Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for ALDI FERREX FS 850-2
Summary of Contents for ALDI FERREX FS 850-2
- Page 1 User manual RECIPROCATING SAW Original instructions ID: #05007...
-
Page 2: Package Contents
Package contents Reciprocating saw Saw blade... -
Page 3: Table Of Contents
Table of contents Table of contents Package contents .....................2 General information ..................4 Reading and storing the user manual ..............4 Proper use ........................4 Residual risks ......................5 Explanation of symbols .................. 5 Safety ....................... 6 Explanation of notes ....................6 General power tool safety instructions ..............6 Safety instructions for reciprocating saws ............9 Supplementary safety instructions .............. -
Page 4: General Information
General information General information Reading and storing the user manual This user manual is part of this reciprocating saw (referred to below only as the ‘product’). It contains important information on safety, usage and care. Before using the product, read the user manual carefully. Pay particular attention to the safety notes and warnings. -
Page 5: Residual Risks
Explanation of symbols Residual risks Despite proper use, inconspicuous residual risks cannot be completely ruled out. The following risks may arise due to the design of the product: • Touching the exposed areas of the saw blade; • Reaching into the rotating saw blade (cut injury); •... -
Page 6: Safety
Safety Safety Explanation of notes The following symbols and signal words are used in this user manual. Indicates a hazardous situation that, if not avoided, could result in death or serious injury. WARNING! Designates a dangerous situation that may result in minor or moderate injury if not avoided. - Page 7 Safety Electrical safety a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock. b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators.
- Page 8 Safety d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Take care to keep a normal body position. Maintain a stable stance and balance at all times.
-
Page 9: Safety Instructions For Reciprocating Saws
Safety f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g) Use the power tool, accessories and fitted tools etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. -
Page 10: Supplementary Safety Instructions
Safety − Only run the saw up to the work piece once it has been switched on. − Never process material containing asbestos. Use a protective mask and dust extractor for other fibrous material. − Do not slow down the saw blade by applying side pressure. −... - Page 11 Safety WARNING! Risk of injury! This product is not intended to be used by persons with impaired physical, sensory or mental abilities or who lack experience and/or knowledge, unless they are supervised by a person responsible for their safety or are instructed by such a person on the use of the device.
- Page 12 Safety CAUTION! Danger to health! You may damage your health if you use the product over a longer period of time due to the hand-arm vibration. − Wear vibration-reducing gloves. CAUTION! Risk of injury! Improper handling of the product can lead to injury. −...
-
Page 13: Product Description
Product description Product description The product is a mains-powered reciprocating saw for sawing materials such as wood, metal and plastic. The reciprocating saw has a saw blade holder with rotary toggle for holding commercially available reciprocating saw blades with a 1/2” universal shaft. A saw blade for wood is included. -
Page 14: First Use
First use Adjustment wheel Saw shoe (stroke rate limit) Saw blade holder Continuous operation switch Rotary toggle On/Off switch LED work light Handle Handle surface Mains cord Lock slide First use Checking the product and package contents 1. Lift the product out of the packaging with both hands. 2. -
Page 15: Inserting/Changing The Saw Blade
Inserting/changing the saw blade CAUTION! Risk of injury! The saw blades are very sharp. Also, the saw blades can become hot during sawing. Both of these issues can lead to injuries if you do not handle the product carefully. − Be extremely careful when inserting or changing the saw blade. −... - Page 16 You can set the desired or required cutting depth using the adjustable saw shoe. The maximum cutting depth for wood is 180 mm, for metal it is 8 mm (see Fig. B). Select the cutting depth so that the saw blade is in contact with the workpiece in every stroke position along the entire length that the saw is engaged.
-
Page 17: Adjusting The Saw Alignment
Adjusting the saw alignment The front part of the product can be turned 90° to the left or right. This allows you to saw in a sideways direction. 1. Make sure that the product is disconnected from the mains. 2. Pull the lock slide in the direction of the arrow and hold it in this position (see Fig. -
Page 18: Connecting
Connecting − To connect the product, insert the mains plug of the mains cord into a properly installed socket. Sawing WARNING! Risk of injury! Accidentally starting the product may result in severe injury caused by the saw blade. − Always use both hands to hold the product on the handles intended for this purpose in order to be able to use the product safely. - Page 19 Sawing in normal operation 1. Secure the workpiece with suitable clamping elements (e.g. vices). Ensure that the clamping elements are fixed securely to prevent them being loosened by the vibrations caused by the product. 2. If necessary, set the maximum number of strokes using the stroke rate limiter (see “Adjusting the stroke rate limit”).
- Page 20 Sawing in continuous operation NOTICE! Risk of damage! Improper use of continuous operation may damage the workpiece. − Before using continuous operation, set a stroke rate limit that is suitable for the material being worked to prevent the workpiece from being damaged by an excessive stroke rate.
-
Page 21: Led Work Light
Troubleshooting 8. To switch off the product after sawing, press the on/off switch to stop continuous operation. Then let go of the on/off switch. The product will gradually come to a stop. Do not put down the product while it is coming to a stop. -
Page 22: Cleaning And Maintenance
Cleaning and maintenance Cleaning and maintenance WARNING! Risk of injury! Accidentally starting the product may result in severe injury caused by the saw blade. − Always switch the product off and pull the mains plug out of the socket when you are not using the product, when cleaning it, servicing it, replacing parts or in the event of a fault. -
Page 23: Cleaning
Cleaning and maintenance NOTICE! Risk of damage! Improper handling of the product can damage the product. − Do not use water or chemical cleaning agents to clean the product. − Do not use any aggressive cleaners, brushes with metal or nylon bristles, or sharp or metallic cleaning utensils such as knives, hard scrapers, etc. -
Page 24: Transport
Technical data Transport − Remove the saw blade from the product. − Always use both hands to hold the product. − Secure the product to prevent it from slipping when transporting it in a vehicle. − If possible, use the original packaging for transport. Technical data Item number: 818298... - Page 25 Noise/vibration information • Sound pressure level L 89.83 dB(A) • Uncertainty K 5.0 dB(A) • Sound power level L 100.83 dB(A) • Uncertainty K 5.0 dB(A) The aforementioned values are noise emission values and therefore do not necessarily represent safe values for the workplace. The correlation between emission and emission levels cannot reliably provide for a conclusion as to whether additional cautionary measures are necessary or not.
-
Page 26: Disposal
Disposal − Wear vibration-proof gloves when using the product. − Maintain and service the product in accordance with this user manual. − Avoid using the product at temperatures below 10 °C. − Plan your work steps to avoid working with heavy vibration products over several days. -
Page 27: Declaration Of Conformity
Declaration of Conformity Declaration of Conformity Conmetall Meister GmbH Oberkamper Straße 39 42349 Wuppertal Germany EC Declaration of Conformity We declare with sole responsibility, RECIPROCATING SAW FS 850-2 that the product listed below … MARKE ® WU5908233/ WU5908234 • 818298 • 09/2022 …... - Page 28 PRODUCED IN CHINA FOR: ALDI STORES LTD. PO BOX 26, ATHERSTONE WARWICKSHIRE, CV9 2SH. ALDI STORES (IRELAND) LTD. PO BOX 726, NAAS, CO. KILDARE.
Need help?
Do you have a question about the FERREX FS 850-2 and is the answer not in the manual?
Questions and answers