Sharp SuperSteam Plus SSC3088AS Service Manual
  1. Manuals
  2. Brands
  3. Sharp Manuals
  4. Oven
  5. SuperSteam Plus SSC3088AS
  6. Service manual

Sharp SuperSteam Plus SSC3088AS Service Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
In the interest of user-safety the oven should be restored to its original condition and only parts identical to those specified should
be used.
WARNING TO SERVICE PERSONNEL: Ovens contain circuitry capable of producing very high voltage and current. Contact
with the following parts may result in a severe, possibly fatal, electrical shock.
PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING ......................................................... 2
BEFORE SERVICING ............................................................................................................................................ 2
WARNING TO SERVICE PERSONNEL ................................................................................................................. 2
FOREWORD AND WARNING ............................................................................................................................... 3
PRODUCT SPECIFICATIONS ............................................................................................................................... 4
OVEN COMPONENTS ........................................................................................................................................... 5
CONTROL PANEL .................................................................................................................................................. 6
SCHEMATIC ........................................................................................................................................................... 7
SUPER STEAM COMPONENTS ........................................................................................................................... 9
TEST PROCEDURES .......................................................................................................................................... 15
HOW TO REPLACE MAIN PARTS ....................................................................................................................... 24
PARTS LIST ........................................................................................................................................................ 40
PACKING AND ACCESSORIES .......................................................................................................................... 60
This document has been published to be used for after sales service only. The contents are subject to change without notice
335 Britannia Road East, Mississauga, Ontario L4Z 1W9
SERvICE MANUAL
MANUAL
BACK
CLEAR
START

TABLE OF CONTENTS

SHARP ELECTRONICS OF CANADA LTD.
(905) 568-7140
Website: www.sharp.ca
1
SUPER STEAM PLUS
OvEN
SSC3088AS
SSC3088AS
SY5M387SSC308
Page
.

Advertisement

Table of Contents
loading

Related Manuals for Sharp SuperSteam Plus SSC3088AS

Summary of Contents for Sharp SuperSteam Plus SSC3088AS

  • Page 1: Table Of Contents

    PACKING AND ACCESSORIES .......................... 60 This document has been published to be used for after sales service only. The contents are subject to change without notice SHARP ELECTRONICS OF CANADA LTD. 335 Britannia Road East, Mississauga, Ontario L4Z 1W9 (905) 568-7140...

  • Page 2: Precautions To Be Observed Before And During Servicing

    SSC3088AS PRECAUTIONS TO BE OBSERvED BEFORE AND DURING SERvICING (a) Do not operate or allow the oven to be operated with the door open. (b) Make the following safety checks on all ovens to be serviced before and/or makeing repairs as nec- essary: (1) interlock operation, (2) proper door closing, (3) seal and sealing surfaces (wear, and other damage), (4) damage to or loosening of hinges and latches, (5) evidence of dropping or abuse.

  • Page 3: Foreword And Warning

    PRODUCT DESCRIPTION SuperSteam Plus Oven SCHEMATICS SSC3088AS FOREWORD TEST PROCEDURE This Manual has been prepared to provide Sharp Electronics Corp. Service Personnel and Service Information for the SUPERSTEAM PLUS OvEN. MICROWAVE DRAWER DISSASSEMBLY AND ADJUSTMENT PROCEDURE It is recommended that service personnel carefully study the entire text of this manual so that they will be qualified to render satisfactory customer service.

  • Page 4: Product Specifications

    SSC3088AS SPECIFICATION ITEM DESCRIPTION Power Requirements 120 Volts 12.04 Amperes 60 Hertz / Single phase, 3 wire grounded Power Output Top Heater - 750 Watts Mid Heater - 600 Watts Rear Heater - 400 Watts Engine Heater - 1350 Watts Convection Power Output 1450 Watts Outside Dimensions...

