Advertisement
Available languages
Available languages
1. Verify the packed contents
Verify the packed contents with the part list given below and ensure that all the components and parts are present.
Also, check that each item is undamaged. If a component or part is missing or damaged, contact your dealer.
1
2
3
4
2. User's manual and RDX Utility
User's Manual and RDX Utility is available in website.
Refer to the user 's manual for RDX Utility installation.
http://www.nec.com/express/
To operate the Internal RDX Drive correctly, observe the following points.
・Disk mode is setted removable mode. Please change the disk mode by RDX utility, if you need the fixed
disk mode. Please refer to the user's guide.
・Please refer to the user's guide for the notes of the backup.
・This product is a removable disk drive. Please use it for the data backup.
・Data cartridges are consumables. Do not continue to use any cartridge in which an error occurs and replace it with a
new one.
・If a data cartridge is subject to a shock, save the data in the cartridge as soon as possible and replace it with a new
one.
・Use data cartridges authorized by NEC for the Internal RDX Drive.
・When storing data cartridges for an extended period of time, data should be read periodically in order to ensure that
restoration from backup data is possible at all times.
Part name
Qty
1
Internal RDX Drive
1
2
DC Power Cable
1
3
Screw
4
4
Startup Guide (this manual)
1
3. Mounting on the Server
The procedure for installing the drive in a server is as follows.
To install in device expansion unit (N8141-69F), refer to the device
expansion unit's user's manual.
To install in server, refer to the server user's manual. An accessory screw
of fig1 is used.
(1) Install the Internal RDX Drive in Fig.2.
Some servers require bracket or other latching rails to
be used. For details on how to install these parts, refer
to the server's operating manual.
(2) Connect the 10-pin connector of INT USB interface cable to the USB connector on mother board.
・When using the rails with the Internal RDX Drive, use the screw holes in the
front cover illustrated in Fig. 1 (see Fig. 2). (Perform the same operation on
the opposite side. Secure two screws on each side, four screws total.)
・In some cases, the rails may extend all the way to the front cover molding.
This causes no problems. When using the rails, adjust their mounting
positions so that the front cover of the Built-In RDX is aligned with the front
covers of other standard components such as the DVD drive Fig. 3). (The
shape of the rails varies according to the model of the server.) For some
servers, the covers are not aligned with each other. However, this does not
cause any problem to occur.
・For some servers, front side of the RDX cartridges may interfere with the
front cover of the server at the time of ejecting cartridge. If the mounting
position can be adjusted with a server rail, please slide into the inside and
mount the device to avoid contact. If the mounting position can not be
adjusted with a server rail, please adjust a position in the bracket adjustable
screw on the right and left side of the device.
・Always use the screws that are provided with the Internal RDX Drive. The screws that are provided with the
Internal RDX Drive are metric screws (length: 3.0 mm). Using screws that are longer than the screws that are
provided with the Internal RDX Drive could result in damage to the Internal RDX Drive.
However, use the screws provided with the server if specified. Also, you may be required to use screws coming
with the server. Refer to the User's Guide of the server.
(3) Connect the DC power attached with the Internal RDX Drive, and USB cables which is specified,
to the server as shown in the figure below. Refer to the User's Guide of the server for USB cables.
Connect the DC power and USB cables in the order.
(4) After connecting the USB cable, bundle the cable so that it does not interfere with the other devices
or fan.
(5) Attach the front cover to the server. Plug the power cable to the outlet.
(6) Turn on the server.
Regulatory Notices
FCC Statement
Note: This equipment has been tested andfound to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
■ Reorient or relocate the receiving antenna.
■ Increase the separation between the equipment and receiver.
■ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
■ Consult the dealer or an experienced radio/TV technician for help.
Industry Canada Class B Emission Compliance Statement/Avis de conformité à la réglementation d'Industrie Canada：
CAN ICES-3(B)/NMB-3(B)
CE
Importer EU Contact :NEC Nederland B.V. Olympia 4, 1213 NT Hilversum, The Netherlands
KC
기 종 별
B 급기기
이 기기는 가정용(B 급) 전자파적합기기로서 주로 가정에서 사용하는 것을 목적으로 하며, 모든지역에서
(가정용방송통신기자재)
사용할 수 있습니다.
This product, is supplied, warranted and supported by NEC. NEC's warranty and support terms and conditions, contact points and procedures
take precedence over those of HPE. Per EU Decision 768/2008/EC, HPE is the manufacturer of record.
Fig.1
Fig.2
사 용 자 안 내 문
Advertisement
