Table of Contents
Advertisement
Quick Links
Congratulations on your purchase of the
MODEL 370 SS
®
unit. This instruction/parts manual is a
guide for operating and servicing your
SAPPHIRE SCIENTIFIC Truckmount
unit.
Proper operation and service are necessary to
ensure the outstanding performance of this unit.
When properly maintained, your Truckmount will
have a long and trouble-free life.
The following service methods outlined in this
manual are detailed in a manner that operation and
servicing may be performed properly and safely.
Because service levels vary due to the skill of the
mechanic, tools and parts availability, ensure that
prior to attempting any repair, you are familiar
with this equipment and have the proper tools.
Any questions regarding the operation, service, or
repair of this unit should be directed to your
nearest SAPPHIRE SCIENTIFIC dealer.
The headings WARNING and CAUTION are
utilized to warn you that steps must be taken to
prevent personal injury or damage to the
equipment. Please make sure that you have read
and understand these instructions entirely before
proceeding with the operation of this unit.
THIS UNIT MUST BE INSTALLED BY THE
DEALER THAT YOU PURCHASED IT
FROM IN ACCORDANCE WITH THE
SAPPHIRE SCIENTIFIC INSTALLATION
PROCEDURES.
BE SURE TO FILL OUT THE WARRANTY
CARD ONLINE AT WWW.SAPPHIRE
SCIENTIFIC.COM
SAPPHIRE SCIENTIFIC
Truckmount cleaning
MODEL 370 SS
Record your units serial number here for future
reference or if you should need to contact the
factory in the future for any reason.
S/N:
This service and operations manual is written
specifically for SAPPHIRE SCIENTIFIC
MODEL 370 SS
Truckmount Cleaning units
®
manufactured by:
SAPPHIRE SCIENTIFIC
2604 Liberator
Prescott, AZ 86301
USA
The information contained in this document is
subject to change without notice and does not
represent a commitment on the part of
SAPPHIRE SCIENTIFIC.
All rights reserved. Copyright 2009 by
SAPPHIRE SCIENTIFIC. No part of this work
may be used or reproduced in any form or means
without the express written consent and permission
of SAPPHIRE SCIENTIFIC.
Published by SAPPHIRE SCIENTIFIC.
First printing: May 2009
Printed in USA
MODEL 370 SS® MANUAL
PART# 49-038
October, 2009
I
Advertisement
Chapters
Table of Contents
Related Manuals for Sapphire Audio 370 SS
Summary of Contents for Sapphire Audio 370 SS
- Page 1 First printing: May 2009 proceeding with the operation of this unit. Printed in USA THIS UNIT MUST BE INSTALLED BY THE DEALER THAT YOU PURCHASED IT MODEL 370 SS® MANUAL FROM IN ACCORDANCE WITH THE SAPPHIRE SCIENTIFIC INSTALLATION PART# 49-038 PROCEDURES.
- Page 2 SAPPHIRE SCIENTIFIC LIMITED WARRANTY Sapphire Scientific Model 270 SS / MODEL 370 SS What Does This Warranty Cover? This warranty covers the Sapphire Scientific Models 270 SS & 370SS and is provided to the original purchaser only. How Long Does This Warranty Last? This warranty runs for: •...
- Page 3 Table of Contents MODEL 370 SS SAPPHIRE SCIENTIFIC...
-
Page 4: Table Of Contents
Operation, Cleaning, Upholstery Cleaning, Stair Tool Cleaning, Flood Restoration, Shut Down and Daily Maintenance, Freeze Protection. SECTION FOUR: MAINTENANCE and SERVICE MAINTENANCE CHART 6. MAINTENANCE 7. GENERAL SERVICE ADJUSTMENTS 8. TROUBLESHOOTING SECTION FIVE: PARTS and ACCESSORIES 9. ILLUSTRATED PARTS LISTINGS 10. ACCESSORIES MODEL 370 SS SAPPHIRE SCIENTIFIC... -
Page 5: Section One: General Information
SECTION 1: GENERAL INFORMATION 1. SAFETY Safety Specifications Installation requirements Fuel requirements Engine oil requirements Chemical requirements Water requirements 2. RECEIVING YOUR TRUCKMOUNT UNIT Dealer responsibility Acceptance of shipment Equipment listing Optional equipment MODEL 370 SS SAPPHIRE SCIENTIFIC... -
Page 6: Safety
SECTION 1 1. SAFETY For Your Safety! The following WARNING labels are on result in personal injury or fatality to your MODEL 370 SS console. These yourself and/or others or property damage. ® labels point out important Warnings and Please follow these instructions carefully! Cautions, which must be followed at all DO NOT remove these decals. - Page 7 (−) terminal first. as belts and pulleys, should be avoided while the unit is running. Severe injury, fatality or 14. DO NOT smoke around the machine. Gas damage may result. fumes could accumulate and ignite. Battery MODEL 370 SS SAPPHIRE SCIENTIFIC...