  • Page 5: Oven Components

    SSC3088AS OvEN COMPONENTS 1 Air vent opening 2 Handle 3 LCD display 4 Control panel 5 Frame 6 Drip tray (see page 11) 7 Reservoir lid (see page 11) 8 Reservoir (see page 11) 9 Oven light 10 Anti-tip stubs 11 Tray guide 12 Upper level 13 Lower level...
  • Page 6 SSC3088AS CONTROL MANUAL PAGE HOME PAGE...

  • Page 7: Schematic

    SSC3088AS SCHEMATIC...
  • Page 8 SSC3088AS SUPER STEAM REMOvAL FROM CABINET 1. Open the drip tray door and remove the 2 shoulder 3. Use a minimum of 2 people to lift and remove oven. bolts/sleeve (Figure 5). Partially remove oven from cabinet and unplug the power supply cord from the electrical outlet (Figure 7).

  • Page 9: Super Steam Components

    SSC3088AS SUPER STEAM COMPONENTS [1] Wiring method of each part ● Latch SWK Black (COM.) Damper SW (exhaust) ● Controlling harness Door SW Black (NO.) Main White/white (COM.) harness (controlling harness) Red (NO.) Main latch SW Damper SW (exhaust) Black/Black (COM.) Black (N.C.) (outside) Oven lamp ●...
  • Page 10 SSC3088AS ●Sirocco motor (left) ● SH Heater (lower), Engine liquid-level sensor , Thermistor (oven) SF heater (lower) engine unit side: Red (main harness) Harness of the sirocco motor (left) SH heater (lower): Blue (main harness) Sirocco motor (left) Thermistor harness (oven) Controlling harness connector (white case) Engine water level sensor...
  • Page 11 SSC3088AS ● AC code Tank SW, and pump motor Tank SW Pump motor connector White/white (COM.) Blue (Housing) Brown (NC.) Main harness connector Bottom plate ● Fan motor Black/black (main harness) AC cord ● White (main harness) Fan motor Wiring on the right side Controlling harness Controlling harness Snap-on fastening position...
  • Page 12 SSC3088AS NOISE FILTER RED (SOURCE) BLUE (SOURCE) 20A FUSE WHITE (LOAD) BLACK (LOAD)
  • Page 13 SSC3088AS CONTROL UNIT (Controlling harness) (Main harness) (Main harness) MOLEX MOLEX CN-P (Controlling harness) Black Black Black Black Black White BLK RED GRY BLK WHT YLW GRY BLU White White White White White Rear plate side Door side CN-B (controlling harness) White Black Gray...
  • Page 14 SSC3088AS Error Code list error display details of error check timing application menu error condition note check item change parts (EEPROM) １．Check the relay welding fermentation ２．Check the oven thermistor １．Change the relay board fermentation mode oven temperature defrost oven temperature is too ３．Check the harness of the CN-B and ２．Chenge the oven thermistor After 1sec.

