Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Kenner KNL100E-01
Summary of Contents for Kenner KNL100E-01
- Page 1 VER 19b...
-
Page 2: Table Of Contents
Table of Contents Safety Installation Information .......................... 1 Parts List ................................3 Optional Accessories Parts List........................4 Tools Needed: ..............................4 Technical Specifications & Features ........................ 5 Installation Overview ............................6 Preparation for Installation ..........................7 Install the Gate Opener on the Gate ........................ 7 Mounting of the control box ..........................11 Connection of the Power Supply ........................11 Connection of the control board ........................ -
Page 3: Safety Installation Information
a separate pedestrian access. Safety Installation Information For an installation utilizing non-contact sensors 1. READ and FOLLOW all instruction. (safety sensors), see product manual on the The gate opener is intended for use with Class I placement of non-contact sensors (safety sensors) for vehicular swing gates. - Page 4 13. To AVOID damaging gas, power, or other underground utility lines, contact underground utility locating companies BEFORE digging. SAVE INSTRUCTION. 14. Do not permit children to play on or around the gate and keep all controls out of their reach.
-
Page 5: Parts List
Parts List... -
Page 8: Installation Overview
Installation Overview... -
Page 9: Preparation For Installation
Preparation for Installation There are two installation types for the gate opener, Pull-to-Open and Push-to-Open. Our gate opener is designed for Pull-to-Open, in the Push-to-Open installation, please purchase Push-To-Open Bracket from your supplier. NOTE: Ensure the gate does not open into public areas. The gate opener is mounted to the gate and to the gate post. - Page 11 5. Make sure there is a minimum clearance of 2.5cm between the gate and the opener and that the opener and the Post Pivot Bracket are not binding in both the gate-open and gate-closed positions. If there is not at least 2.5cm of clearance or if the opener and the Post Pivot Bracket are binding, rotate the Post Pivot Bracket and/or move the Post Bracket Assembly to obtain the minimum clearance and eliminate the binding.
-
Page 13: Mounting Of The Control Box
12. Open the release hole plug on the top of the gate opener, insert the release key, and turn the key 90° Open the release hole plug on the top of the gate opener, insert the release key, and turn the key 90° Open the release hole plug on the top of the gate opener, insert the release key, and turn the key 90°... - Page 14 Please note that the wire connection of the power supply syste Please note that the wire connection of the power supply system is very important. Incorrect wire m is very important. Incorrect wire connection will damage the control board. connection will damage the control board. WARNING: NEVER connect the gate opener to the power outlet before all the installations have been WARNING: NEVER connect the gate opener to the power outlet before all the installations have been WARNING: NEVER connect the gate opener to the power outlet before all the installations have been...
- Page 15 3. Use the batteries as the power source and only use the solar panel to charge the batteries If you only use the solar panel to charge the batteries, please note the power of the solar panel should be at least 20W.
-
Page 16: Connection Of The Control Board
batteries, this alternative save costs and is strongly recommended. The positive output of the 24VDC power supply should be wired to the BAT+ (#11) terminal, the negative output should be wired to “BAT-” (#12) terminal. There is no need to use the adapter in this situation. Connection of the control board... - Page 17 1. Actuator Insert the stripped cable wires into the appropriate terminals on the opener terminals block. The red wire should be inserted into the “ +MOTOR” terminal(#17), the black wire into “ MOTOR-” terminal (#18), the blue wire into “ DLMT” terminal(#19), the green wire into “ COM” terminal(#20), and the yellow wire into “ ULMT” terminal (#21).
- Page 18 4. Alarm Lamp (optional) The red wire of the alarm lamp should be inserted into either LAMP (#15) terminal, the white wire into the other one (#16). 5-1. Photocell Beam System (PBS) (optional) Use a 2-core cable to connect the “ + ~” terminal of the photocell emitter to the “+24” (#1) terminal, the “ - ~” terminal to the “GND”...
-
Page 19: How To Program The Remote To The Opener
10. Wired Keypad (optional) The RED wire of the wired keypad should be connected into the “#11” terminal. The BLACK wire of the wired keypad should be connected into the “#5” terminal. The PURPLE wire of the wired keypad should be connected into the “#5” terminal. The BLUE wire of the wired keypad should be connected into the “#4”... -
Page 20: How To Erase All The Remote Codes
How to Erase All the Remote Codes Press and hold the CODE SW button until the CODE LED from ON to OFF. Now all remote codes have been erased. How to use the remote to operate your gate opener Each remote has four buttons, they are A, B, C and D. You may use this remote to operate as many as 4 sets our swing gate opener or 1 set our sliding gate opener and 2 sets our swing gate opener. -
Page 21: Adjusting The Limit Switch
programming. Adjusting the Limit Switch The position of Limit Switch A was fixed in factory, do not adjust it again. Plug on the power to running gate opener, use a screwdriver to loosen the screw of Limit Switch B, slide Limit Switch B to the desired closed position and fix it. -
Page 22: Trouble Shooting
Factory default setting is OFF. DIP Switch #2: Auto close function enabled/disabled ON – Auto close function enabled OFF – Auto close function disabled Set the switch #2 to ON to enable the auto close function. Factory default setting is OFF. DIP Switch #3: Photocell function enabled/disabled ON –... - Page 23 The opener does not run. Power LED flash rapidly (the LED is ON 1. Battery is over-discharged. Check the voltage of the battery. The voltage 200ms per second, of the battery should above 22V to make the gate opener work normally. normally the LED ON 500ms per second).
- Page 24 ©2019-2021 KENNER All Rights Reserved...
Need help?
Do you have a question about the KNL100E-01 and is the answer not in the manual?
Questions and answers
Hello my gate is only operating at 88 degrees . causing high pressure to the closing point. How should i tackle this problem.