- Page 8 This unit is equipped with a low pressure shut down switch, which should NOT be bypassed. 20. Always keep your vehicle clean and orderly. Wands, tools and accessories must be securely stowed while driving the vehicle. MODEL 370 SS SAPPHIRE SCIENTIFIC...
- Page 9 Vacuum Pump Hub 180 inch/lbs. 15 ft/lbs. JET SIZING SAPPHIRE SCIENTIFIC recommends that the total floor tool tip size does not exceed #4. Using larger jet sizes on your MODEL 370 SS unit may reduce cleaning ® temperatures. Sapphire Scientific using the Stryker Cleaning...
- Page 10 Prior to beginning the installation, read the unleaded gasoline intended for normal ENTIRE “Installation” section of this manual. automotive use. DO NOT use high-octane Since the MODEL 370 SS Truckmount unt ® gasoline with this unit. weighs (with waste tank and accessories) 1000 lbs., please adhere to the following...
-
Page 11: Receiving Your Truckmount Unit
Part # 18-000 (With shutoff valve Part # 18-001) ACCEPTANCE OF SHIPMENT D. Automatic waste pump kit Part # 68-003 Your MODEL 370 SS Truckmount cleaning ® E. Demand pump system unit was thoroughly tested, checked and Part # 68-002 inspected in its entirety prior to leaving our F. - Page 12 J. KIT, 2004 TF ADAPTER CHEVY Part # 69-032 K. KIT, 2004 TF FUEL INJ. CHEVY Part # 69-033 L. ADAPTOR, 2004 FORD FUEL Part # 69-041 M. ADAPTOR, 2004 FUEL INJ. FORD Part #69-041FI MODEL 370 SS SAPPHIRE SCIENTIFIC...
-
Page 13: Section Two: Installation
Positioning the unit into the vehicle Fastening down the unit and waste tank Dimensional diagrams Installation of fuel lines Trailer fuel tank and fuel line installation Battery Connection Fire extinguisher Console to waste tank connection MODEL 370 SS SAPPHIRE SCIENTIFIC... -
Page 14: Installation
SAPPHIRE screws with flat washers through the waste SCIENTIFIC strongly recommends a side door tank mounting holes. installation for the MODEL 370 SS . We DO ® NOT recommend a rear door installation. 2. Install the provided mounting plates underneath the vehicle floor. -
Page 15: Dimensional Diagrams
SECTION 2 DIMENSIONAL DIAGRAM REAR MOUNT TANK MODEL 370 SS SAPPHIRE SCIENTIFIC... -
Page 16: Installation Of Fuel Lines
A, B, and C type fires be installed into any NEVER store any type of flammable material in commercial vehicle. an enclosed trailer or vehicle. MODEL 370 SS SAPPHIRE SCIENTIFIC... -
Page 17: Console To Waste Tank Connection
SECTION 2 CONSOLE TO WASTE TANK CONNECTION MODEL 370 SS SAPPHIRE SCIENTIFIC... -
Page 18: Section Three: Operation
Water/Heating system Vacuum system Chemical pumping system 5. OPERATION Preparation Starting the unit Priming the chemical pump Automatic waste pump Operation Cleaning Upholstery cleaning Stair tool cleaning Flood restoration/extraction Shut down and daily maintenance Freeze protection MODEL 370 SS SAPPHIRE SCIENTIFIC... -
Page 19: Systems
The water then flows to the the cleaning tool. water box through a float valve, which shuts off the water when the water box is full. MODEL 370 SS SAPPHIRE SCIENTIFIC... -
Page 20: Vacuum System
The use of a quality defoamer The vacuum pump also heats incoming air as it is is recommended. compressed. The hot discharged air is forced down MODEL 370 SS SAPPHIRE SCIENTIFIC... -
Page 21: Chemical Pumping System
This valve may be used to turn the chemical flow ON, OFF, or to PRIME the chemical pump. MODEL 370 SS SAPPHIRE SCIENTIFIC... -
Page 22: Operation
SAPPHIRE SCIENTIFIC DO NOT run this unit in an enclosed area. MODEL 370 SS mobile cleaning unit. The ® DO NOT operate this unit where the exhaust... - Page 23 Also, flush out any debris from your water inlet hose. 1. Connect the water supply hose to the water inlet quick connector on the front of the unit. Connect the hose to the faucet. MODEL 370 SS SAPPHIRE SCIENTIFIC...
