Related Manuals for Thundercomm TurboX C4290
Summary of Contents for Thundercomm TurboX C4290
- Page 1 EmpoweringEveryIoTDevicewithOurTechnology Thundercomm TurboX C4290/CM4290 Development Kit Hardware User Manual Rev. V1.0 JUN 7, 2022 DN: tc‐j‐22110...
- Page 2 Thundercomm TurboX C4290 CM4290 Development Kit Hardware User Manual Revision History Revision Date Description 1.0 JUN 7, 2022 Initial release. Copyright© 2022 Thundercomm Technology Co., Ltd. All rights reserved.
- Page 3 Thundercomm TurboX C4290 CM4290 Development Kit Hardware User Manual Table List Table 2‐1. Board layout description Table 2‐2. Feature description Table 3‐1. Status and function description of dip switch Table 3‐2. TurboX C4290/CM4290 configuration Table 3‐3. Boot config switch parameters Table 3‐4. Function description of LED indicators Copyright© 2022 Thundercomm Technology Co., Ltd. All rights reserved.
- Page 4 About This Document Illustrations in this documentation might look different from your product. Depending on the model, some optional accessories, features, and software programs might not be available on your device. Depending on the version of operating systems and programs, some user interface instructions might not be applicable to your device. Documentation content is subject to change without notice. Thundercomm makes constant improvements on the documentation of your computer, including this guidebook. Button, tool, and key names appear in bold font, for example, click Save or press Enter. Folders and files are formatted in italic, for example, turbox_flash_flat.sh. Copyright© 2022 Thundercomm Technology Co., Ltd. All rights reserved.
-
Page 5: Table Of Contents
Table of Contents Chapter 1. Introduction ...................... 5 Chapter 2. Product Overview ..................... 6 2.1. Board introduction ..........................6 2.2. Overview ...............................7 2.3. Features ..............................8 2.4. Block diagram ............................9 2.5. Components ............................9 Chapter 3. Specifications for Common DK Board .............. 10 3.1. Switches ... -
Page 6: Introduction
Chapter 1. Introduction This document introduces the features of TurboX C4290/CM4290 DK (Development Kit), aiming to guide the developer on product design and verification based on Thundercomm TurboX C4290/CM4290 SOM (System‐on‐module). “TurboX” referred to herein is the English text of our registered trademark: . Version identification: You can find the following information on your DK, for example: CM4290 INTERPOSER BOARD Ver.03, which means the hardware version number of your board is 03. Safety precautions: Required output of the power adaptor is 12V, with the current greater than or equal to 2A. It is ... -
Page 7: Product Overview
Chapter 2. Product Overview TurboX C4290/CM4290 DK (Development Kit) is one of the most powerful boards with high‐performance Thundercomm C4290/CM4290 SOM, rich peripherals and flexible interfaces. With integrated Android OS (Operating System), it is designed for evaluating, optimizing, testing, and releasing intelligent hardware products for developers, OEMs (Original Equipment Manufacturers), ... -
Page 8: Overview
2.2. Overview Figure 2‐2. Board Layout Table 2‐1. Board layout description UART debug connector 11. PCIE connector * 21. SIM card slot 1 ** 31. Volume up button USB 3.1 Type‐A connector 12. SW 1300 22. SOM plate 32. Volume down button Micro USB connector 13. FM antenna connector 23. Camera connector 2 33. Power on button USB 3.1 Type‐C connector 14. Camera connector 5 * 24. Camera connector 3 * 34. Battery connector SW 2100 15. GPS antenna connector 25. SW 1102 35. -
Page 9: Features
2.3. Features Table 2‐2. Feature description Item Specification CPU: A customized 64‑bit Arm v‐8.0 compliant applications processor (Qualcomm® Kryo™ 260 CPU) Kryo Gold: quad high‐performance cores 2.0 GHz Processor Kryo Silver: quad low‐power cores 1.8 GHz DSP: Qualcomm® Hexagon™ Vector eXtensions (dual HVX at 1.0 GHz) LPDDR4x 4GB + eMMC 64GB Memory 1 x MIPI DSI: support one 4‐lane MIPI DSI D‐PHY port Display HDMI out: Support 1080P 1 x USB Type‐C host or 1 x micro USB USB 1 x Micro USB 2.0 connector (for UART debug) 1 x TF card SDIO 2 x UIM（Only for CM4290） UIM 3 x MIPI CSI: support 4‐lane MIPI CSI D‐PHY port Camera ... -