  • Page 15: Test Procedures

    SSC3088AS TEST PROCEDURES Error record confirmation procedure Power on/door open/close→ [Clear]→ [Manual heating]→ [Start]→ [Start]→ Door open/close operation→ Press the [Back] key 14 times to set the test mode number at 16● [Start] Inspection method when error occurs 1. Inspection method of water supply performance and engine liquid-level sensor performance 1) Confirm the water tank is installed Install the water tank onto the main body and confirm its installation.
  • Page 16 SSC3088AS Set the empty water tank onto the main body Select the test mode 6 (line forced drainage) in the following sequence: Even if drainage is repeated for 5 times, “Clear” → “Manual” → “Start” → “Start” → “Open/Close door” → the level value is no less than 20 “Touch key [6]”...
  • Page 17 SSC3088AS "Message 01" (oven thermistor fault), "Message 05 and Message 12" (engine thermistor fault" Connect or repair The connector of the thermistor ( board part and thermistor part) the connector is not disconnected or short circuited Pull out the thermistor connector from the board, measure the resistance value of the thermistor with a tester or measure the resistance value between both two terminals with a relay connector The resistance value of the thermistor is within normal range at about Replace the thermistor or the harness...
  • Page 18 SSC3088AS Inspection and handling method at the time of abnormal operation [1] List Operation Malfunction How to check ＹＥＳ： Refer to“inspection on 20A fuse blowout” ・Not indicated ・Fuse 20A is blown ＮＯ　： Board connector/ wiring inspection * ＹＥＳ：Replacement of the engine unit ・...
  • Page 19 SSC3088AS Operation Malfunction How to check ・ Contact 08 appears ・The damper shaft of the SH damper (sub-part of oven DK, refer to the photograph on P50) is fluctuating. When heating ＹＥＳ：The damper SW (SH) contact is conducting electricity. ＹＥＳ：Check for any disconnection of the harness going to the started damper SW (SH) or replace the relay board.
  • Page 20 SSC3088AS NOTES...
  • Page 21 SSC3088AS Operation of parts in different cooking methods [1]When powered on When oven is first plugged into AC ● If the dampers’ vents are not in their proper locations, damper motors’ for intake, exhaust and SH rotate for a maximum 10~12 seconds until all three damper SW are in OFF.
  • Page 22 SSC3088AS CONV BAKE or CONV BROIL (PRE-HEAT) *2-HEATER ON/OFF BY OVEN TEMPERATURE SH HEATER (TOP:750W) OPERATE 300℃(ONLY COLD START) / KEEP 10 MIN. AFTER REACH SH HEATER (MID:600W) 300℃ THEN DOWN TO 250℃ AFTER 10MIN. SH HEATER (LOW:400W) ENGINE HEATER (1350W) CYCLE MOTOR *5-100～250℃…80% (CCW)/300℃…80％...
  • Page 23 SSC3088AS STEAM ROAST or STEAM GRILL (PRE-HEAT *2-HEATER ON/OFF BY OVEN TEMPERATURE SH HEATER (TOP:750W) OPERATE 300℃(ONLY COLD START) / KEEP 10 MIN. AFTER REACH SH HEATER (MID:600W) 300℃ / DOWN 250℃ AFTER 10MIN. SH HEATER (LOW:400W) ENGINE HEATER (1350W) BEFORE REACH 50sec.ＯＮ...

