HAMPTON BAY Ceiling Fan Remote Control 99432 Manual

Safety Information

To avoid possible electrical shock, turn the electricity off at the main fuse box before wiring. If you feel you do not have enough electrical wiring experience, contact a licensed electrician.

Incorrect wire connections will damage this receiver.

To reduce the risk of fire or injury, do not use this product in conjunction with any variable (rheostat) wall control.

NOTE: The battery will weaken with age and should be replaced before leaking takes place as this will damage the hand unit. Dispose of the used battery properly, keep the battery out of the reach of children.

1. YOU MUST SET CEILING FAN TO HIGH SPEED AND LIGHT KIT (IF ANY) TO ON POSITION BEFORE OPERATING REMOTE CONTROL.
2. The supply to the remote control receiver should be connected through a mains switch, i.e. existing wall switch.
3. Disconnect from power supply at wall switch before working on remote control receiver or ceiling fan.
4. Install receiver into the ceiling fan canopy of the fan to ensure proper protection.
5. This unit is to be used for the control of ceiling fan and in a AC110/120V 60Hz power supply only.
6. Do not install in damp locations or immerse in water. (For indoor use only.)
7. Do not pull on or cut leads shorter.
8. Do not drop or bump the unit.
9. Do not mix old and new batteries.
10. Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad, ni-mh, etc.) batteries.

Warranty

The supplier warrants the remote control and receiver to be free from defects in workmanship and material present at time of shipment from the factory for a period of one year after the date of purchase by the original purchaser. To obtain warranty service, you must present a copy of the receipt as proof of purchase. All costs of removing and reinstalling the product are your responsibility.
Contact the Customer Service Team at 1-855-HD HAMPTON or visit www.HAMPTONBAY.COM

Pre-Installation

TOOLS REQUIRED

PACKAGE CONTENTS

This product and/or components are governed by one or more of the following U.S. Patents: 5,947,436; 5,988,580; 6,010,110; 6,046,416, 6,210,117 and other patents pending.

Installation

Setting the codes on the remote control and receiver

NOTE: The frequencies on your receiver and hand unit have been preset at the factory. Before installing the receiver, make sure the dip switches on the receiver and hand unit are set to the same frequency. The dip switches on the hand unit are located inside the battery compartment.

NOTE: The battery will weaken with age and should be replaced before leaking takes place as this will damage the hand unit. Dispose of the used battery properly, keep the battery out of the reach of children.

NOTE: It is imperative that the code used for both transmitter and receiver is exactly the same, otherwise remote controller will not work.

Setting the Code on the Remote

• Remove the battery cover on the back of the remote control by pressing firmly on the arrow and sliding the cover off.
• Slide the code switches to your choice of either up or down. The factory setting is up.
• For fans with dimmable bulbs, slide the "Light Function" switch (O/D) to the position marked "D". If you are using non dimmable bulbs slide the "Light Function" switch to the "O" position.
• Install two 1.5V AAA batteries (included).
• Replace the battery cover on the remote control.

Setting the Code on the Receiver

• Slide the code switches on the receiver to the same positions as set on the remote control.

Installing the rubber isolated pads

• Loosen the two screws provided with the outlet box; insert two rubber isolated pads (F) between the mounting bracket and the outlet box; firmly tightened the two screws.
  

Installing the receiver

To reduce the risk of fire or electric shock, remember to disconnect power. The electrical wiring must meet all local and national electrical code requirements. The electrical source and fan must be 110/120 volt, 60Hz. Do not use this product in conjunction with any variable wall control. Incorrect wire connection can damage this receiver.

If fan or house wires are a different color, have this unit installed by a licensed electrician.

Do not install in a damp location or immerse in water (For indoor use only). Do not pull on or cut leads shorter. Do not drop or bump the unit.

NOTE: The ceiling fan must be set at HIGH speed and light kit (if installed) should be set to the ON position.

NOTE: For better performance with the WINK system, the T-Shaped antenna stick should be mounted to the ceiling outside of the fan's ceiling canopy using the pre-mounted doublestick tape and wood screw (included).

• Position the house supply wires (AAA) to one side of the slide-on mounting bracket; position the fan wires (BBB) to the opposite side.
• Insert the narrow end of the receiver (as shown, flat side towards the ceiling) into the slide-on mounting bracket until it rests on top of the ball/downrod assembly. The canopy comes up to cover the receiver and bracket.

Wiring the receiver to the household wiring

To avoid possible electrical shock, turn the electricity off at the main fuse box before wiring. If you feel you do not have enough electrical wiring knowledge or experience, contact a licensed electrician.