-
Page 24: Starting The Unit
If the pump does not prime, then: Place the chemical prime tube into the vacuum hose and seal off the vacuum hose. The vacuum will quickly draw chemical MODEL 370 SS SAPPHIRE SCIENTIFIC... -
Page 25: Automatic Waste Pump
1. Upholstery tools have a lower flow rate and smaller orifices. Adjust the thermostatic After you have completed the previous steps, temperature control to the desired proceed with the cleaning or restoration temperature. To maintain proper cleaning MODEL 370 SS SAPPHIRE SCIENTIFIC... -
Page 26: Stair Tool Cleaning
Microban QGC cleaner is the best product for 4. Adjust the throttle cable to the idle position. cleaning and sanitizing the waste tanks as well as other parts of the system 5. Adjust the thermostatic temperature control to the lowest setting. MODEL 370 SS SAPPHIRE SCIENTIFIC... -
Page 27: Freeze Protection
The following is recommended to Recover all anti-freeze that comes out of the prevent this from occurring during the cold tools and hoses and store in an approved weather season: container. ALWAYS re-use or re-cycle anti-freeze. MODEL 370 SS SAPPHIRE SCIENTIFIC... - Page 28 4. Insert the chemical prime hose into the approved container. Submerge the chemical hose into fresh water. Turn the chemical valve to the PRIME position until the water runs MODEL 370 SS SAPPHIRE SCIENTIFIC...
-
Page 29: Section Four: Maintenance And Service
Vacuum Hoses Battery High Pressure Solution Hoses 7. GENERAL SERVICE ADJUSTMENTS Engine Vacuum Relief Valve Water Pump Drive Belt Solution Outlet Check Valve Chemical Pump Packing Nut Adjustment, Chemical Metering and Selector Valves 33 Pressure Regulator MODEL 370 SS SAPPHIRE SCIENTIFIC... - Page 30 8. TROUBLESHOOTING Water Pump Blower / Vacuum Pump Chemical System Engine MODEL 370 SS SAPPHIRE SCIENTIFIC...