Page 10: Block Diagram
2.4. Block diagram Figure 2‐3. Block Diagram 2.5. Components The Thundercomm TurboX C4290/CM4290DK includes the following hardware components: 1 x Common DK board 1 x C4290/CM4290 interposer board 1 x 12V/2A power supply (with a 5.5mm x 2.5mm connector) 1 x Wi‐Fi antenna 1 x GPS antenna 2 x LTE antennas 1 x audio board 1 x sensor board 1 x camera module 1 x FPCA 2 x speakers ... -
Page 11: Specifications For Common Dk Board
Chapter 3. Specifications for Common DK Board 3.1. Switches 3.2.1. Dip switch Refer to Figure 3‐1 and Table 3‐1 for the details of the dip switch (No. 23 in Figure 2‐2). Figure 3‐1. Locate Dip Switch Table 3‐1. Status and function description of dip switch A No. Status Function Recommendation Comment ON: PM_GPIO_08_BL_PWM_OUT OUTPUT TO LS Board 1 ON/OFF OFF ‐ OFF: No use ON: PM_GPIO_08_BL_PWM_OUT OUTPUT TO LCD0; display‐functi 2 ON/OFF ON OFF: No use 1‐12/2‐11, only one for use. on ON: SM_GPIO_81 OUTPUT TO LS Board 3 ON/OFF OFF ‐ OFF: No use ON: SM_GPIO_81 OUTPUT TO LCD0 TE; 4 ON/OFF OFF ... - Page 12 No. Status Function Recommendation Comment 1 ON/OFF No use ‐ ‐ 2 ON/OFF No use ‐ ‐ ON: SM_GPIO_46 OUTPUT TO LS Board, 3 ON/OFF Cam0_dovdd_1V8_EN OFF ‐ OFF: No use ON: SM_GPIO_46 OUTPUT TO Cam0, csi0 power Cam0_dovdd_1V8_EN; 4 ON/OFF ON on OFF: No use3‐10/4‐9, only one for use. 5 ON/OFF No use ‐ ‐ 6 ON/OFF No use ‐ ‐ C ...
- Page 13 ON: NFC control signal disable; 4 ON/OFF OFF ‐ OFF: NFC control signal enable 5 ON/OFF No use ‐ ‐ ON: USB2.0 disable; 6 ON/OFF OFF ‐ OFF: USB2.0 enable Table 3‐2. TurboX C4290/CM4290 configuration SOC SKUx Thundercomm Product No. (TPN) Model SKU4 4+64GB TurboX C4290 C4290-E46-ACXPWXX SKU3 3+32GB TurboX C4290 C4290-E33-ACXPWXX QCM4290 SKU6 3+32GB TurboX CM4290 CM4290-EA-E33-ACXPWXX SKU7 4+64GB TurboX CM4290 CM4290-EA-E46-ACXPWXX...
- Page 14 3.2.2. Boot config switch Refer to Figure 3‐2 to locate the boot config switch (No. 15 in Figure 2‐2). Figure 3‐2. Locate Boot Config Switch Table 3‐3. Boot config switch parameters Pin# Signal Description On Off 1 BOOT_CFG0 WDOG High Low 2 BOOT_CFG1 Fast_BOOT bit 0 1 0 3 BOOT_CFG2 Fast_BOOT bit 1 1 0 4 BOOT_CFG3 Fast_BOOT bit 2 1 0 5 BOOT_CFG4 Fast_BOOT bit 3 1 0 6 CBL_PWR_N ...
-
Page 15: Connectors
3.2. Connectors 3.2.1. Micro USB connector C/CM4290 not support Micro USB connector 3.2.2. Type‐C USB connector Figure 3‐3. Locate Type‐C USB Connector ... - Page 16 Major functions: Compatible with both USB 3.0 connector and USB 2.0 connector. 3.2.3. Micro USB connector (for UART debug) The DK board is connected to PC with a USB cable via the micro USB connector (for UART debug) (No. 28 in Figure 2‐2). This connector is a log USB port for SOM. On the SOM side, SOM prints log message on the DK board via this connector. The UART signal is converted to USB signal by specific circuit. Figure 3‐4. Locate Micro USB Connector (for UART Debug) ...
- Page 17 3.2.4. 12V DC in jack This connector plugs into a 12V power supply of no less than 2A. The physical size of the connector is 5.5mm‐2.5mm. Figure 3‐5. Locate 12V DC in Jack 3.2.5. HDMI out connector C4290/CM4290 complies with D‐PHY1.1 and DSI 1.02, and supports HDMI 1.4 standard. HDMI Type‐A connector supports up to 1080P@30FPS output. Figure 3‐6. Locate HDMI Out Connector ...
- Page 18 3.2.6. Speaker connectors Figure 3‐7. Locate Speaker Connectors Speaker power: 2W Speaker resistance: 8Ω Connector parameter: 2.00mm pitch/2 pins ...
- Page 19 3.2.7. Antenna connectors Figure 3‐8. Locate Antenna Connectors Wi‐Fi/BT antenna connector is used for connecting antenna for 2.4G/5G Wi‐Fi network. The 1x1 (WCN3988) MIMO (Multiple Input Multiple Output) with two spatial streams IEEE802.11 a/b/g/n/ac WLAN standards are supported. Primary antenna connector is used to connect the primary antenna. 3.2.8. SD card slot Figure 3‐9. Locate SD Card Slot Maximum storage capacity: 128GB Power supply voltage: 1.8V/2.95V 3.2.9. Camera module connectors ...
