1. Manuals
  2. Brands
  3. DIAMOND PACIFIC Manuals
  4. Grinder
  5. Genie
  6. Manual

DIAMOND PACIFIC Genie Manual

Hide thumbs

Advertisement

Table of Contents

Genie
Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Genie and is the answer not in the manual?

Questions and answers

will webber
March 7, 2025

run capacitor wiring

0
william webber
March 11, 2025

capacitor wiring for genie cab motor

0

Summary of Contents for DIAMOND PACIFIC Genie

  • Page 1 Genie Manual...
  • Page 2 DIAMOND WHEELS PIXIE COLLECTION GENIE COLLECTION TITAN COLLECTION CABBING SUPPLIES CARVING SUPPLIES...
  • Page 3 Before plugging in this machine, make certain the electrical outlet is properly grounded and of the proper voltage. Since the Genie uses water as a coolant your electrical circuit should also be protected by a Ground Fault Circuit Interrupter (GFCI) to prevent the possibility of electrical shock.
  • Page 4 Since the grinding and polishing wheels do not require large amounts the bearings, it has high temperature insulation which allows it to of water, the Genie is also a clean operating unit, and can be used in operate at higher temperatures than fan cooled motors. The motor any convenient place such as the kitchen.

  • Page 5: Operation

    Nova discs attached to the right hand side of your to steady your hands while grinding and polishing. Usually it will be laid Genie, or laps having a ½" center hole attached to the left hand flat in the pan.

  • Page 6: Use And Maintenance

    Description: 5. A few drops of Water Aid in the pan will improve the cutting ability of the Galaxy Wheels. Galaxy metal-bond diamond grinding wheels are designed to provide the gem-cutter with a smooth, fast cutting, true-running grinding Reverse the wheels occasionally so that the diamonds cut from the surface ideal for working stones.
  • Page 7 depress slightly to conform to your stone. This eliminates the flat Since most gem material comes in sizes and shapes larger than desired for a single cabochon, it must be pre-formed. This is usually spots left by the grinding wheels and will cause fewer scratches done by cutting the rock into slabs about 1/4 inch thick with a lapidary than would be produced by pressure that is too light.
  • Page 8 oscillatory manner so that its point of contact with the wheel spirals from possible at each stage before going on to the next, as the finer grit the edge of the stone to the center and back without stopping, since wheels take longer to remove scratches than do the coarser grit stopping produces a flat spot.

  • Page 9: Optional Accessories

    A trim saw attachment is available that can be mounted on the right these laps hand side of the Genie. The saw comes with an eight inch blade and grinding and polishing flat uses water as a coolant, so that it can be used wherever your Genie surfaces.
  • Page 10 Genie. Using an extra right hand adaptor and spacers allows the gem carver to mount the wheels just four at a time as shown below. The two sets of Novas can be interchanged on the right side of the machine in about 20 seconds and the space between wheels will be 3"...

  • Page 11: Pump Maintenance

    Extra right hand adaptors are also used for mounting extra grits in Nova Pump Maintenance or Galaxy wheels or special shaped wheels such as our Convex Carving wheels. Wheels can even be mounted one at a time for even Oiling Pump Leathers and Bearings: more working room.
  • Page 12 top where the screw was removed. Do not use too much oil or allow it Place the felt between the two leathers. The smooth or shiny to run out of the hole, as excess oil can leak onto the pump belt and side of the leathers should be away from the felt.
  • Page 13 The standard wheels on the left hand side of the Genie are two either by holding Galaxy metal-bond wheels (80 and 220 grits) and one 280 grit Nova it by hand or by resin-bond wheel.
  • Page 14 Start with the inside wheel which is usually the 280 Nova. Loosen The left hand set of wheels can also be removed as a unit while still the brass lap connector and rotate the inside wheel about one mounted on the adaptor if necessary. This can be done as follows: eighth of a turn.

  • Page 15: Parts And Accessories

    Parts and Accessories Genie Trim Saw Attachment 100-TSG-105 Orders/Technical Support: Replacement Trim Saw Blade 100-TSB-106 Jewelers Buff Kit 100-JBK-G Toll Free: (800)253-2954 The Boxer 100-BOXER Right Hand Adaptor Kit 101-ADP-GRK (includes 7 spacers) Outside US: (760)255-1030 Extra Right Hand Adaptor...

Table of Contents

Save PDF