Related Manuals for PMI PROBASICS ZZZ-PAP AUTO
Summary of Contents for PMI PROBASICS ZZZ-PAP AUTO
- Page 1 Owner’s Manual Model No.: 9S-005720 Item No. 7541 Please read the instruction manual before use...
-
Page 2: Table Of Contents
Contents Important Safeguards ..........1 1. Introduction ............3 2. Product Description ..........5 3. Installation ..............6 4. Operation..............7 5. Adding a humidifier ..........11 6. Using the miniSD Card to Collect Data ......11 7. Cleaning & Maintenance..........11 8. Troubleshooting ............13 9. Technical Specification..........14 10. -
Page 3: Important Safeguards
IMPORTANT SAFEGUARDS SAVE THESE INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE USING WARNING – 1. THIS DEVICE IS NOT INTENDED FOR LIFE SUPPORT. It may stop operating due to power interruption but no hazards to patient. 2. If oxygen is used with the device, the oxygen flow must be turned off when the device is not in use. Explanation of the Warning: When the device is not in operation and the oxygen flow is left on, oxygen delivered into the tubing may accumulate within the device’s enclosure and create a risk of fire. - Page 4 DANGER -To reduce the risk of electrocution: Floor 1. Always unplug this product immediately after using. Marlboro, New Jersey 07746 2. Do not use while bathing. 3. Do not place or store product where it can fall or be pulled into a tub or sink. www.pmiusa.biz xxxxxx-6130 V1.0 4.
-
Page 5: Introduction
1. Introduction This manual should be used for initial set up of the system and saved for reference purpose. General Information Obstructive Sleep Apnea (OSA) is a condition that an intermitted and repetitive obstruction of the upper respiratory tract causes a complete (apnea) or partial (hypopnea) block of breathing airflow during sleep. - Page 6 EMC Warning Statement This equipment has been tested and found to comply with the limits for medical devices to the EN 60601-1-2:2007. These limits are designed to provide reasonable protection against harmful interference in a typical medical installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to other devices in the vicinity.
-
Page 7: Product Description
2. Product Description Components including: (1) Main CPAP device (2) Detachable power cord (3) User manual (4) Flexible air tubing with 1.8 m length (5) Full face or nasal mask and headgear straps (Optional, Always use CE certified and 510(k) cleared mask for CPAP) (6) Carrying bag (optional) (7) miniSD card and USB cable... -
Page 8: Installation
3. Installation 3.1 Unpacking To secure its contents inside, the CPAP device and accessories are bundled in a paper packaged box. Unpack this box by removing the CPAP and its accessory and checking for any damage, which may have occurred during shipping. If there are damages, please contact your dealer immediately. 3.2 Setting Up 1) Connect the power cord to CPAP device and plug into main electrical outlet. -
Page 9: Operation
4. Operation NOTE: Always read the operating instruction before use. Control Panel Description 3. To Re-set the Compliance Meter & Total Meter 1. Press "MENU" to select [TM XXXX.X hr] or [CM XXXX.X hr] menu while in the Button arrangement on control panel and main use of the buttons: standby screen. - Page 10 4.2 Function Description (1) Ramp Time (only CPAP mode) Ramp time function allows the user to fall asleep with a lower, more comfortable pressure and helps them gradually become accustomed to increasing treatment pressure. The second "MENU" [Ramp XX MIN] "MENU"...
- Page 11 "UP" "DOWN" button to set PRODUCT PURSUANT TO THE TERMS CONTAINED HEREIN. PMI SHALL NOT BE LIABLE FOR the current time. ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES WHATSOEVER. (12) Turn off the Device Remove the power cord from the electrical outlet, and disconnect power cord from the power THIS WARRANTY SHALL BE EXTENDED TO COMPLY WITH STATE/PROVINCIAL LAWS AND socket on the back of device.
- Page 12 < 4.0 ~ 20.0 > cmH < 4.0 ~ 19.0 > cmH THIS WARRANTY IS EXTENDED ONLY TO ORIGINAL PURCHASER/USER OF OUR PRODUCTS. PMI WARRANTS ITS PRODUCTS TO THE ORIGINAL PURCHASER TO BE FREE FROM DEFECTS (Total Meter) < xxxx.x > hr IN MATERIAL AND WORKMANSHIP FOR TWO YEARS.
-
Page 13: Adding A Humidifier
Separation distance according to frequency of transmitter m output power NOTE: When the Probasics Zzz-PAP AUTO CPAP device is used with the heated humidifier, of transmitter its power supply is from the power socket outlet of the heated humidifier. Do not... -
Page 14: Troubleshooting
7.2 Tubing and Mask The tubing and mask should be checked and cleaned regularly. Please refer to the cleaning instruction packaged with the accessories. 1. Disconnect the air tubing from the air outlet of the device. 2. Remove the air tubing and headgear straps from the mask. Guidance and Manufacturer’s Declaration- Electromagnetic Immunity: 3. - Page 15 The table below lists troubleshooting solutions for the problems that may happen. If the problem persists, contact your equipment provider. P r o b l e m P o s s i b l e C a u s e s S o l u t i o n s 1.
-
Page 16: Technical Specification
9. Technical Specifications I t e m S p e c i f i c a t i o n s Power Supply Universal power supply, AC100-240V, 50/60 Hz, 0.5-0.3A Pressure Range 4-20 cmH O (adjustable in 0.5 cmH O increments) Initial Pressure 3-19 cmH O (adjustable in 0.5 cmH...
Need help?
Do you have a question about the PROBASICS ZZZ-PAP AUTO and is the answer not in the manual?
Questions and answers