-
Page 31: Maintenance Chart
*****Check pulley and hub set screws after first 50 hours of operation, and again at 100 hours of operation. ******Or every 6 Months. Whichever comes first. *******Or Yearly. Whichever comes first. ********Retention all belts after first 25 hours then at every 100 hours of operation. MODEL 370 SS SAPPHIRE SCIENTIFIC... -
Page 32: Maintenance
A planned preventative ® proper oil level is maintained. NEVER overfill. maintenance program will ensure that your SAPPHIRE SCIENTIFIC MODEL 370 SS ® 2. Change the oil after the first 5 to 8 hours of optimum performance, long operating life, and a operation. -
Page 33: Vacuum Pump
1. Check the oil level weekly on both sides to check for the source of leakage and repair. ensure they are at the proper level. Too little oil will damage and ruin the bearings and gears. Too much oil will result in overheating. MODEL 370 SS SAPPHIRE SCIENTIFIC... -
Page 34: Vacuum Inlet Filter
9) Lower front 2 nuts located under the front the torque values. of blower mounting plate approximately ½” 10) Tip the back of blower up 11) Remove all belts. Install new belts 12) Reverse procedures to install new belts MODEL 370 SS SAPPHIRE SCIENTIFIC... -
Page 35: Water Box
If ON, a spark could occur at the check valves, and inspecting the disk. ground connection terminal, which could cause an explosion if hydrogen gas or gasoline vapors are present. ALWAYS disconnect the negative (−) terminal first. MODEL 370 SS SAPPHIRE SCIENTIFIC... -
Page 36: General Service Adjustments
2. Adjust the position of the belt tensioning adjusting bolt until the proper belt tension is achieved. (3/4” deflection in the center of the belts, half way between the pulleys). MODEL 370 SS SAPPHIRE SCIENTIFIC... -
Page 37: Solution Outlet Check Valve
CHEMICAL PUMP 1. Remove the check valve, ensuring that the small o-ring on the seat comes out with it The MODEL 370 SS unit features a stainless ® 2. Next, remove the seat using a 5/16 in. Allen steel chemical pump and metering system. -
Page 38: Pressure Regulator
100 PSI, it may be necessary to lubricate the pressure regulator o-rings. 2. To adjust the pressure regulator, turn the adjusting knob (while observing the pressure gauge on the control panel) until you reach the desired pressure. MODEL 370 SS SAPPHIRE SCIENTIFIC... -
Page 39: Troubleshooting
CHEMICAL, VACCUM, HEAT TRANSFER, SAFETY and WIRING systems featured in this unit. If there are malfunctions occurring on this unit which you do not understand, refer back to the OPERATION section of this manual and review SYSTEM MODEL 370 SS SAPPHIRE SCIENTIFIC... - Page 40 SECTION 4 MODEL 370 SS SAPPHIRE SCIENTIFIC...
- Page 41 Cleaning tool valve is malfunctioning. Repair or replace valve. Hose inner lining is constricted. Remove restriction or replace hose. Air leak in chemical supply line, priming Check for air leaks. Replace faulty parts. valve or metering valve. MODEL 370 SS SAPPHIRE SCIENTIFIC...
- Page 42 Disassemble the chemical pump and replace the damaged diaphragm. Measure the pump volume. If the pump volume is less than normal, refer to “Loss of Pump Defective cylinder in the water pump. Volume” in the Troubleshooting section in this manual. MODEL 370 SS SAPPHIRE SCIENTIFIC...
- Page 43 Check switch for proper operation, replace as not start tank. necessary. Oil pressure switch (located on Test these components. If any are defective, engine), fuel shut-off solenoid (located replace. Consult the Kohler Engine Operation on engine). and Maintenance Manual. MODEL 370 SS SAPPHIRE SCIENTIFIC...
-
Page 44: Section Five: Parts And Accessories
Inspect check valve for debris or Clean or replace if necessary. damage. SECTION 5: PARTS and ACCESSORIES 9. ILLUSTRATED PARTS LISTINGS MODEL 370 SS SAPPHIRE SCIENTIFIC... -
Page 45: Illustrated Parts Listings
Sheet Metal Engine Water Transfer System Vacuum-Exhaust System Chemical Pumping System Decals Electrical Diagram Waste Tank 10. ACCESSORIES Accessories MODEL 370 SS SAPPHIRE SCIENTIFIC... - Page 46 69-186, ASSY, FRAME, CONTROL PANEL & HOODS, 370 SS Item No. Part Number Description 61-440 ASSEMBLY, FRAME, MODEL 270 & 370 SS 61-447 WELDMENT, CONTROL PANEL 60-389 PANEL, REAR TOP BRACE 58-359 PANEL, TOP, 370 SS 60-336 Model 370 KOHLER Left Side Panel...
- Page 47 ASSY, CONTROL PANEL 11-002 NUT, WELL G 10-32 .375 10-016 SCREW, MACHINE 10-32 X 1 SOCHD SS 58-362 PANEL, LOWER FRONT, MODEL 270 & 370 SS 69-192 ASSY, MANIFOLD BLOCK 69-188 ASSEMBLY, BRACKET, MOUNTING, LOWER LEFT 69-187 ASSEMBLY, BRACKET, MOUNTING, LOWER RIGHT...
