth.

CABLE MODE: Connect the BT01 microphone to AT-D578UV mobile radio through 4m cable.

Click on "confirm" to select the connect mode.

BT MODE connect to AT-D578UV

After select "BT MODE" on microphone, it will display BT NAME and "NO DEVICE CONNECTED" when no radio is connected. In this state, the BT pairing shall be done on AT-D578UV.

1. Enter into AT-D578UV radio Menu Bluetooth BT On/Off, set it ON.
2. Switch to AT-D578UV radio Menu Bluetooth BT Pairing, select "Seek BT".
3. AT-D578UV radio displays "Seeking BT", it will take some time to do the pairing.
4. AT-D578UV radio displays "ALL DATA CHECKING", the display content of the AT-D578UV radio will be mapped to the Bluetooth microphone.
5. AT-D578UV radio displays "EXTERNAL BT MODE" on the screen, the pairing is done.

BT01 microphone is able to access the radio menu and do communications now.

» Once the BT pairing is done, the BT microphone will automatically connect to AT-D578UV radio after reboot.

CABLE MODE connect to AT-D578UV

After select "CABLE MODE" on microphone, it will display "NO DEVICE CONNECTED" when no radio is connected.

Use the 4m cable to connect the microphone to radio, AT-D578UV displays "ALL DATA CHECKING", the display content of the AT-D578UV radio will be mapped to the Bluetooth microphone.

AT-D578UV radio displays "EXTERNAL CABLE MODE" on the screen, BT01 microphone is able to access the radio menu and do communications now.

Power Off

Press and hold the top [POW] button on microphone to turn off the microphone. AT-D578UV radio will be powered off automatically when BT microphone is off.

Adjust The Volume

In standby state, press the top [POW] button to switch the [CH-]/[CH+] button for volume adjust use.

When screen shows "UpDn Key: Vol Set", press [CH-] to reduce the volume, press [CH+] to increase the volume.

» If the volume is adjusted to the maximum and you still consider it is not loud enough.
» In BT MODE, you can enter into Menu ->Bluetooth->RfBT SPK Gain to adjust the Bluetooth gain level and increase the volume.
» In POWER CABLE MODE, the volume adjustment is realized by the volume switch on AT-D578UV radio.

Set Up VFO Frequency

In Menu->Setting->Radio Set->Key Func, assign a key function to [VFO/ MR].

Press the assigned [VFO/MR] key to switch the radio into VFO frequency mode, and then press the or key to change the frequency.

And it allows input the frequency by keypad on microphone to change the frequency rapidly, for example, input 4,5,0,1,2,5,0,0 or 4,5,0,1,2,5,# to obtain 450.125MHz.

» Normally you shall input 8 digits to change the frequency, in case the end of the frequency is 0, you can press # key to confirm the valid frequency instead of input several 0.

Select a Channel

Press the assigned [VFO/MR] key to switch the radio into channel mode, and then press the top [POW] button to switch the [CH-]/[CH+] button for channel adjust use.

And it allows input the channel number by keypad on microphone to access the channel rapidly, for example, input 0,0,9,9 a total of 4digits will switch to channel 99. In case the input channel number is not in the current zone, the microphone will emit "du" beep and stay at the current channel.

Select a Zone

Press the assigned [VFO/MR] key to switch the radio into channel mode first.

Operation 1: Press the or key to change the zone.
Operation 2: Go to Menu Zone, select a zone from the zone list.
Operation 3: In Menu Setting Radio Set Key Func, assign a key function to [Zone Select]. Press the assigned [Zone Select] key, and input the zone number and confirm.

Make a Call

Press and hold the [PTT] button to start a call at the current channel, the left red indicator lights on and the radio is transmitting. Release the [PTT] button to stop the transmitting.

Receive a Call

When the radio receives a call, the right green indicator lights on and the radio is receiving.

Noise Reduction function

Enable the noise reduction function can reduce background noise and ambient noise effectively, and make calls between users clearer.

Go to Menu Settings Radio Set Voice Func Noise Reduce(RX), set the noise reduce level for receiving use, recommend setting is level 3.

Go to Menu Settings Radio Set Voice Func Noise Reduce(TX), set the noise reduce level for transmit use, recommend setting is level 3.

Menu operation

The menu operation on BT microphone is mapped from AT-D578UV radio, the functions are fully same as AT-D578UV radio. Please refer to AT-D578UV for operation.

Programmed Key

It is possible to set different functions for [P1], [P2], [P3] side keys on microphone.

Method 1: In radio Menu Settings Radio Set Key Func

Method 2: In PC software Public Optional Setting BT Bluetooth handset.

Technical Specifications

Qixiang Electron Science & Technology Co., Ltd.
www.anytone.net

Documents / Resources

References

• Handheld Two Way Radio Manufacturer / Walkie Talkie Supplier | Anytone

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download AnyTone BT01 - Bluetooth Microphone Manual