GE HS15-66a-9G-CUL Important Safety Instructions

MODEL NO. HS15-66a-9G-CUL
FOR INDOOR USE ONLY
IMPORTANT SAFETY INSTRUCTIONS
When using electric products, basic precautions should always be followed including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
a)
Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When
b)
products are used in outdoor applications, connect the product to a Ground Fault Circuit Interrupting
(GFCI) outlet. If one is not provided, contact a qualified electrician for proper installation.
This seasonal use product is not intended for permanent installation or use.
c)
Do not mount or place near gas or electric heaters, fireplaces, candles or other similar sources of heat.
d)
e) Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails.
Do not let lamps rest on the supply cord or on any wire.
f)
Unplug the product when leaving the house, when retiring for the night, or if left unattended.
g)
h) This is an electric product-not a toy! To avoid risk of fire, burns, personal injury and electric shock it
should not be played with or placed where small children can reach it.
Do not use this product for other than its intended use.
i)
Do not hang ornaments or other objects from cord, wire, or light string.
j)
k) Do not close doors or windows on the product or extension cords as this may damage the wire insulation.
Do not cover the product with cloth, paper or any material not part of the product when in use.
l)
This product is equipped with push-in type lamps. Do not twist lamps.
m)
n) This product employs overload protection (fuse). A blown fuse indicates an overload or short -circuit
situation. If the fuse blows, unplug the product from the outlet. Also unplug any additional strings or
products that may be attached to the product, Replace the fuse as per the user servicing instructions
(follow product marking for proper fuse rating) and check the product. If the replacement fuse blows, a
short-circuit may be present and the product should be discarded.
Read and follow all instructions that are on the product or provided with the product.
o)
SAVE THESE INSTRUCTIONS
p)
USE AND CARE INSTRUCTIONS
When the product is placed on a live tree, the tree should be well maintained and fresh. Do not place
a)
on live trees in which the needles are brown or break off easily. Keep the tree holder filled with water.
b) If the product is placed on a tree, the tree should be well secured and stable.
Before using or reusing, inspect product carefully. Discard any products that have cut, damaged, or frayed wire
c)
insulation or cords, cracks in the lampholders or enclosures, loose connections, or exposed copper wire.
d) When storing the product, carefully remove the product from wherever it is placed, including tree, branches,
or bushes, to avoid any undue strain or stress on the product conductors, connections, and wires.
When not in use, store neatly in a cool, dry location protected from sunlight.
e)
USER SERVICING INSTRUCTIONS
Replace the fuse.
a) Grasp plug and remove from the receptacle or other
outlet device. Do not unplug by pulling on cord.
b) open fuse cover. Slide open the fuse access cover on top
of attachment plug towards blades.
c) Remove fuse carefully.
d) Risk of fire. Replace fuse only with 3 Amp, 125 Volt fuse (provided with product).
e) Close fuse cover. Slide closed the fuse access cover on top of attachment plug.
f ) Risk of fire. Do not replace attachment plug. Contains a safety device (fuse) that
should not be removed. Discard product if the attachment plug is damaged.
审核:
-SEE OTHER SIDE-
种类明细
Replace the lamp.
1. Grasp plug and remove from the receptacle or
other outlet device. Do not unplug by pulling on cord.
2. Pull lamp and plastic base straight out of lampholder.
3. Replace lamp with only 2.5 Volt, 0.425 Watt,
super bright type lamp (provided with product).
If the new lamp base does not fit in lampholder, follow the steps below step 3.
a) Remove the base of burned out lamp by straightening lamp leads and
gently pull lamp out.
b) Thread leads of new lamp through holes in old base with one lead in each hole.
c) After lamp is fully inserted into base, bend each lead up, like other lamps in the
light set so that the leads will touch the contacts inside the lampholder.
To reduce the risk of overheating replace burned-out lamps promptly. Use 2.5 Volt, 0.425 Watt lamps only.
Connecting Sets End to End
lowest of the indicated maximum wattage on the cord tag near the connected product's receptacle.
If connecting to a lighting string that does not have a Wattage (W) rating {found on the tag
within 6 inches of the plug} calculate the wattage as follows: Multiply the current (___ A)
which is on the flag-type tag by 120.
For Example: Lighting string is rated 120 V, 60 Hz, 0.2 Amps. 0.2 X 120 = 24 Watts
Add the wattage of each light string together for a total of 216 Watts or less. (Do not exceed 216 Watts)
CAUTION:
leaves or branch coverings of metal or materials which look like metal, and b) Do not mount or support
strings in a manner that can cut or damage wire insulation.
For questions and/or assistance, call customer service at 1-877-398-7337
or visit us on the web at www.geholidaylighting.com
©2019 Nicolas Holiday Inc., 9F., No. 37, Guangfu North Rd. Taipei, Taiwan 10560 All rights reserved.
TROUBLESHOOTING
PROBLEM
If the product One or more of the based bulbs may
does not light have loosened from the socket during
transporting. There is a break in the
circuit between the bulb leads and the
socket terminals. Fuse(s) may have
moved.
If a bulb is Bulbs may have hit against each other
broken when transporting
If a bulb burns Incorrect bulb, premature bulb failure or
out voltage is too high
复核:
-CONTINUED FROM OTHER SIDE-
When multiple products are connected together, do not exceed the
To reduce the risk of fire and electric shock: a) Do not install on trees having needles,
POSSIBLE CAUSE
Unplug the set at the outlet. Starting with the
first unlit bulb, gently push (don' t twist) each
bulb base firmly into the socket. If still does
not light, then remove each based bulb to
check for out of place lead wires. Open fuse
door and check fuses.
Mark socket(s) with a piece of tape and
unplug the set before removing the based
bulb from the socket. Replace the broken
bulb. Should another bulb flicker while doing
this that is a faulty bulb. Replace with a new
bulb.
The remaining bulbs should remain lit.
However, it is best to replace burned out
bulbs as soon as you find them.
制表: 康小玲
SH-19 PRINTED IN CHINA
CORRECTIVE ACTION