- Page 48 69-181 MODEL 370 SS CONTROL PANEL ASSEMBLY Item No. Part Number Description 58-361 Instrument Panel 23-066 MACVALVE, 45A-AA1-DDBJ-4KA 26-004 GUAGE, VAC 30in.HG DUALSCALE 26-010 HOURMETER, HOBBS 26-007 GAUGE,WTR. TEMP 320 DEG 26-005 GAUGE, WTR. PRESS1500PSIDUAL 40-001 CABLE, CHOKE 40-000 CABLE, THROTTLE...
- Page 49 69-181 MODEL 370 SS CONTROL PANEL ASSEMBLY Item No. Part Number Description 58-364 BRACKET, DIVERTER LOCKOUT VALVE 21-007 FTTG,BRB 1/8 PX 5/16 H BR 21-037 ELL, 1/4 IN. BRASS 21-076 BUSHING, 1/4 M X 1/8 F BRASS 21-028 CONN, 1/8 P X 1/4 POLY...
- Page 50 69-190 ASSEMBLY, ENGINE, 370 SS Item No. Part Number Description 45-009 370-SS ENGINE, KOHLER 20HP CHAMP 61-468 ASSEMBLY, EXHAUST TUBE LS, 370 SS 61-469 ASSY, EXHAUST TUBE RS, 370 SS 36-024 GASKET, EXHT KOHLER#2404102-S 36-349 GASKET, EXHAUST B & S #809872 21-329 NIPPLE, 3/8 NPT X 6"...
- Page 51 HOSE, FUEL 1/4" 30R7 21-006 FTTG, BRB 1/4PX5/16H BR 14-011 CLAMP, HOSE FUEL #6 16-034 HOSE, FUEL 1/4" 30R7 36-097 FILTER, FUEL KUBOTA (OEM) 21-166 FTTG, 1/4 MP X 1/4 H BARB 14-022 CLAMP VINYL COVERED COV21092Z1 MODEL 370 SS SAPPHIRE SCIENTIFIC...
- Page 52 Set Screw 60-398 PLATE, BLOWER HOUSING FRONT RING 39-008 ASSY, BEARING & SHAFT 15-027 SNAP RING, 1.187 INTERNAL 66-215 PULLEY, 3L BELT X 2.340 OD 10-32 x 1/2 Set Screw Screw 8-32 x 3/8 Zinc MODEL 370 SS SAPPHIRE SCIENTIFIC...
- Page 53 Hose Identification MODEL 370 SS SAPPHIRE SCIENTIFIC...
- Page 54 5-11 69-191 ASSY, WATER BOX MODEL 370 SS 61-454 ASSEMBLY, WATER BOX 58-375 BRACKET,WATER BOX MOUNTING LEFT SIDE 58-376 BRACKET,WATER BOX RS 61-461 ASSEMBLY, FINNED TUBE COIL 60-401 PLATE, MOUNTING, COIL MANIFOLD 66-217 BLOCK, COIL MANIFOLD OUTLET 66-218 BLOCK, COIL MANIFOLD INLET...
- Page 55 BOLT, 1/4-20 X 3 SHCS 21-076 BUSHING, 1/4 M X 1/8 F BRASS 21-011 ELL, 1/8 P X 1/4 POLY BR 63-107 ASSY,SILENCER 270-370 SS 16-052 HOSE, 3" HIGH TEMP EXHAUST 69-198 ASSY, FLOAT VALVE 21-315 NIPPLE, 3-8 NPT X 5IN SS.IGS...
- Page 56 NUT, FLOAT VALVE MOUNTING 28-008 BALL, 5/16 HARDENED SS 41-072 O-RING, 11/16 X 7/8 VITON, AS568A #115 61-499 WELDMENT, FLOAT VALVE LEVER 10-148 SCREW, SHOULDER, 8-32 X Ø3/16 X 1.0L SOCHD SS 11-067 NUT, 8-32 HEX LOCK, SS MODEL 370 SS SAPPHIRE SCIENTIFIC...
