Summary of Contents for Gallagher MorphoAccess Sigma Lite
- Page 1 MorphoAccess Installation Installation Guide MorphoAccess Installation Guide | Edition 11 | April 2019 Copyright © Gallagher Group Limited Page 1...
- Page 2 Although every commercially reasonable effort has been taken to ensure the quality and accuracy of the information, Gallagher Group makes no representation as to its accuracy or completeness and it should not be relied on as such. To the extent permitted by law, all express or implied, or other representations or warranties in relation to the information are expressly excluded.
-
Page 3: Table Of Contents
Encoding Morpho Cards for Verification ..................53 Performing Overrides on a Morpho Biometric Reader ..............54 Terminals with Biometric Readers ....................56 Troubleshooting ..........................57 MorphoAccess Installation Guide | Edition 11 | April 2019 Copyright © Gallagher Group Limited Page 3... -
Page 4: Introduction
The Biometric Integration feature provides the ability for Morpho biometric readers to be connected to Gallagher Command Centre and configured as hardware items, for the purpose of biometric identification. -
Page 5: Before You Begin
All Morpho resources and documents are compressed into the Morpho Utilities.zip, located at the • root level of the Command Centre installation files, available from the ftp server or on DVD disc on request. MorphoAccess Installation Guide | Edition 11 | April 2019 Copyright © Gallagher Group Limited Page 5... -
Page 6: Installation
The Biometric Dongle Driver must be installed on the Command Centre server and any workstation that will be capturing biometrics. Either of the following dongle drivers work with Gallagher Command Centre: - SafeNet Dongle: USB VERIF (Part No. C864401) or USB IDENT (Part No. C864403/C864405) - Morpho ACS Dongle: V2 USB VERIF (Part No. -
Page 7: Morpho Acs - Verif / Ident Dongle Type
3. Click the Next button. The Destination Folder screen displays. 4. Select your installation directory and click the Next button. The Ready to install screen displays. MorphoAccess Installation Guide | Edition 11 | April 2019 Copyright © Gallagher Group Limited Page 7... -
Page 8: Installing Mso300 And Mso Fvp Drivers
The installation wizard closes and a ‘Restart PC’ pop-up displays. 8. Click the No button. A restart of the PC does not need to be done until after you install the License Manager. MorphoAccess Installation Guide | Edition 11 | April 2019 Copyright © Gallagher Group Limited Page 8... -
Page 9: Installing The License Manager
3. Open the VC12redist_x86 folder and run the executable. Work your way through each screen. 4. Once the Microsoft Redistributables have been installed, restart the computer. MorphoAccess Installation Guide | Edition 11 | April 2019 Copyright © Gallagher Group Limited Page 9... -
Page 10: Installing The Verif Dongle Maci License
4. From the license files provided with the dongle, select the appropriate license file for the dongle plugged into the PC, and click the Open button. The message “License has been correctly set” displays. 5. Click the OK button. MorphoAccess Installation Guide | Edition 11 | April 2019 Copyright © Gallagher Group Limited Page 10... -
Page 11: Installing Morphoaccess Readers
6. Unplug the USB memory stick from the MA Sigma Series reader when the reader restarts. The MA Sigma Series reader should now be ready to be connected to the same network as the Gallagher Command Centre system. MorphoAccess Installation Guide | Edition 11 | April 2019 Copyright ©... -
Page 12: Configuring Ip Address - Sigma Readers Using Ma5G Native Mode
5. Click on Terminal Settings to expand the list below it, and then click Communication. 6. Enter the IP Address, Subnet Mask and Gateway for your reader, and click the Save button. MorphoAccess Installation Guide | Edition 11 | April 2019 Copyright © Gallagher Group Limited Page 12... - Page 13 7. Click Date Time from the Terminal Settings expanded list. 8. Enter the date and time and click the Save button. MorphoAccess Installation Guide | Edition 11 | April 2019 Copyright © Gallagher Group Limited Page 13...
-
Page 14: Supported Morphoaccess Readers
Factory Sigma Readers with Firmware 4.5.1 default to MA5G mode. Sites using Command Centre versions older than vEL7.80 will need to change the Sigma Reader firmware to MA2G4.5.1 (Legacy Mode) firmware. Please contact Gallagher Technical Support for assistance if any issues arise. • 6.2.1 Legacy Morpho Readers... -
Page 15: Sigma Series Morpho Readers
• are added to Command Centre as a Morpho Biometric Reader item. • can have encrypted network communications (for access configuration and ‘biometric templates’). MorphoAccess Installation Guide | Edition 11 | April 2019 Copyright © Gallagher Group Limited Page 15... -
Page 16: Upgrading The Morphoaccess Reader Firmware
6. Double-click the MBTB icon on your desktop. Upgrading the Firmware 1. From the MorphoBioToolbox Connection screen, select the Tools button. 2. Click the Firmware Upgrade tab. MorphoAccess Installation Guide | Edition 11 | April 2019 Copyright © Gallagher Group Limited Page 16... - Page 17 Note: You may get prompted for an interim firmware version if your current version is significantly older than the version you are attempting to upgrade to. MorphoAccess Installation Guide | Edition 11 | April 2019 Copyright © Gallagher Group Limited Page 17...
-
Page 18: Physically Installing Morphoaccess Readers
Power Supply * 12V + (Red) 12V + GND - (Black) GND - * See Power Supply Requirements (on page 20) for further detail. MorphoAccess Installation Guide | Edition 11 | April 2019 Copyright © Gallagher Group Limited Page 18... - Page 19 Power Supply * 12V + (Red) 12V + GND - (Black) GND - * See Power Supply Requirements (on page 20) for further detail. MorphoAccess Installation Guide | Edition 11 | April 2019 Copyright © Gallagher Group Limited Page 19...
-
Page 20: Power Supply Requirements
• 12 VDC supply with a minimum of 2.5 Amp. At 12 VDC (30 watts) IMPORTANT: It is important NOT to connect the MWC Terminal to the Gallagher Controller or URI 12VDC output. The current requirements of the MWC exceeds the 12VDC supply from Gallagher hardware.
Need help?
Do you have a question about the MorphoAccess Sigma Lite and is the answer not in the manual?
Questions and answers