  • Page 24: How To Replace Main Parts

    SSC3088AS How to replace the main parts [1] Necessary tools Warning ● Phillips screwdriver Pull out the power plug from the socket ●Round nose plier with side cutter before repair or disassembly. ● Slotted screwdriver (Possibility of electric shock) ● 7mm nut driver Do not get your hand pinched.
  • Page 25 SSC3088AS [7] Motor SW and primary switch SW 1. Remove the cabinet. [3] Reference 2. Remove the harness from the motor SW or the primary latch SW 3. Pull out the motor SW or the primary latch SW while expanding the two claws that retain the motor SW or the primary SW outward at the same time.
  • Page 26 SSC3088AS Note: When hooking the R door cam and the L door cam onto the pin of the door panel DK, twist the pin to check whether the Door frame tip hook part is properly inserted. Carpenter’s square 1. With the door closed, fit the door SPR to the R door cam and the R hinge K as well as the L door cam and the L hinge K respectively.
  • Page 27 SSC3088AS 3. How to install the door cover 3) Remove the F finder glass from the frame. 1) Secure the door packing to the door cover. (Refer to 2 stated Note: Be careful because the F finder glass is fixed into the door frame above) on the lower right with double sided adhesive tape in front view.
  • Page 28 SSC3088AS 1. Remove the air supply duct. (6 screws) Note: It will be removed once the end of the connector is lifted up. 2. Remove the display board cover. Note: When installing the display board cover, please pay attention If this end is raised, to the following three points.
  • Page 29 SSC3088AS 1. Remove the door panel DK. [10] Reference 4. Remove the DC fan motor (door) [11] Reference 2. Remove the DC fan motor (door) [11] Reference 5. Remove the display board. [12] Reference 3. Remove the FPC (flexible printed circuit) coming from the panel 6.
  • Page 30 SSC3088AS parts from deforming. 1. Remove the screws which fix the R hinge K and the L hinge K onto the right heat insulating plate and the left heat insulating plate re- spectively (1 screw each). Screw for R hinge K Screw Heat insulating plate on the left...
  • Page 31 SSC3088AS [17] Rear plate 2) Remove the left/right reinforcing AG and the rear plate. [17] Reference 1. Remove the side cover R, the side cover L, the exhaust cover and 3) Remove the steam tube and the pump tube E from the engine the cabinet.
  • Page 32 SSC3088AS 2) Remove the left/right reinforcing AG and the rear plate. [17] Engine unit Reference Harness of the thermistor (engine) 3) Remove the harness from the D motor (intake) and the damper SW (intake). 4) Remove the harness from the intake duct cover top and the hook of the intake duct top.
  • Page 33 SSC3088AS 1. Remove the connector of the controlling harness from the steam duct side and remove the harness of the sirocco motor (right) from the controlling harness. Bottom plate cover Steam duct Screw 3. Remove the pump tube from the cord holder which is fitted on the bottom plate cover.
  • Page 34 SSC3088AS The circle mark is the position of the screw Bottom plates Reference When removing the bottom plate to replace the following parts, it is necessary to remove the reinforcing AG and the rear plate. ●Relay board ●Fan motor ●Tube pump K or pump motor ●Drip pan SW ●Tank SW In order to remove the bottom plate, first remove the screws (3 screws)
  • Page 35 SSC3088AS [23] Drip pan SW 3. Remove the AC cord. [15] Reference 4. Remove the bottom plate cover. [21] Reference 1. Remove the side cover R, the side cover L, the exhaust cover and 5. Remove the bottom plate. [22] Reference the cabinet.
  • Page 36 SSC3088AS 1) Remove the exhaust duct from the oven DK and remove the hu- 2. Remove the left/right reinforcing AG and the rear plate. [17] Refer- midity sensor. ( Refer to 1. How to remove the humidity sensor) ence 2) Remove the screws (7x) which fix the exhaust duct top to the 3.
  • Page 37 SSC3088AS Screw Lower intake duct Screw Fan motor Fan duct cover When fitting the sirocco fan to the fan motor, please apply bond 10) Remove the harness from the D motor (SH) and the damper SW (SH). (Cemedine Super-X) to the sirocco fan axle hole. Then, align the D cut part of the fan motor axle with the D cut part of 11) Remove the slider MTAG from the rear of the heat insulating the sirocco fan and then insert it.
  • Page 38 SSC3088AS When installing the damper cam, please insert the protruding part Upper spring Screw of the damper cam into the slit of the slider. If it is not inserted firmly, the SH damper embedded in the oven DK will not open/close Spring Stopper normally.
  • Page 39 SSC3088AS 2. How to remove the tank SW 1) Pull out the tank cover bottom (attached to the tank cover top) from the opening of the bottom plate. Connector of pump motor 2) While expanding the claws (2x) which retain the tank SW, re- move the tank SW from the tank cover bottom.