- Page 57 5-12 ASSY, WATER PUMP MODEL 370 SS Item No. Part Number Description 46-051 PUMP,CAT 3CP1120S.3 HOT&DRY 35-001 CLUTCH, ELECT CAT3CP 16.5MM 61-450 3CP1120 Cat Pump Mounting Bracket 61-449 ASSY, MOUNTING PLATE 3CP CAT PUMP 10-010 SCREW, MACH 3/8-16 X 4 ALLTHRD...
- Page 58 11-005 NUT, 5/16-18 ZINC MODEL 370 SS SAPPHIRE SCIENTIFIC...
- Page 59 HOSE, 1/2 X 10 1/2FT X 1/2FT W/CVR 21-001 CONN, 1/8 P X 1/4 T BR 18-018 HOSE, 3/16 X 10 1/4FT X 1/4FT 16-017 TUBING, IMPOLENE 250FT. 21-090 ELL, 1/8 FP X 1/8 FP MODEL 370 SS SAPPHIRE SCIENTIFIC...
- Page 60 HOSE ASSEMBLY, 1/2 DIA X 1/2 FJIC X 1/2 FJIC X 18.0 L 18-214-04 W/SLEEVE 21-336 TEE, 1/8 P X 1/4 JIC X 1/4 JIC BR 18-215-10 HOSE ASSEMBLY, 3/16 DIA X 1/4 FJIC X 1/4 FJIC X 18.0 L W-CVR MODEL 370 SS SAPPHIRE SCIENTIFIC...
- Page 61 21-029 PLUG, 1/8 SOCKET HEAD 18-215-06 HOSE ASSEMBLY, 3/16 DIA X 1/4 FJIC X 1/4 FJIC X 13.5 L W-CVR 18-215-08 HOSE ASSEMBLY, 3/16 DIA X 1/4 FJIC X 1/4 FJIC X 15.5 L W-CVR MODEL 370 SS SAPPHIRE SCIENTIFIC...
- Page 62 21-073 COUPLING, 3/8 STD BRASS 21-030 NIP, HEX 1/2 X 3/8 BRASS 20-033 FILTER, MICRO INLINE CAT 1-2 F NPT X 1-2 F NPT 21-324 FTTG, 1/2 MNPT X 5/8 HOSE BARB, 45 DEG BRASS MODEL 370 SS SAPPHIRE SCIENTIFIC...
- Page 63 SPRING, VAC RELIEF VALVE 12-021 WASHER, FLAT 7_16 ZINC-1 11-012 NUT, 7_16-14 ZINC 57-006 7.25 ALLTHRD, 5/8-18 57-006 5.25 ALLTHRD, 5/8-18 11-062 NUT, 5/8-11 JAM 5E Nut(Default) 12-039 LKWSR, 5/8 12-040 WASHER, FLAT 5/8 SAE MODEL 370 SS SAPPHIRE SCIENTIFIC...
- Page 64 Item No. Part Number Description 20-002 STRAINER, SUCTION END 1/8FP 21-007 FTTG,BRB 1/8 PX 5/16 H BR 46-056 PUMP, CHEMICAL, GENERAL PUMP 23-028 VLV, BYPASS SS 26-003 FLOWMETER, 1/8P 23-027 VLV, 3-WAY BALL 1/8 FP SS MODEL 370 SS SAPPHIRE SCIENTIFIC...
- Page 65 O-RING, 70 DURO, GP PULSE PUMP 36-355 VALVE CAP 303SST, GP PULSE PUMP 36-356 ASSY, VALVE KIT, GP CHEMICAL PULSE PUMP 36-357 SPACER RING, 303 SST, GP PULSE PUMP 36-358 VALVE CAP, 303 SST, GP PULSE PUMPMP 520196 MODEL 370 SS SAPPHIRE SCIENTIFIC...
- Page 66 44-000 DECAL SHEET, WARNING & CONTROLS 44-073 DECAL, MODEL 370 SS GRILL MODEL 370 SS SAPPHIRE SCIENTIFIC...
- Page 67 OPTIONAL WASTE SWITCH PUMP KIT WASTE GRAY 68-003 PUMP ON SWITCH PUMP,CAT 69-002 3CP1120S.3 HOT&DRY TRANSFER GRN/BLK BLK/WHT PUMP BLACK WHITE SHUT-OFF BLUE SWITCH BLK/WHT 69-000 BLACK WASTE WHITE BROWN PUMP-OUT Sapphire 370 SS Wiring 07-06-09 MODEL 370 SS SAPPHIRE SCIENTIFIC...
