Stealth Cam QV Series Manual

Also See for QV Series:

Instruction manual (30 pages)

Table of Contents

Contents

1 About Your Camera
2 Quick Setup Guide
3 Camera Overview
4 Camera Setup
5 Camera Configuration
6 Viewing and Deleting Images
7 Frequently Asked Questions
8 Camera Care
9 Contact Us
10 Documents / Resources
- 10.1 References
- 10.2 Download manual

Stealth Cam QV Series Manual

About Your Camera

Notice: To ensure the product is being utilized to its full potential, we recommend checking our website for new product updates. If your camera is having an issue, please check our website to determine you are using the latest firmware or software version.

Water Resistant Design
Your camera is safe against the elements with a sturdy waterproof housing.

Quick Set Options
Set up in seconds with pre-programmed options.

Burst Rapid-Fire Mode
Rapid-fire Burst Mode, multiple exposures per triggering.

No Glow IR LEDs
Perfectly illuminate your nighttime photos with 24 IR LED lights.

Expandable Storage Space
Expand your storage space with an SC memory card up to 32 GB.

Energy Efficient Design
Completely re-energized to optimize energy efficiency.

Quick Setup Guide

Insert Batteries and SD Card
Install 8 AA batteries and a class 10 SD card into camera.

Mount Camera
Mount the camera at the desired location using the strap mount, Python Lock cable, Articulating Ball Joint Mount, or other desired mounting mechanism. Position the camera so that it does not face East or West directly as the rising and setting of the sun can cause false positive triggers.

Activate Camera
Set camera to "On" position and place in desired vantage point to start capturing photos of game.

Camera Overview

Camera Overview - Part 1

Camera Overview - Part 2

Camera Setup

Battery Installation
To remove batteries from unit, simply open the camera and slide the battery release switch to the left. Once the battery compartment is open, insert SD Card Slot batteries into camera, being careful to match the orientation marked on your camera. After batteries are inserted, close the battery compartment and secure the battery release switch.
Camera Setup

SD Card Installation
SD card slot is located on the bottom of the camera, above the battery compartment. Insert SD card with the label facing back of camera. Only minimal resistance should be felt as card is inserted and a click when the card is fully inserted.

Camera Configuration

Cycle between camera modes by pressing the UP and DOWN arrows. The camera mode will be displayed on the left side of the LCD Screen. This camera comes equipped with two Quick Sets (QSET) containing some of our most popular configurations. QSET 1 and 2 are defined in the table below. For alternate configurations, press the UP or DOWN arrows until CUSTOM is displayed on the left of the LCD screen and press ENTER.

Name	Type	Quality	Timeout Delay	Detail
QSET 1	Photo	Medium	30 sec	1 Photos
QSET 2	Video	Medium	30 sec	10 sec Video

Continue to next page for more information regarding each setting.

DATE: This setting is used by the camera to display the correct date on the Info Bar of the image.

TIME: This setting is used by the camera to display the correct time of day on the Info Bar of the image.

OPERATION MODE: The operation mode setting is accessible immediately after the Time setting. The screen will be blank with either Video or Photo displayed on the right side of screen.
Press Enter to change between Photo and Video mode.

PHOTO: In this mode the camera will take a photo when trigger is activated.

PHOTO BURST: This setting determines how many photos are taken each time the camera is activated.
OPTIONS: 1 photo – 3 photos

PIR DELAY: This setting is used to determine how long the camera will wait before restarting the PIR sensor after taking a photo.
OPTIONS: 5 sec | 10 sec | 15 sec | 30 sec | 60 sec| 120 sec

RESOLUTION: This setting will determine the quality of each image. A higher quality will result in better photos and take more memory space.

OPTIONS: High | Med | Low
Note: This setting is only applicable in photo mode.

VIDEO: In this mode the camera will take a VIDEO when trigger is activated.

VIDEO LENGTH: This setting is used to determine the length of time, in seconds, of a video recording

OPTIONS: 5 sec | 10 sec | 15 sec | 30 sec

PIR DELAY: This setting is used to determine how long the camera will wait before restarting the PIR sensor after taking a video.
OPTIONS: 5 sec | 10 sec | 15 sec | 30 sec | 60 sec| 120 sec

Viewing and Deleting Images

There are a few methods for viewing and deleting your files.

Using an SD Memory Card Reader/Viewer: You will simply need to remove the SD card from the camera and insert it into the reader to view the files; you can also delete them from this device.
Using your computer: This method requires an SD card slot to be installed to your computer. Please refer to your computer's Owner's Manual for the proper way of viewing the files.
Obtain a mobile device adapter: This will allow you to plug one end into the device, and, at the other end, insert the SD card. Please refer to the vendor's User Manual for the proper way of viewing the files.

Frequently Asked Questions

Q: Will I lose my images and settings if the batteries die?
A: You will lose your settings but not your images. The images are stored on your external SD memory card so your images will be intact only on your card.

Q: Why is my camera taking pictures with nothing in front of it?
A: This camera is powered by motion activation. This can cause objects, like a tree branch or moving water, within the camera frame to cause the camera to take a photo.

Q: Is there a warranty that comes with my camera or an extended warranty I can purchase?
A: Your Stealth Cam Camera comes with a Limited 1-year warranty. Please contact support at 1.877.269.8490 for more information.

Q: Can I mix batteries together?
A: No, you should never mix batteries. After your camera batteries die, always install brand new batteries in your camera.

Q: Can I use rechargeable batteries in the camera?
A: Rechargeable batteries can be used but will cause battery percentage to be reported incorrectly.

Camera Care

Operating Conditions
This camera is designed to function in 14°F – 104°F (-10°C - 40°C) 20%-85% relative humidity, non-condensing.

Product Care

When not in use, store camera in a cool, dust-free, environment.
Handle camera with care.
Camera is weather resistant only. Do not fully submerge camera in water or other liquid. Doing so will void camera warranty.
Only use same type of batteries to power camera. Do not mix old and new batteries.
Do not touch camera lens directly. Clean only with soft lens cloth.
Use damp cloth to clean. DO NOT submerge camera.
Remove batteries when camera is not in use for an extended time.
Do not open camera housing to access internal parts. Doing so could damage camera and void warranty.

Notice: Camera is an active electronic device. Attempting to service internal parts may expose you to dangerous voltages and other risks.