Each wire not supplied with this fan is designed to accept up to one 12-gauge house wire and two wires from the fan. If you have larger than 12-gauge house wiring or more than one house wire to connect to the fan wiring, consult an electrician for the proper size wire nuts to use.

Use the wire connecting nuts (AA) supplied with your fan. Secure the connectors with electrical tape and ensure there are no loose strands or connections.

• Spread the wires apart so that the green and white wires are on one side of the outlet box and the black wire is on the other side.
• Connect the green fan wires to the household ground wire (this may be a green or bare wire) using a wire connecting nut (AA).
• Connect the receiver black (or red) wire to the household black (hot) wire using a wire connecting nut (AA).
• Connect the receiver white wire to the household white wire (neutral) wire using a wire connecting nut (AA).
• Secure each wire connecting nut using electrical tape.
  

Wiring the fan to the receiver

Use the wire connecting nuts (AA) supplied with your fan. Secure the connectors with electrical tape and ensure there are no loose strands or connections.

• Connect the fan motor white wire to the receiver white wire using a wire connecting nut (AA).
• Connect the fan motor black wire to the receiver black wire using a wire connecting nut (AA).
• Connect the fan motor blue wire to the receiver blue wire using a wire connecting nut (AA).
• Secure each wire connecting nut using electrical tape.
• Turn the wire connecting nut (AA) upward and push the wiring into the outlet box (MM).
  

Operating Your Remote Control

Operating the remote control

- Press and release the button to turn the fan on or off.
Press and hold the button for 3 seconds to use the "walk away time delay"; this will activate the light for 30 seconds (if you are using dimmable bulbs the light will be activated at 50% brightness.

- Fan Speed - LED's on the fan speed button will illuminate to the corresponding speed.

- Press button once - turns the fan on high speed.
- Press button twice - turns the fan on medium-high speed.
- Press button three times - turns the fan on medium-low speed.
- Press button four times - turns the fan on low speed.
Press button five times - fan will turn off.

- Light ON/OFF
Press and release the button to turn the light on or off.
If you are using dimmable bulbs and you have previously set the dip switch in your remote control to the "D" position, press and hold the button to activate the dimmer function.

- Comfort Breeze - Press and release the button to enable Comfort Breeze TM; this will change your fan speed randomly, simulating a relaxing breeze. To cancel this feature press or .

- Timer
- While the fan is on press button once - turns on a 2 hour run timer.
- While the fan is on press button twice - turns on a 4 hour run timer.
- While the fan is on press button three times - turns on a 8 hour run timer.

Operating Fan with the WINK App

Downloading the WINK Application

• Using your smart device, navigate to the application store (Apple App Store or Google Play). Download the free WINK app and create an account.
  

Connecting to the WINK Hub

• Ensure your WINK Hub is connected to WiFi by confirming the indicator light is a solid blue color.
• With the app open, select "add a product."
• Choose the WINK Hub and follow the instructions on the app to add your fan.

NOTE: Be sure your WINK Hub is plugged in and within range of your fan. Refer to Wink HUB user manual for the range.

Pairing the Fan to the WINK Hub

• When instructed, turn on your fan. Once pairing is successful, the fan will turn on at low speed and the light will blink 5 times.
  

NOTE: If using a dimmer with these lights, set dimmer at highest setting for best results.

NOTE: Reset your fan if the pairing is taking longer than expected. Turn off your fan for 3 seconds, then turn it back on for 3 seconds. Repeat these steps 5 times. The light will blink 3 times when factory reset is successful. If the pairing failed, please reset the device to original setting and re-start the pairing.

Fan Light Settings

• During set up, the customer is asked if the fan has a light kit.
• If your fan has a light, select "Fan Light On."
• If your fan does not have a light, select "Fan Light Off."
• Press SAVE to confirm.

Operating Your Remote Control

Fan Speed

• OFF - Turns fan off
• 1- Turns the fan to Low speed.
• 2- Turns the fan to Medium speed.
• 3- Turns the fan to Medium 2 speed.
• 4- Turns the fan to High speed.
• BREEZE- Randomly alternates fan speeds to create an organic breeze effect.

Fan Light

• OFF/ON - Turns fan light off or on. Select and slide to dim or brighten light.

Timer

When on "fan control screen," press settings button in upper right corner to display the settings panel.

• Select fan to display control panel.
• Scroll down the control panel and select "Set Timer."
  
• Scroll through the hours and minute columns to select the duration of the timer.
  
• Press OK to start the timer.
  

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment.
FCC ID: KUJCE10406, KUJCE10407
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Documents / Resources

References

• The Home Depot Logo
• App Store - Apple
• Google Play

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download HAMPTON BAY Ceiling Fan Remote Control 99432 Manual