Muse MT-108 BT - Turntable Stereo System Manual

LOCATION AND DESCRIPTION CONTROLS

1. Lift lever
2. Tom arm
3. Speed selector (33/45/78)
4. AUTO STOP (ON/OFF) switch
5. Tone arm rest
6. Cartridge with stylus
7. MODE selector: To select BT (BLUETOOTH), PH (PHONO), USB mode
8. POWER ON/OFF and volume control (MIN/MAX)
9. PITCH knob (to adjust the speed of platter)
10. 45 RPM adaptor
11. Platter
12. DC IN 12V JACK
13. Speaker output jacks (Left / Right)
14. Speaker box
15. USB port
16. BACK button
17. REC / : RECORD, PLAY/ PAUSE button
18. SPLIT/ : Segmented record, next button
19. Mode indicator

POWER SUPPLY

Using the AC adaptor

AC adaptor:
Input 100-240V 50/60Hz, 0.8A
Output 12V 2000mA

The supplied AC adaptor is suitable for use on AC main supplies of 100-240V AC and should only be connected to a mains supply within these parameters.

In a concern of saving energy, when playback has reached to the end or listening volume is set at a very low level and no control is operated on the device for a period of 15 minutes, the unit will automatically switch to Standby mode.

• The included AC adapter is exclusively intended to be used with this device.
• Turn off the power before unplugging the AC adapter to avoid damaging the device.
• In case of unused for long periods, unplug the AC adapter from the outlet.
• Place the unit near the outlet and make sure it is easily accessible. If a malfunction occurs, immediately disconnect the unit from the wall outlet.
• The adapter enables you to unplug the unit. It must be easily accessible during use.
• To completely turn off power, unplug the adapter from the wall outlet.
• Never use a damaged power adapter. Place the power cord safely and so that you do not pinch or crush it. If the cable is damaged, contact a repair service.

SPEAKER CONNECTION

Plug the RIGHT / LEFT speakers' cord into the speaker output sockets at the rear of the unit.

TURN ON / OFF THE UNIT

1. To turn the unit on, rotate the POWER ON/OFF switch clockwise until a "click" is heard and set the volume (MIN/MAX) to a lower level.
2. When you have finished the unit, rotate the POWER ON/OFF switch counter-clockwise until a "click" is heard to turn off the unit.

LISTEN TO THE PHONO

1. When the unit is on, set the MODE selector to PH position. indicator becomes red.
2. Remove the stylus cover from the stylus and released the Tone arm rest.
3. Place a record on the turntable platter and select the desired speed (33/45/78) according to the record.
   NOTE: If you are playing 45 RPM singles, place the 45 RPM adapter on the center spindle (45 RPM adaptor is located in the holder near the tone arm).
4. Push up the lift lever to raise the tone arm and gently move the tone arm to the desired position onto the record, Push down the lift lever, the tone arm slowly onto the record to start playing the record.
5. Rotate the PITCH knob to adjust the speed of platter.
6. Adjust the volume control to your desired level.

Noted:

• If the AUTO STOP ON/OFF Switch is turned ON, the record will stop automatically when playback ends. If Auto Stop switch is turned OFF, record will NOT stop automatically when playback ends.
• AUTO STOP function applies to most 33RPM vinyl records. However, even if the AUTO STOP function is ON, it may happen that some vinyl records, e.g. 45RPM, will stop before playback comes to the end OR will not stop automatically when playback comes to the end. If the vinyl record stops before playback comes to the end, set the AUTO STOP switch to "OFF" position. Then playback will continue, but it will not stop automatically.

Do not turn or stop the Turntable platter manually. Moving or jarring the Turntable platter without securing the Tone Arm Clamp could result in damage to the Tone Arm or Stylus.

LISTEN TO THE DEVICE USB

Connect a USB device containing MP3 files or MP3 player to the USB port.

When the unit is on, set the mode selector to USB position, indicator becomes red flashing. The USB start to playback automatically. Press to pause, the indicator keep remain red without flashing.

Adjust the volume (MIN/MAX) to the desired level.

Press to skip forward to the next track or repeatedly to several tracks. Press return to the beginning of the track, or press repeatedly to skip backwards several tracks. Press and hold to search quickly within a track.

Removing the USB device

Please be sure to stop playback and turn the unit OFF before removing the USB device to avoid damage the USB and system.

Note:

• There are many USB devices in the market. We cannot guarantee to support all different models. Please try another USB card device if yours is not supported.
• The unit might not support all the multimedia files stored in USB card because it includes some special playback procedure which might not be compatible with the procedure of this unit.

BLUETOOTH FUNCTION

The Bluetooth^® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by New One S.A.S is under license. Other trademarks and trade names are those of their respective owners.

Pairing a Bluetooth Device

1. When the unit is ON, set the mode selector to BT position. Indicator becomes blue flashing.
2. On the Bluetooth device, enable Bluetooth and select "MUSE MT-108 BT" from the Device List. (Refer to the user manual of the device to be connected for detailed operations.) If the Bluetooth device prompts for a passcode, use "0000". Some Bluetooth devices will ask you to accept the connection. If the units are paired properly, you will hear an indication sound. Bluetooth indicator will keep Blue.

