Troubleshooting
The following offers solutions to some of the common problems you may encounter. We suggest that you consult
this chart before contacting your dealer.
PROBLEMS
The power is off.
• The air inlet grille, outlet grille or air filter is
clogged with dust or some other obstruction.
POWER indicator does not light up.
• Power cord is unplugged from the outlet.
• Power cord is disconnected from the projector.
• The main switch is turned off.
• The lamp lid is open.
Power indicator blinks red.
• The projector has been turned on again too soon
after having been turned off.
• When the power switch was turned off while
the fan was running, during or after lamp
operation.
• The room temperature is too high.
(Does the STATUS indicator show an unusual
condition?)
• Lamp is no longer working.
POWER indicator blinks between red and green.
• The lamp cover is not closed.
• When the STATUS indicator is on or blinking,
the main unit requires repairs.
No picture appears
• Lens is covered by lens cap.
on the screen.
• When the STATUS indicator is on or blinking,
the main unit requires repairs.
• The equipment connected to this projector is not
turned on.
• Other equipment is not connected properly.
• The input source is not selected correctly.
• A long RGB cable is being used instead of the at-
tached RGB cable.
• The air inlet grille, outlet grille or air filter is
The image is
clogged with dust or obstructed.
turned off.
(In this case, the STATUS indicator does not light up.)
• The projector is not at a right angle to the screen.
The image is
distorted.
The image is dark.
• Brightness, tint and color are not adjusted correctly.
• The projecting distance is beyond the focused area.
• Lens is dirty.
The image is
• Screen size exceeds screen size specifications.
blurred.
• Brightness and contrast are not adjusted correctly.
• FINE adjustment is not made correctly.
• Tracking is not adjusted.
• The projector is not at a right angle to the screen.
The image is dis-
• The cable for connection with other equipment
torted on the screen
and noise is heard.
• The projector is installed too close to other
No sound is heard.
• Volume is not turned up.
• Connection to other equipment is not made correctly.
Nothing is displayed on
• The PC monitor is not turned on.
the PC monitor.
Warm air comes out of
• This is typical of the projector.
the exhaust vents.
A rainbow blur appears
• Such blur appears based on the principle of the DLP system. It isn't a failure.
on the image.
• The operation is incorrectly made due to noise or
Adjustments cannot be
interference.
made.
is displayed.
• This mark is displayed when an invalid operation is executed. This is not failure.
CAUSE
is not plugged securely into the terminal.
equipment.
POSSIBLE SOLUTIONS
• Remove the obstruction.
• Plug the power cord into the outlet.
• Insert the power cord into the projector.
• Turn the main switch on.
• Close the lamp lid.
• Wait for the lighting sequence.
• Turn the power switch on and off several times.
• Refer to "Indicators" on page 26.
• Replace the lamp with a new one.
• Close the cover correctly.
• Contact your dealer.
• Take the lens cap off.
• Replace the lamp with a new one.
• Turn on the connected equipment.
• Confirm the connections.
• Select the correct source according to the equip-
ment connected to this projector.
• Check whether a picture appears or not using the at-
tached RGB cable. If a picture appears, use an RGB
signal amplifier in addition to the long RGB cable.
• Remove the obstruction and turn off the main
power switch. After about 10 minutes, turn the
projector on.
• Adjust the angle of the projector to make a right
angle to the screen. See page 12.
• Adjust brightness, tint and color correctly.
• Adjust the projecting distance. See page 9.
• Clean lens.
Use a screen size to within 40" to 300".
•
• Adjust brightness, contrast.
• Make FINE adjustment.
• Adjust tracking.
• Adjust the angle of the projector to make a
right angle to the screen. See page 12.
• Plug the connecting cable securely into the
terminal. See pages 10-11.
• Increasethe distance between the projector
and other equipment.
• Turn up the volume.
• Check connections. See pages 10-11.
• Turn on the monitor.
Turn off the main power, wait about 10 min-
•
utes, and turn on the main power again
.
EN – 27