  • Page 40: Parts List

    SSC3088AS PARTS LIST REF. NO. PART NO. DESCRIPTION Q'TY CODE 1-24 QSW-MA168WRZZ SWITCH 1-30 FUNT-A178WRKZ CYCLE UNIT ASSY 1-31 FUNT-A185WRKZ ENGINE UNIT 1-31-1 FH-HZA100WREZ THERMISTOR 1-31-2 RTHM-A149WRZZ SH THERMOSTAT 1-31-3 LX-BZA144WREZ SPECAIL SCREW 1-31-4 XHTWW40P08000 SCREW 1-31-5 XETS740P10000 SCREW 1-34 RLMPTA087WRZZ OVEN LAMP 1-36...
  • Page 41 SSC3088AS PARTS LIST REF. NO. PART NO. DESCRIPTION Q’TY CODE 8-105 PCUS-A360WREZ CUSHION 8-110 MSPRTA285WREZ DOOR SPRING 8-111 PSHEPB778WREZ SHEET 8-222 PFPF-A360WREZ HEAT INSULATION LOWER 8-223 LANGTB388MRP0 THERMO PLATE 8-224 LANGTB371MRP0 INSULATION PLATE LX-BZA148WREZ SPECIAL SCREW XETS740P10000 SCREW XEBS730P08000 SCREW XOTS740P08000 SCREW XNEUW40-32000...
  • Page 42 SSC3088AS...
  • Page 43 SSC3088AS PARTS LIST REF. NO. PART NO. DESCRIPTION Q'TY CODE QSW-MA169WRZZ SWITCH 1-10 RMOTDA248WRZZ TT MOTOR 8-12 MSPRTA228WREZ LATCH SPRING 8-20 NSFTPA050WRFZ INTAKE DAMPER CAM 8-21 NSFTPA052WRFZ SHUTTER SHAFT 8-22 PCOVPA694WRFZ INTAKE DUCT COVER 8-23 PDMP-A011WRFZ INTAKE DAMPER 8-24 PDUC-B304WRFZ INTAKE DUCT 8-25 PSHT-A035WRFZ...
  • Page 44 SSC3088AS...
  • Page 45 SSC3088AS PARTS LIST REF. NO. PART NO. DESCRIPTION Q'TY CODE 1-14 RMOT-A029WRZZ SIROCCO MOTOR 8-34 PCOVPA696WRFZ INTAKE DUCT COVER LOWER 8-35 PDUC-B354WRFZ INTAKE DUCT LOWER 8-71 PCUS-A346WREZ CUSHION LX-BZA148WREZ SCREW XETS740P10000 SCREW 9-11 XEPS740P40000 SCREW...
  • Page 46 SSC3088AS 8-35 8-34 8-71 1-14 9-11...
  • Page 47 SSC3088AS PARTS LIST REF. NO. PART NO. DESCRIPTION Q'TY CODE QSW-MA169WRZZ SWITCH RMOTDA248WRZZ TT MOTOR LANGKB597WRPZ SLIDER MOUNT ANGLE MCAMFA002WRFZ DAMPER CAM LSTPPA353WRFZ SPRING STOPPER MSLIFA002WRPZ SLIDER MSPRDA022WREZ UPPER SPRING MSPRDA023WREZ LOWER SPRING 8-220 RTHM-A117WRE0 THERMO CUT OUT 8-221 LANGTB384MRP0 THERMO CUT OUT BRACKET LX-BZA221WREZ SPECIAL SCREW...
  • Page 48 SSC3088AS 8-220 8-221 9-31 9-30...
  • Page 49 SSC3088AS PARTS LIST REF. NO. PART NO. DESCRIPTION Q'TY CODE 1-15 FPWBFA495WRKZ NOISE FILTER 1-16 RMOT-A029WRZZ SIROCCO MOTOR 8-38 LANGQA903WRPZ NOISE FILTER ANGLE 8-39 PCOVPA698WRFZ STEAM DUCT COVER 8-40 PDUC-B356WRFZ STEAM DUCT 8-41 PGID-A149WRPZ MG AIR GUIDE 8-42 PPAC-A199WREZ STEAM DUCT PAC 8-72 PCUS-A347WREZ CUSHION...
  • Page 50 SSC3088AS 8-102 8-42 8-40 8-114 8-100 8-115 8-113 8-39 9-21 9-23 9-15 9-23 1-15 8-72 8-38 1-16 9-11 8-41...
