Page 1
COLOR TELEVISION RECEIVER Chassis : S16A(P)_GREEN-2 SERVICE Manual COLOR TELEVISION RECEIVER FEATURES Green CRT ■ ■ ■Multi Wide System LNA Plus(Low Noise Amplifier) ■ ■ ■Turbo Plus DNIe jr. ■ ■ ■Low Stand-By Power Wattage ■SOUND Equalizer CW-29M064N...
Page 5
COLOR TELEVISION RECEIVER Chassis : S16A(P)_GREEN-2 Model : CW29M064N2XXEC SERVICE Manual COLOR TELEVISION RECEIVER FEATURES Green CRT ■ ■ ■Multi Wide System LNA Plus(Low Noise Amplifier) ■ ■ ■Turbo Plus DNIe jr. ■ ■ ■Low Stand-By Power Wattage ■SOUND Equalizer CW-29M064N...
Page 9
4. When replacing the Side AV Ass'y : No adjustments required 5. When replacing the PIP Module : No adjustments required 6. When replacing the Control Ass'y : No adjustments required 7. When replacing the PFC Ass'y : No adjustments required Samsung Electronics...
Page 10
4. W/B Setting Item Data Required Adjustment White x:272 3 y:270 3 Y:50 ± ± ± White Balance (Standard Data) Balance x:265 3 y:266 3 Y:2.0 ± ± ± Toshiba Pattern Screen Voltage Same as ET Basic Model G2 Adjust Samsung Electronics...
Page 12
16:9 H Trapezium Adj/Opt FIX/32 FIX/32 WIDE Only 14:9 V Amp Adj/Opt FIX/32 FIX/32 WIDE Only 14:9 V Shift Adj/Opt FIX/32 FIX/32 WIDE Only 14:9 H Parabola Adj/Opt FIX/32 FIX/32 WIDE Only 14:9 H Trapezium Adj/Opt FIX/32 FIX/32 WIDE Only Samsung Electronics...
Page 14
PIP Only PIP R Cutoff Opt/Fix PIP Only PIP G Cutoff Opt/Fix PIP Only PIP B Cutoff Opt/Fix PIP Only PIP R Drive Opt/Fix PIP Only PIP G Drive Opt/Fix PIP Only PIP B Drive Opt/Fix PIP Only Samsung Electronics...
Page 15
Comb Filter De Interlace Chroma Trap Mode Black Current Measure Line EHT Tracking Mode 5. YC Delay Item Adjust Standard SET Southeast Asia Remark PAL Delay SECAM Delay NTSC Delay PAL AV Delay SECAM AV Delay NTSC AV Delay Samsung Electronics...
Page 16
Ratio Pre & After Shoot Ratio posi & Nega Peaks Dynamic Skin Control Gamma & White Stretch Video Dependent Coring PAL/NTSC Ident Sensitivity Comb Filter Diode Clamp DC Transfer Ratio 272/270 272/270 50FL 35FL WHITE BALANCE 265/266 265/266 2.0FL 2.5FL Samsung Electronics...
Page 17
② Press "Power Off →Info → Menu → Mute → Power On" using the remote control and enter Factory Mode. ③ Enter Deflection Mode. ④ Adjust the V-AMP, V-SHIFT, H-AMP and H-SHIFT items so that the width becomes 5 and the height becomes 4. Samsung Electronics...
Page 18
⑦ When the adjustments are complete, display the Lion pattern and check that the picture size has not been changed. If there is no change, finish the adjustments. 3-10 Samsung Electronics...
Page 19
1. To enter Service Mode, press the keys on the remote control according to the following sequence. (in Stand-by status) Info → Menu → Mute → Power On 2. When entering Service mode, the software information is displayed at the top of the service mode menu OSD. ex) T-GRN2PEU-1000 2005/0X/XX Samsung Electronics 3-11...
Page 20
- Check the “Flash selection” item is appoint “Manual” - You can adjust program delay time for program speed but we use the normal “5[ms]” - Check the green lamp if this is sometime red lamp you can not programming 3-12 Samsung Electronics...
Page 21
- Click the “Erase Flash” button for before program erase - You can select flash selection item but we use normal “All” mode - Change the “Select flash ROM to erase. When ready press Send.” - Click the “Send” button Samsung Electronics 3-13...
Page 22
- Click the “Browse” button and find the new program folder in your computer - Click the “Send” button 6. Verify new program - Click the “Verify Flash” button - Change the “Select flash to verify correct programming. When ready press Send.” - Click the “Send” button 3-14 Samsung Electronics...