- Page 20 3.2.10. C/CM4290 only support for Camera0/1/2 Figure 3‐10. Locate Camera Module Connectors 3.2.11. Display panel connector Refer to Figure 3‐12 to connect the display panel to the board. Figure 3‐11. Locate Display Panel Connector ...
- Page 21 3.2.12. Headset connector Refer to Figure 3‐13 to locate the headset connector (No. 31 in Figure 2‐2). Figure 3‐12. Locate Headset Connector 3.2.13. Main battery Refer to Figure 3‐14 to connect main battery to the DK. Figure 3‐13. Locate Battery Connector ...
-
Page 22: Buttons
3.3. Buttons Figure 3‐14. Locate Buttons Power on button: Used to boot up the device, when the board is running, pressing this button will set the device into sleep mode. Volume down button: Used to turn down the volume. Volume up button: Used to turn up the volume. Force USB button: When this button is pressed, the board will be forced to enter the download mode and boot from the USB_HS port during development or factory production. ... -
Page 23: Led Indicators
3.4. LED indicators Refer to Figure 3‐16 and Table 3‐4 for the LED indicators on the board. Figure 3‐15. Locate LEDs Table 3‐4. Function description of LED indicators LED indicator Function ① DC power indicator Indicates the DK power status ② SOM power indicator Indicates the SOM power status ③ Green LED Green LED controlled by the user ④ Red LED Red LED controlled by the user ⑤ Charging indicator Indicates the board charging status ⑥ USB indicator Indicates USB device connection status ... -
Page 24: Sensors
3.5. Sensors Figure 3‐16. Locate Sensors Pressure sensor, using a BMP280, delivers high performance with an IIC interface in all applications that require precise pressure measurement. Its accuracy is ±0.12 hPa, equivalent to ±1 m difference in altitude. Accelerometer + gyrometer sensor, using a LSM6DS3TR‐C , has a full‐scale acceleration range of ±2/±4/±8/±16 g and an angular rate range of ±125/±250/±500/±1000/±2000 dps. Magnetic sensor, using a AK09915, is a 3‐axis magnetometer device suitable for compass application. ALS/proximity sensor, using a TMD2755, features proximity detection and digital ambient light sensing (ALS). ... -
Page 25: Notices
To provide better service, Thundercomm reserves the right to improve and/or modify the products and software programs described in the manuals, and the content of the manual, at any time without additional notice. The software interface and function and hardware configuration described in the manuals included with your development board or system on module might not match exactly the actual configuration of that you have purchased. For the configuration of the product, refer to the related contract (if any) or product packing list, or consult the distributor for the product sales. Thundercomm may use or distribute any of the information you supply in any way it believes appropriate without incurring any obligation to you. The products described in this document are not intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. The information contained in this document does not affect or change Thundercomm product specifications or warranties. Nothing ... - Page 26 E‐mail messages sent to Thundercomm via the Internet are not guaranteed to be completely secure. Thundercomm shall not be liable for any loss incurred by the surfer when transmitting any information over the Internet or for any loss incurred by Thundercomm when sending any information over the Internet at your request. Thundercomm has all rights under other relevant exemptions provided by laws and regulations, and Thundercomm's failure to claim or delay in claiming such rights shall not be deemed to be a waiver of such rights by Thundercomm. Thundercomm reserves the right of final interpretation of this document. ...
-
Page 27: Trademarks
Appendix 2. Trademarks Thundercomm, Thundercomm TurboX, TURBOX, Thundersoft turbox are trademarks of Thundercomm Corporation or its associate companies in China and/or other countries. Intel, Intel SpeedStep, Optane, and Thunderbolt are trademarks of Intel Corporation or its subsidiaries in the U.S. and/or other countries. Microsoft, Windows, Direct3D, BitLocker, and Cortana are trademarks of the Microsoft group of companies. Mini DisplayPort (mDP), DisplayPort, and VESA are trademarks of the Video ... - Page 28 FCC Declaration of Conformity We Thundercomm Technology Co., Ltd declare under our sole responsibility that TurboX C4290 SOM/ TurboX C4290 comply with Part 15 of FCC Rules. FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
- Page 29 transmitter. This device is intended only for OEM integrators under the following conditions: (1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and (2) The transmitter module may not be co-located with any other transmitter or antenna, IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid...
- Page 30 Industry Canada Statement This device complies with license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS standard(s). Operation is subject to the following two conditions: this device may not cause harmful interference, and this device must accept any interference received, including interference that may cause undesired operation.
- Page 31 Antenna Information Model Type Connector Peak gain ( dBi ) 1461531100 FPC N/A 3 1461531100 N/A 4 Radiation Exposure Statement This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator &...
- Page 32 Note Importante: Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines configurations d'ordinateur portable ou de certaines co‐localisation avec un autre émetteur), l'autorisation du Canada n'est plus considéré comme valide et l'ID ISED ne peut pas être utilisé sur le produit final. Dans ces circonstances, l'intégrateur OEM sera chargé...
Need help?
Do you have a question about the TurboX C4290 and is the answer not in the manual?
Questions and answers