Conair CLS1 - Fabric Shaver and Lint Remover Manual

Conair CLS1 - Fabric Shaver and Lint Remover Manual

Advertisement

Conair CLS1 - Fabric Shaver and Lint Remover Manual

GETTING TO KNOW YOUR FABRIC SHAVER

GETTING TO KNOW YOUR FABRIC SHAVER - Overview

IMPORTANT SAFETY INSTRUCTIONS

THE APPLIANCE MUST NOT COME INTO CONTACT WITH WATER.
DO NOT USE ON DAMP TEXTILES!

The fabric defuzzer might damage structured textiles or very soft materials such as Angora wool. Always test on an area that is not visible on the item you want to treat. In testing, set the distance ring to the highest level.

OPERATING INSTRUCTIONS

  1. Put the item you want to treat on an evensurface.
  2. Turn the distance ring to the appropriate position or remove the ring entirely depending on the distance required.
  3. Switch the unit ON.
  4. Without applying pressure, run the shaverhead lightly over the parts you wish to remove the fuzz from. Fuzz will accumulate in the fuzz collector.
  5. After use, switch the unit OFF.


Empty the fuzz collector regularly and before it becomes overfilled, which can cause the unit to slow down or stop. If unit slows or stops, check and empty fuzz collector prior to replacing the batteries.

REMOVING AND FITTING THE DISTANCE RING

Instructions - REMOVING THE DISTANCE RING
TO REMOVE: Grasp both sides of the ring and pull it off the unit in the direction of the arrow.
Instructions - FITTING THE DISTANCE RING
TO FIT: Push the distance ring onto the unit so that the recess on the distance ring engages the lug on the body of the shaver. This ensures that the distance ring does not twist when you adjust it.

EMPTYING THE FUZZ COLLECTOR

Instructions - EMPTYING THE FUZZ COLLECTOR
Slide the fuzz collector downward and out of the unit.
Empty the collector and slide it straight into the unit until it engages audibly.

CLEANING THE FABRIC DEFUZZER AND SHAVER HEAD

  1. Remove the batteries from the appliance.
  2. Remove the distance ring and turn theshaver head counterclockwise to remove it.
    Cleaning - Part 1
  3. B rush out residual fuzz with any small cleaning brush.

    Blades are extremely sharp and can be damaged easily.
  4. Reattach the shaver head and fit the distance ring.
    If necessary, wipe off the unit casing with a slightly dampened cloth.
    Cleaning - Part 2

INSERTING BATTERIES

Open the battery compartment by sliding the mark on the battery compartment lid against the marking arrow on the handle to and lift it off. Insert the two (2) AA batteries (not included) so that the +/- terminals on each battery match the markings in the battery compartment. Place the battery cover back on and then turn it in the direction of until it engages audibly.
Instructions - Inserting batteries

INSTRUCTIONS FOR USING BATTERIES

  • Always purchase the correct size and gradeof battery most suitable for the intended use.
  • Replace all batteries at the same time.
  • Do not mix old and new batteries.
  • Do not mix alkaline, standard (carbon-zinc)or rechargeable (nickel-cadmium) batteries.
  • Clean the battery contacts as well as thoseof the device prior to battery installation.
  • Ensure that the batteries are installedcorrectly with regard to polarity (+ and -).
  • Remove batteries from equipment that isnot to be used for an extended period of time.
  • Remove depleted batteries promptly.

DISPOSAL OF BATTERIES

When replacing the batteries, make sure you dispose of the old batteries in accordance with applicable regulations. They should be disposed of in a location specifically designated for that purpose so they can be recycled safely without posing any risk to the environment. Do not burn or bury them.

LIMITED ONE-YEAR WARRANTY

Conair will repair or replace (at our option) your unit free of charge for 12 months from the date of purchase if the appliance is defective in workmanship or materials.

ANY IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCJANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHAll BE LIMITED IN DURATION TO THE 12-MONTH DURATION OF THIS WRITTEN, LIMITED WARRANTY.

IN NO EVENT SHAll CONAIR BE ABLE FOR ANY SPECIAL, INCIDENTAl, OR CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, WHATSOEVER.

For information on any Conair products, call 1-800-3-CONAIR or visit us on the web at www.conair.com
Please register this product at: www.conair.com/registration

©2012 Conair Corporation East Windsor, NJ 08520
Glendale, AZ 85307
Made in China

Documents / Resources

References

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Conair CLS1 - Fabric Shaver and Lint Remover Manual

Advertisement

Need help?

Need help?

Do you have a question about the CLS1 and is the answer not in the manual?

Questions and answers

Table of Contents