Table of Contents
Advertisement
Quick Links
16 Channels Bus Switch Board
AL-2010 for SLSC
This document describes the AL-2010 board for National Instruments SLSC-12001 chassis.
Definitions
This document describes the performance of the described module under specific operating
conditions which are covered by the module warranty.
These conditions can be classified into two main sections:
•
Typical specifications describe the performance met by most modules.
•
Nominal specifications describe an attribute that is based on design, conformance
testing, or supplemental testing for this specific module.
Specifications are Typical unless otherwise noted.
ALIARO reserve the right to vary from the description given in this data sheet and shall not be liable for any errors.
www.aliaro.com
Advertisement
Table of Contents
Related Manuals for ALIARO AL-2010
Summary of Contents for ALIARO AL-2010
-
Page 1: Definitions
Nominal specifications describe an attribute that is based on design, conformance testing, or supplemental testing for this specific module. Specifications are Typical unless otherwise noted. ALIARO reserve the right to vary from the description given in this data sheet and shall not be liable for any errors. www.aliaro.com... -
Page 2: Conditions
Hardware-In-the-Loop (HIL) test system. For easy board/system configuration, it is recommended to use the board alongside xMove Configurator. ALIARO reserve the right to vary from the description given in this data sheet and shall not be liable for any errors. www.aliaro.com... -
Page 3: Table Of Contents
Electromagnetic Compatibility Standards ..................16 Environmental Management ........................ 17 Waste Electrical and Electronic Equipment (WEEE) ................17 ALIARO reserve the right to vary from the description given in this data sheet and shall not be liable for any errors. www.aliaro.com... -
Page 4: Description
As shown in the diagram below, the AL-2010 supports four bus channels (B1-B4), each distributed to four DUT outputs. ALIARO reserve the right to vary from the description given in this data sheet and shall not be liable for any errors. www.aliaro.com... - Page 5 Shorting signals between Hi / Lo of the serial lines • Fault insertion outputting Hi or Lo to axillary signals + / – ALIARO reserve the right to vary from the description given in this data sheet and shall not be liable for any errors. www.aliaro.com...
- Page 6 16 DUT interfaces. Each bus can be terminated (120 ohm) at the end by software. ALIARO reserve the right to vary from the description given in this data sheet and shall not be liable for any errors.
-
Page 7: Front Connector Pinout
Shorting signals between Hi / Lo of the serial lines • Fault insertion outputting Hi or Lo to axillary signals + / – Front Connector Pinout ALIARO reserve the right to vary from the description given in this data sheet and shall not be liable for any errors. www.aliaro.com... - Page 8 The AL-2010 has four connectors each consisting of twenty terminals. Figure 5: AL-2010 Front Connector Pinout ALIARO reserve the right to vary from the description given in this data sheet and shall not be liable for any errors. www.aliaro.com...
-
Page 9: Rti Backplane
Figure 6: AL-2010 Backplane The RTI backplane support RJ-45 for Ethernet and Molex connector for the serial bus connections. ALIARO reserve the right to vary from the description given in this data sheet and shall not be liable for any errors. www.aliaro.com... -
Page 10: Installation
What You Need to Get Started To set up and use the module you need the following items: Hardware ALIARO reserve the right to vary from the description given in this data sheet and shall not be liable for any errors. www.aliaro.com... -
Page 11: Installing The Al-2010
RTIs and modules are installed before fully tightening the screws. This ensures the proper alignment for future connections between modules and RTIs. ALIARO reserve the right to vary from the description given in this data sheet and shall not be liable for any errors. www.aliaro.com... -
Page 12: Software Installation - Slsc Labview Drivers
Use the device only with the chassis, modules, accessories, and cables specified in the product specification. ALIARO reserve the right to vary from the description given in this data sheet and shall not be liable for any errors. www.aliaro.com... -
Page 13: System Check Using Labview
Contact ALIARO to schedule calibration services. Additionally, you may be entitled to calibration if you have a service agreement. ALIARO reserve the right to vary from the description given in this data sheet and shall not be liable for any errors. www.aliaro.com... - Page 14 If you have purchased a calibration system from ALIARO, we recommend using the system with your complete ALIARO test system or device, after the specified interval. ALIARO reserve the right to vary from the description given in this data sheet and shall not be liable for any errors. www.aliaro.com...
-
Page 15: Specification
144.32mm x 30.48mm x 281 mm (H x W x D) Weight 300g Front I/O Connector 4 x Phoenix 1844808 20-pins ALIARO reserve the right to vary from the description given in this data sheet and shall not be liable for any errors. www.aliaro.com... -
Page 16: Technical Characteristics
2014/35/EU; Low-Voltage Directive (safety) • 2014/30/EU; Electromagnetic Compatibility Directive (EMC) • 2011/65/EU; Restriction of Hazardous Substances (RoHS) Electromagnetic Compatibility Standards ALIARO reserve the right to vary from the description given in this data sheet and shall not be liable for any errors. www.aliaro.com... -
Page 17: Environmental Management
For more information about how to recycle ALIARO products in your region, visit ALIARO.com/environment/weee ALIARO reserve the right to vary from the description given in this data sheet and shall not be liable for any errors. www.aliaro.com...