Tip: If you want to connect your Bluetooth speaker to another Bluetooth audio device, press and hold the button to disconnect the device, and then follow the steps above to make a new connection.

• On some devices such as computers, once paired you must select the unit from the Bluetooth menu and choose "Use as Audio Device (stereo)" or similar.
• Pairing remains intact when the unit and/or your Bluetooth device is taken out of communication range. An active connection will be re-established when your Bluetooth device returns within range.
• When the unit is turned on again, it will automatically try to reconnect with the most recently paired Bluetooth device.

Using a Bluetooth Device

1. With a unit paired (see previous section), operate your Bluetooth device and its sound will be heard through the MT-108 BT's speakers.
2. Press the button to pause playback. Press again to resume playback.
3. Select desired track with .
4. Adjust the volume (MIN/MAX) to the desired level. You can also adjust the volume on the device to which you are paired.

Tips on Bluetooth mode

In a concern of saving energy, when the volume level in your Bluetooth device (e.g. smart phone) is set at a low level for a period of 15 minutes, the unit will automatically switch to Standby mode. If this occurs, increase the volume level in your Bluetooth device and use the volume knob on the unit to adjust to your desired sound level if necessary.

RECORDING FROM PHONO TO USB

1. Connect the USB device to the USB port (Make sure the USB device have enough space to save the encoding).
2. Follow procedures 1 to 6 in Listen to the PHONO section.
3. Press REC button, indicator becomes blue and red flashing alternately to start the recording.
4. Press the REC button to stop the recording, indicator becomes red.
5. To listen the recording, set the mode selector to USB position, indicator becomes red flashing, press to find your track and listen your recording.

SPLIT FUNCTION

Press SPLIT button when recording, the current record will be cut off and automatically stored in a file. Press SPLIT button again will generate another file.

NOTE: Press the button to stop the recording.

HOW TO REPLACE THE TURNTABLE STYLUS (NEEDLE)

Removing the Stylus(needle) from the Cartridge

1. Raise the Tone Arm.
   To remove the old stylus needle, Place a screwdriver at the tip of the stylus and push downward as shown in direction "A".
2. Remove the stylus by pulling the stylus forward and pushing downward.

Installing the Stylus

1. Hold the tip of the stylus and insert the stylus by pressing as shown in direction "B".
2. Push the stylus upward as in direction "C" until the stylus locks into the tip position.

TIPS FOR BETTER TURNTABLE PERFORMANCE

1. When opening or closing the turntable cover, handle it gently, gripping it either at the center or at each side.
2. Do not touch the needle tip with your fingers; avoid bumping the needle against the turntable platter or record edge.
3. Frequently clean the needle tip-use a soft brush in a "back-to-front' motion only.
4. If you must use a needle cleaning fluid, use very sparingly.
5. Gently wipe the dust cover and turntable housing with a soft cloth. Use only a small amount of mild detergent to clean the turntable and dust cover.
6. Never apply harsh chemicals or solvents to any part of the turntable system.

Hereby, NEW ONE S.A.S, declares that this MUSE MT-108 BT is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/ EU. The declaration of conformity may be consulted at www.muse-europe.com

SPECIFICATIONS

GENERAL

Power:
AC ADAPTOR: AC IN 100-240V AC, 50/60Hz
Output: DC 12V 2000mA
Output Power: 2 x 8W

BLUETOOTH

Bluetooth Version: 5.1+BR+EDR+BLE
Bluetooth: 2402-2480 MHz
RF Output Power: 4 dBm
Working Distance: Up to 10 meters measured in open space (wall and structures may affect range of device)

Specifications and appearance are subject to change without notice.

MORE INFORMATION

To reduce the risk of electric shock, do not remove the cover (or back). There are no user serviceable parts inside the unit. Refer all servicing to qualify personnel.

The lightening flash with arrowhead symbol within the triangle is a warning sign alerting the user of "dangerous voltage" inside the unit.

The exclamation point within the triangle is a warning sign alerting the user of important instructions accompanying the product.

• The use of apparatus in moderate climates.
• The Marking plate is located on the bottom of the device.
• Make sure to have a minimum distance of 5 cm around the unit for sufficient ventilation.
• Ensure that the ventilation openings is not covered with items such as newspapers, tablecloths, curtains, etc.
• Do not place naked flame sources, such as lighted candles on the apparatus.
• Do not expose this appliance to dripping or splashing water.
• Do not place objects filled with liquids, such as glass, vase on the device
• The power plug is used as a disconnect device and must be easily accessible. To be completely disconnected from the power, the plug of the appliance should be disconnected completely. The socket must not be obstructed and should be easily accessible during intended use.
• Under the influence of fast transient and / or electrostatic electric phenomenon, the product may malfunction and the user must perform a power reset of the device.
• The normal function of the product may be disturbed by strong Electro-Magnetic Interference. If so, simply reset the product to resume normal operation by following the instruction manual. In case the function could not resume, please use the product in other location.

If at any time in the future you should need to dispose of this product please note that Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.(Waste Electrical and Electronic Equipment Directive)