JLAB Fit Sport 2.0 - Wireless Fitness Earbuds Manual

Table of Contents

Contents

1 FIRST TIME SETUP: BLUETOOTH PAIRING
2 ACCESSORIES
3 BUTTON FUNCTIONS
4 EQUALIZER MODES
5 CHARGING
6 FITTING
7 CABLE CLIP USE
8 CONNECTION TROUBLESHOOTING
9 WARM-UP YOUR HEADPHONES
10 Documents / Resources
- 10.1 References
- 10.2 Download manual

FIRST TIME SETUP: BLUETOOTH PAIRING

Turn on the Bluetooth in your device settings.
Press and hold button for 10 seconds.
Release.
Light will blink red and blue to indicate pairing mode.
Select "JLab BT" in your device settings to connect.
Light will slow blink blue when Bluetooth is paired.

RECURRING USE
Once JLab Fit Sport has initially paired to your device, the earbuds will auto-connect to your Bluetooth device when powered back ON.
(Follow BUTTON FUNCTIONS instructions)

ACCESSORIES

BUTTON FUNCTIONS

BUTTON FUNCTIONS
VOLUME UP: Click once.
TRACK FORWARD: Click & hold 2+ seconds.
POWER ON: Click & hold 3 seconds.
POWER OFF: Click & hold 5 seconds.
PLAY / PAUSE ANSWER / HANG UP CALLS: Click once.
ACTIVATE SIRI (iOS) OR "OK GOOGLE" (ANDROID): Click twice.
BLUETOOTH PAIRING: (Follow First Time Setup: Bluetooth Pairing)
VOLUME DOWN: Click once.
TRACK BACKWARD: Click & hold 2+ seconds.

EQUALIZER MODES

EQUALIZER MODES
Quick press both buttons for different EQ settings
(Fit Sport will cycle 3 EQ settings)
JLab SIGNATURE (One Beep)
JLab C3™ signature sound with amplified vocals and bass
BALANCED (Two Beeps)
Even sound with no additional sound enhancements
BASS BOOST (Three Beeps)
Amplified bass and sub-bass

CHARGING

Open USB door and connect the cable to a computer or USB power source to charge. Make sure the charging source is rated at 5V or less.
Light will turn solid red when charging and turn blue when fully charged.

FITTING

Shape Memory Wire to your preference.
Start from the back and rotate around the ear.
Secure cable in front, back and bottom.

CABLE CLIP USE

Attach the cable clip near the center of the cable.
Clip in the back or front position of shirt.

CONNECTION TROUBLESHOOTING

I DO NOT SEE JLAB BT IN MY DEVICE

Turn Bluetooth off and then back on in device settings.
If you still do not see JLab BT, repeat FIRST TIME SETUP: BLUETOOTH PAIRING directions.

JLAB BT DOES NOT RECONNECT TO MY DEVICE AFTER POWERING ON

In device settings, forget the JLab BT.
Turn Bluetooth off then back on in device settings.
Repeat FIRST TIME SETUP: BLUETOOTH PAIRING directions.

BLUETOOTH IS CONNECTING TO AN UNWANTED DEVICE

Note: The JLab BT can remember up to 8 devices. It will try to auto-connect to last device used.

If you have more than one device that was connected to JLab BT, turn OFF Bluetooth on unwanted devices and turn ON Bluetooth on chosen device.
Press and hold button for 10 seconds.
Release.
Light will blink red and blue to indicate pairing mode.
Light will slow blink blue when Bluetooth is paired.

Make sure USB door is closed and fastened.
This will protect against sweat and water damage.

Before charging, the Fit Sport earbuds need to be fully dry.
If there is any exposure to moisture, the internal components may become damaged.
It is best practice to air dry before charging.

WARM-UP YOUR HEADPHONES

Optional: Burn-in is the process for exercising new audio equipment. We recommend 40 hours of burn-in time for most headphones to reach optimal performance. The main purpose of the process is to loosen the diaphragm of a newly crafted headphone and to stress the headphone driver. Normal, everyday use can also burn-in the headphones though JLab's proprietary burn-in provides an ideal mix of sounds and frequency sweeps to achieve this.

Burn-in your audio equipment with the JLab Audio app available on the App Store and Google Play.
Or access the burn-in method at: jlabaudio.com/burnin

Avoid getting moisture or liquids into the tip of the earbuds or charging port.
Avoid extreme heat, cold, and humidity.
Avoid dropping or crushing the earbuds, stressing the cable by rapid pulling or extreme force, or bending the cable at a sharp angle.
Wax may build up in the earbud tips, lowering the sound quality. Carefully remove the wax with a cotton swab or other small tool to improve the sound quality.
If you experience discomfort or pain, try lowering the volume or discontinuing use temporarily.
If you experience regular discomfort while using this product, discontinue use and consult your physician.
We recommend you treat your earbuds as you would a nice pair of sunglasses and keep them in safe location when not in use.

JLABAUDIO.COM

YOUR SATISFACTION IS GUARANTEED
You may exchange or return merchandise within 30 days of the purchase date.
Learn more at jlabaudio.com/guarantee

YOUR WARRANTY
You may register your product at jlabaudio.com/register. All warranty claims are subject to JLab Audio authorization and at our sole discretion. Retain your proof of purchase to ensure warranty coverage.

CONTACT US
Reach out to us at support@jlabaudio.com or visit jlabaudio.com/contact