Advertisement
Troubleshooting
Problem
EN
Soleplate is not heating even though iron is
turned on.
Iron does not produce steam.
Spray function does not work.
Steam jet and vertical steam jet function does
not work.
Water leaks from the soleplate during ironing.
Flakes and impurities come out of the soleplate
during ironing.
Water leaks from the soleplate while the iron is
cooling down or after it has been stored.
故障
CNS
熨斗已通电，但底板未加热。
熨斗不产生蒸汽。
喷雾功能不起作用。
蒸汽喷射和垂直蒸汽喷射功能不起作用。
熨烫时底板漏水。
熨烫时从底板上掉下碎末和杂质。
在熨斗冷却时或收好之后底板上漏水。
12
故障排除
Possible cause
Connection problem.
Temperature control is in MIN position.
Not enough water in tank.
Steam control is selected in non-steam position.
Not enough water in tank.
Steam jet function was used very frequently
within a short period.
Iron is not hot enough.
The iron is not hot enough.
You have used hard water, which has caused scale
flakes to develop in the water tank.
The iron has been put in horizontal position while
there is still water in the water tank.
可能的原因
连接故障。
温度控制位于"MIN"（最低）位置。
水槽中的水不够。
蒸汽控制的选择位于无蒸汽的位置。
水槽中的水不够。
短时间内使用蒸汽喷射功能的次数过多。
熨斗热度不够。
熨斗温度不够高。
您使用了水质较硬的水，这会使水槽中
形成水垢渣。
熨斗已置于水平位置，但水槽中仍有水。
Solution
Check main power supply cable, plug and
outlet.
Select adequate temperature.
Fill water tank (see "Getting started", no 2).
Set steam control between positions of
minimum steam and maximum steam (see
"Ironing chart").
Fill water tank (see "Getting started", no 2).
Put iron on horizontal position and wait before
using steam jet function.
Adjust the proper temperature to steam
••
ironing (up to
). Put iron in vertical position
and wait until temperature indicator light
turns off.
Set the temperature dial to a temperature
••
(
to maximum) suitable for steam ironing.
Put the iron on its heel and wait until the light
has gone out before you start ironing.
Use the self-clean function one or more times.
Empty the water tank and set the steam
control to position off before storing the iron.
解决办法
检查电源电缆、插头和插座。
选择适当的温度。
向水槽注水（请参见"入门指南"，第 2 步）。
将蒸汽控制设置在最小和最大蒸汽之间（请参
见"熨烫表"）。
向水槽注水（请参见"入门指南"，第 2 步）。
将熨斗水平放置并稍候片刻，然后再使用蒸汽
喷射功能。
将温度调整到适合进行蒸汽熨烫的温度（上调
••
至
。将熨斗垂直放置并稍候片刻，直到温度
指示灯熄灭。
"将温度旋钮旋至适合进行蒸汽熨烫的温度
••
（
到最高）。将熨斗立起，等待指示灯熄
灭，然后再开始熨烫。"
使用一次或多次自清洁功能。
将水槽中的水倒空，并将蒸汽控制旋钮
置于"关闭"位置，然后再将熨斗收起。
Advertisement