Page 23
4. Slowly turn the Static Focus VR counter clockwise so that the center vertical line is the most clearly displayed. [adjusted point : Center(2/1)] 5. Check the entire screen focus and repeat steps 3 to 4, if necessary. Samsung Electronics 3-15...
Page 24
2. Initialize all settings to the values appropriate to the corresponding model. 3. Display the Toshiba pattern. 4. First check IBRM in "G2 Adjust" of Factory and adjust Screen VR until the color of IBRM item turns green. 3-16 Samsung Electronics...
Page 25
4. When the adjustment is finished, check the following checklist. - If there is a spot on the screen when turning the TV set off/on, adjust the Screen Voltage again. - If there is a ghost line on the screen, adjust the Screen Voltage again. Samsung Electronics 3-17...
Page 35
The mirror returns to a blank state so that no stains or after-images are left. The SAMSUNG SKY500N model has both an ANYNET port and a SERVICE jack port. Because the shape of the ANYNET port on the DLP TV is the same as that of the SERVICE jack port of the SKY500N, it fails to turn the TV off after a connection has been reported.
Page 36
Ex: For LCD 15:9 devices, "Wide" is displayed on the OSD instead of "16:9". 4. The picture size can be changed even in the blue screen. However, the picture size should be controlled by the product specifications if the change is impossible due to hardware restrictions. 14-2 Samsung Electronics...
Page 37
You can use this AV interface for users by controlling connected AV devices function to study English by watching AFKN or CC marked through the Anynet menu when AV devices of Samsung video tapes. Electronics are connected.
Page 39
Operation Instruction & Installation 11. Operation Instruction & Installation 11-1 Product Features and Functions 11-1-1 Front 11-1-2 Side 11-1-3 Rear Samsung Electronics 11-1...
Page 40
P.MODE displayed. Used to select the VIDEO picture effect. Used to display all of the S.MODE available video sources. Used to select the sound effect. 11-2 Samsung Electronics...
Page 41
③ Tap the upper part of the Back Cover 2 or 3 times and pull the Back Cover to separate it from the unit. Notice: Disassemble the product after disconnecting the power cord and discharge the unit to prevent an electric shock and damage to the product due to static electricity. Samsung Electronics 12-1...
Page 42
Press the clip down completely and pull the con- nector. ① Separate theAV and Main Board from the Front Cabinet and AV Wire, GT-Pin Wire. ② To separate the Wire, Fixing clip and pressing the Wire. 12-2 Samsung Electronics...
Page 43
① Separate the cables connecting the FBT and the CRT. Notice: Since there may be a remaining high-voltage current within the CRT, take care not to touch the CRT hole with metal or a part of yourself when separating the cables. Samsung Electronics 12-3...
Page 44
Notice : Take care when separating the wires because pulling the wires by force may damage the socket. In addition, separate the wires on a flat and clean surface so as to prevent scratching of the material and the PCB. 12-4 Samsung Electronics...
Product Specification 2-4 Accessories Accessories Item Item code Remark Remote Control / AA59-00312J/ Alkaline Battery 4301-000121 (1.5V AAA)2EA Samsung Service center User Manual AA68-03621A Warranty Card AA68-03242B Coaxial cable HDMI/DVI cable HDMI Cable Video Cable / Internal shopping mall Audio Cable...
Page 49
* CNV501 : A 8pin port connected to the CRT ASS'y which outputs the R/G/B signal to the CRT ASS'Y for display. In addition, this port outputs the necessary TILT, VM, and Power signals to the CRT DRIVE. * CNP12 : An 3 pin port connected to the PIP Module, which receives PIP-CVBS input. Samsung Electronics...
Page 50
PIN No. Pin Name V-OUT B-OUT G-OUT V-IN R-OUT L-OUT SENSE R-OUT L-IN R-IN CNP12 CNV702 Connected to the PIP Module Connected to the AV Ass'y PIN No. Pin Name PIN No. Pin Name C-IN PIP-CVBS Y-IN C-OUT Y-OUT Samsung Electronics...
Page 51
* CNP02 : A 8pin port inserted into the MAIN ASS'y, which connects various signal control ports necessary for PIP signal processing and product operation. * CNP03 : A 8pin port inserted into the MAIN ASS'y, signals to the PIP-CVBS. Samsung Electronics...
Page 52
Connected to the Main Ass'y PIN No. Pin NAME PIN No. Pin NAME OSD-R B+8V OSD-G B+5V OSD-B OSD-F/B SUb-CVBS PIP-CVBS H-SYNC C-IN V-SYNC PIP-F/B PIP-B PIP-G PIP-R CNP03 Connected to the Main Ass'y PIN No. Pin NAME PIP-CVBS Samsung Electronics...