- Page 68 STRAINER, WST TNK 2-1/2 IN. 100 M. 69-000 WIRING , LEVEL SENSOR SHUTOFF 21-064 ELL, 1/4 P X 1/4 T BRASS 18-007 HOSE, 3/16 X 44-1/2 1/8 P X 1/4 FT 21-097 PLUG, 1-1/4 IN PVC 19-009 CAP, WASTE TANK INLET MODEL 370 SS SAPPHIRE SCIENTIFIC...
- Page 69 Solution control valve. Turn 45° counter-clockwise to open fully. FIG. B: EXTRACTION HEAD (Bottom view) Purge valve. To flush out or debris from injector, loosen purge valve and allow solution to flow at full force. Injector/extraction. manifold MODEL 370 SS SAPPHIRE SCIENTIFIC...
- Page 70 DSC, 1/4M X 1/4FP BR 23-035 VLV,SPRAYER HYPRO 3381-0032 21-050 CONN, 1/4 P X 1/4 T BRASS 18-021 HOSE, 3/16 X 51 1/4FT X 1/4FT 24-000 TIP, SPRAY 95015X1/8P SST 40-009 HANDLE, ERGO WAND COATED MODEL 370 SS SAPPHIRE SCIENTIFIC...
- Page 71 FTTG, BULKHEAD ¼ IN. BRASS 21-006 FTTG, BRB ¼PX5//16H BR 21-039 ELL, ¼ IN LG STREET BRASS 14-011 CLAMP, HOSE FUEL #6 21-038 ELL, STREET 1/8 IN. BRASS 21-007 FTTG, BRB 1/8 P X 5/16 H BR MODEL 370 SS SAPPHIRE SCIENTIFIC...
- Page 72 FTTG, BULKHEAD 1/4 IN. BRASS 21-006 FTTG, BRB 1/4PX5//16H BR 21-039 ELL, 1/4 IN LG STREET BRASS 14-011 CLAMP, HOSE FUEL #6 21-038 ELL, STREET 1/8 IN. BRASS 21-007 FTTG, BRB 1/8 P X 5/16 H BR MODEL 370 SS SAPPHIRE SCIENTIFIC...
- Page 73 HOSE, 3/16 X 5 1/8P X 1/8P NO CVR 21-006 FTTG, BRB 1/4P X 5/16 H BR 21-039 ELL, 1/4 IN LG STREET BRASS 21-038 ELL, STREET 1/8 IN. BRASS 21-086 FTTG, BULKHEAD 1/4 IN. BRASS MODEL 370 SS SAPPHIRE SCIENTIFIC...
- Page 74 CLAMP, HOSE FUEL #6 21-038 ELL, STREET 1/8 IN. BRASS 21-007 FTTG,BRB 1/8 PX 5/16 H BR 21-039 ELL, 1/4 IN LG STREET BRASS 21-006 FTTG, BRB 1/4PX5//16H BR 21-086 FTTG, BULKHEAD 1/4 IN. BRASS MODEL 370 SS SAPPHIRE SCIENTIFIC...
- Page 75 FTTG,BRB 1/8 PX 5/16 H BR 18-028 HOSE, 3/16 X 25 1/8P X 1/8P NO CVR 21-086 FTTG, BULKHEAD 1/4 IN. BRASS 21-006 1/4 M NPT x 5/16 Hose Barb 21-039 ELL, 1/4 IN LG STREET BRASS MODEL 370 SS SAPPHIRE SCIENTIFIC...
- Page 76 69-033 KIT, 2004 TF ADAPTOR CHEVY 69-033 KIT, 2004 TF ADAPTOR CHEVY MODEL 370 SS SAPPHIRE SCIENTIFIC...
- Page 77 69-047 ADAPTOR, 2004 FUEL FORD MODEL 370 SS SAPPHIRE SCIENTIFIC...
Need help?
Do you have a question about the 370 SS and is the answer not in the manual?
Questions and answers