Open And Close Commands - GIESSE VARIA SLIM RADIO Instruction And Installation Manual

• Connection of the manual control with 3 conductors [the common conductor on (
conductor for opening on (IN 1) and the conductor for closing on (IN 2)].

10. Open and close commands

10.1. Remote electronic control (Radio remote control)
The RC radio remote control is the standard-equipped device for controlling the VARIA SLIM RADIO motor.
For more details on the characteristics and operation of the RC radio remote control, consult the instructions manual provided
with the radio remote control itself.
Some functions of the radio remote control are not discussed in this manual.
T NOT
HE TRANSMITTER IS
First follow the radio remote control instructions and then those provided below concerning the specific operation of
the machine you would like to control.
10.1.1. Saving the radio remote control
The radio remote control supplied is the RC model, with 30 channels and a display, which transmits at the radio frequency of
433.92 MHz; no other radio remote control model is provided for the VARIA SLIM RADIO. Several actuators can be controlled
with a single radio remote control, however each channel must correspond to a VARIA SLIM RADIO actuator and thus a window.
The encoding used varies for each channel, so each transmission will send a signal that is different from all the others. It follows
that the receiver must be able to recognize the enabled transmitters, thus the transmission codes should be saved following the
procedure below:
▪ Equip yourself with the radio remote control, checking beforehand that it is working, has charged batteries and is in good
condition.
▪ Select the desired channel on the radio remote control. (Consult the instructions manual of the RC radio remote control).
▪ On the VARIA SLIM RADIO, briefly press (for about 1 second) the small "
slowly flashing LED indicates that it is waiting to receive a valid radio code.
▪ Within 10 seconds, press any one of the up arrow ▲,
display of the radio remote control and the second time to transmit the radio code).
▪ If the code is saved correctly, the LED will emit one long flash (1 sec.) to confirm; then the LED will go out and remain at
rest.
▪ If the code is not saved correctly - due to the memory being full, for example, or the radio remote control being
incompatible - the LED will emit a series of quick flashes for about 1 second; then the LED will go out and remain at rest.
10.1.2. Erasing the radio memory
To completely erase the memory of the radio remote control on the machine, press the "
about 20 seconds until the LED begins to flash quickly. At this point you can release the button; the flashing continues until the
memory has been completely erased.
10.1.3. Remotely saving a radio remote control
A new radio remote control can be saved remotely – i.e., without accessing the
control has already been saved as described in point 10.1.1 and you have the radio remote control which is already recognized.
To remotely save a radio remote control, follow the procedure below:
▪ Equip yourself with the RC radio remote control to be saved and set it on the desired channel (see the instructions provided
with the radio remote control).
▪ Equip yourself with the radio remote control already saved and operating on the VARIA SLIM RADIO in question.
▪ On the already saved radio remote control, press the following buttons in sequence: F1, F2 and then
"opens" the memory of the VARIA SLIM RADIO (in the same way as pressing the PRG button).
▪ Within 10 seconds, press any one of the up arrow ▲,
you want to program two times (once to activate the display of the radio remote control and the second time to transmit the
radio code).
10.2. Control with conventional button
If necessary, due to unavailability of the radio remote control or other reason, the controls can be connected by cable.
The control must have a clean (voltage-fee) single-pole contact, normally open, or a deadman's button, but not a stable switch. It
should be connected to the left terminal block in the actuator, as indicated in the previous "Electrical connection" chapter.
- .
FACTORY PROGRAMMED
" button located near the terminal block. The
PRG
or down arrow ▼ buttons two times (once to activate the
STOP
PRG
or down arrow ▼ buttons of the (new) radio remote control that
STOP
21
), the
COM
" button and hold it pressed for
PRG
button – only if at least one radio remote
STOP
. This sequence