Page 53
* CN503 : The R/G/B output signal from the VCTi Module & the power, which is required to drive the CRT and the AMP, from the DEFLECTION BLOCK is connected to this port. 9-3-3 CRT Board Connector Pin CN503 Connects the R/G/B signal from the VCTi Module. PIN No. Pin NAME B-OUT G-OUT R-OUT SENSE HEATER B+200V Samsung Electronics...
Page 55
When Check the AC power cord for possible damages. Keep voltage exceeds the specified limits, check each special the part or the lead away from any heat-emitting part. materials. Samsung Electronics...
Page 56
Critical safety parts should be bracketed with ( Use only regular parts for replacements (in particular, flame resistance and dielectric strength specifications). Irregular parts or materials may cause electric shock or fire. Samsung Electronics...
Page 57
5. Check for insulation between the blade of the AC plug 10. The sharp edges of the metal material may cause and that of any conductive materials (i.e. the metal physical damage, so ensure wearing protective gloves panel, input terminal, earphone jack, etc). during the repair. Samsung Electronics...
Page 58
These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Samsung Electronics...
Page 59
5. Make sure to turn the power off and unplug the power cord from the outlet before repositioning the product. Also check the antenna cable or the external connectors if they are fully unplugged. Damage to the cord may cause fire or electric shock. Samsung Electronics...
Page 67
Block Diagram 7-2-5 Supply Scheme with Voltage Guards and Power On Reset Unit Samsung Electronics...
Page 68
Block Diagram 7-2-6 CVBS Switch 7-2-7 The UOCIII TV Sound Concept Samsung Electronics...
Page 69
Block Diagram 7-2-8 Overview of the UOCIII sound functions on the digital controller 7-2-9 Demodulator and Decoder Block Diagram Samsung Electronics...
Page 80
Schematic Diagram 10. Schematic Diagram 10-1 POWER & DEFLECTION BLOCK This Document can not be used without Samsung’s authorization. Power Signal Samsung Electronics 10-1...
Page 81
Schematic Diagram 10-2 IF & UOC(CHROMA_MICOM)BLOCK This Document can not be used without Samsung’s authorization. Power Signal 10-2 Samsung Electronics...
Page 82
Schematic Diagram 10-3 PIP & CRT BLOCK This Document can not be used without Samsung’s authorization. Power Signal Samsung Electronics 10-3...
Page 83
Schematic Diagram 10-4 AV & SOUND BLOCK This Document can not be used without Samsung’s authorization. Power Signal 10-4 Samsung Electronics...
Page 84
Wiring Diagram 8. Wiring Diagram 8-1 Overall Wiring Power Switch CONT ROL SIGNAL POWER POWER ON/OFF Contr ol Signal MAIN Audio Out AV Signal SPEAKER Main Input PIP Module CRT Power Supply M ai n Input Samsung Electronics...
Page 85
PIP- R CNV701 CNV702A V- OUT C- IN V- IN Y- IN L- OUT C- OUT R- OUT L- IN Y- OUT R- IN TU01S CN502 - 16.5V + 16.5V HEAT ER 2 SC AR T B+ 200V Samsung Electronics...
Page 98
2)Check that the Master Switch has been pressed. 3) Check that the transmitter is turned on. 4) Check that transmitter device selection is set to TV. 5) Check that the signal cable is properly connected. 6) Check that channel setting has been set. Samsung Electronics...
Page 99
” S D “ ” S r i a c i p & i l + D “ ( ” 1 t r a D “ ” 1 Q “ ” 1 Q “ ” 1 r i a Samsung Electronics...
Page 100
Cannot select an A/V channel. out, you cannot select an A/V channel. Check if the connector is properly connected. Cannot select a menu. Check if the menu is grayed out. If a menu is grayed out, it cannot be selected. Samsung Electronics...
Page 101
■ Set the auto volume control to ON. There is a lot of noise. Keep the antenna away from the power cord or connectors if possible. The selected language does not Press the Multiplex button to select the TV. appear. Samsung Electronics...
Page 102
This noise may occur when the plastic material inside the TV expands or contracts according The TV makes a noise as if to the seasonal temperature or humidity. This is like the noise from a furniture/cabinet/sink something is dropping inside. unit, and there is no need for concern. Samsung Electronics...
Page 103
You can check the checksum according in the following order. Factory Mode → Checksum → Right Button → Calculate Checksum → Output Checksum (e.g. 3036) ■ Checksum Examples T-TR2PEU-1000 : checksum = 8036 T-TR2PEU-1010 : checksum = B612 Samsung Electronics...