  • Page 51 SSC3088AS PARTS LIST REF. NO. PART NO. DESCRIPTION Q'TY CODE 1-11 FDTCTA240WRKZ SENSOR ASSY 1-12 QSW-MA169WRZZ SWITCH 1-13 RMOTDA248WRZZ TT MOTOR 8-26 MSPRCA191WREZ EXHAUST DAMPER SP 8-27 NSFTPA047WRFZ EXHAUST DAMPER CAM 8-28 PDMP-A002WRFZ EXHAUST DAMPER 8-29 PDUC-B306WRFZ EXHAUST DUCT UPPER 8-30 PDUC-B307WRFZ EXHAUST DUCT LOWER...
  • Page 52 SSC3088AS 9-10 8-42 8-29 8-225 8-32 8-31 8-26 8-27 8-28 1-13 1-12 8-30 9-10 8-106 8-85...
  • Page 53 SSC3088AS PARTS LIST REF. NO. PART NO. DESCRIPTION Q'TY CODE 1-19 DPWB-B004MRU0 CONTROL UNIT 1-22 RMOTEA513WRZZ FAN MOTOR 1-23 QSW-MA169WRZZ SWITCH 1-40 DPWB-B383DRKZ POWER UNIT 8-12 MSPRTA228WREZ LATCH SPRING 8-19 NFANSA011WRFZ 8-46 PCOVPA695WRFZ FAN DUCT COVER 8-47 PDUC-B353WRFZ FAN DUCT 8-48 LHLD-A386WRFZ SWITCH HOLDER...
  • Page 54 SSC3088AS 8-76 8-58 8-59 8-226 8-226 8-48 8-49 9-27 1-23 8-56 8-12 8-47 1-19 9-23 8-19 9-17 9-22 9-22 8-62 8-46 9-22 9-17 9-17 1-22 8-227 1-40 8-228 8-57 8-74...
  • Page 55 SSC3088AS PARTS LIST REF. NO. PART NO. DESCRIPTION Q'TY CODE QSW-MA169WRZZ SWITCH FMOT-A060WRKZ TUBE PUMP ASSY 1-8-1 RMOTDA331WRZZ PUMP MOTOR 1-8-2 XHPS740P08K00 SCREW 1-8-3 PTUBXA095WREZ PUMP TUBE 1-8-4 PTUBXA096WREZ PUMP TUBE 1-27 FW-VZB387MRE0 MAIN HARNESS 1-28 FW-VZB388MRE0 CONTROL HARNESS 1-32 FACCDB015MRE0 POWER SUPPLY CORD GDAI-A538WRWZ...
  • Page 56 SSC3088AS...
  • Page 57 SSC3088AS PARTS LIST REF. NO. PART NO. DESCRIPTION Q'TY CODE FCOV-B545MRK0 DOOR ASSY FHNDPB025MRK0 HANDLE ASSY FDORFA526WREZ DOOR PANEL ASSY GCOVHA572WRFZ DOOR COVER LANGKB599WRWZ DOOR SUPPORT ANGLE PPAC-A191WREZ DOOR PACKING XEPS740P16000 SCREW XWHS740-05100 SCREW/WASHER XETS740P12000 SCREW...
  • Page 58 SSC3088AS...
  • Page 59 SSC3088AS PARTS LIST REF. NO. PART NO. DESCRIPTION Q'TY CODE 90-1 FDECAB222MRK0 BIK MOUNT 90-6 PSRA-A089WRHZ BASE TRAY 90-13 TINSKB206MRR0 OPERATION MANUAL 90-14 UAMI-A184WRTZ RACK 90-15 UGLV-A018WRKZ MITTENS 90-16 TINSKB207MRR1 INSTALATION MANUAL 9-32 LX-CZB069MRE0 MOUNTING BOLTS 9-33 LANGTB372MRT0 LEFT MOUNTING BRACKET 9-34 LANGTB378MRT0 RIGHT MOUNTING BRACKET...

  • Page 60: Packing And Accessories

    SSC3088AS COPYRIGHT © 2015 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in retrieval systems, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.

Table of Contents