Page 1
ORDER NO.VR0603007CE DVD Recorder DMR-EH75VP Vol. 1 Colour (S).......Silver Type SPECIFICATIONS...
Page 2
2006 Matsushita Electric Industrial Co., Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law. 1. Safety Precaution 1.1. General guidelines 1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit.
Page 3
1.1.2. Leakage current hot check / (See Figure 1 1. Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check. 2. Connect a 1.5k , 10 watts resistor, in parallel with a 0.15 capacitors, between each exposed metallic part on the set and a good earth ground such as a water pipe, as shown in Figure...
Page 4
semiconductor-equipped assembly, drain off any ESD on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap, which should be removed for potential shock reasons prior to applying power to the unit under test. 2.
Page 5
2.2. Precaution of Laser Diode 2.3. Service caution based on legal restrictions 2.3.1. General description about Lead Free Solder (PbF) The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this equipment in considering the globally environmental conservation.
Page 6
- The lead free solder has to be used when repairing the equipment for which the lead free solder is used. (Definition: The letter of “PbF” is printed on the PCB using the lead free solder.) - To put lead free solder, it should be well molten and mixed with the original lead free solder.
Page 7
NOTE: The lithium battery is a critical component. ( Type No.: CR2354-1GUF Manufactured by Panasonic. ) It must never be subjected to excessive heat or discharge. It must therefore only be fitted in equipment designed specifically for its use. Replacement batteries must be of the same type and manufacture.
Page 8
5. Features 5.1. About DivX 5.1.1. General DivX is a new video compressing format that is applied MPEG4 technology to improve image quality and the compressibility, and it is developed by the DivXNetworks, Inc., Video file of high resolution and the high picture quality can be made though it is a high compressibility. DivX codec is necessary for converting video to DivX file and .playback files made.
Page 9
5.1.2. Operating Instructions about DivX Video-on-Demand Content DivX Video-on-Demand (VOD) content is encrypted for copyright protection. In order to play DivX VOD content on this unit, you first need to register the unit. Follow the on line instructions for purchasing DivX VOD content to enter unit's registration code and register unit.
Page 13
5.1.3. About DivX DRM Divx file includes file to which DRM(Digital Right Management) is applied and file not applied. This item is a content that relates only in treating file to which DRM is applied. 1. Registration Code display function 2.
Page 14
Moreover, Registration code is updated by new user authentication ever if same recorder. 2) User's registration and approval function - Only one user can register for one recorder. If user's registration is not done with the recorder, DivX file cannot be played back. - User's registration is performed only when a DivX DRM file is first chosen by recorder - DivX DRM file that can perform user's registration is only a file that...
Page 15
When it has reached head of title, the playback is ended, and screen becomes DivX menu (There is no resume) and then cursor is located on title that has been played back. Then if the same file was continuously played back, it begins to playback from the file head.
Page 16
Pin Name Pin layout of plug of HDMI cable seen from outside.
Page 17
5.2.2. Link functions with Equipments Corresponding Table Functions (1) Automatic Input switch (2) Link of Power In case setting of [FUNCTIONS] [Setup] [TV Screen] [Functions of HDMI] [Control with HDMI] are on, all above equipments Link functions are effective. 5.2.3. Outline of Equipments Linked functions (1) Automatic Input switch At starting of playback/ GUI display by DIGA, it turns on power of VIErA, and it displays picture of DIGA onto screen of VIErA.
Page 18
3. Automatic switch off of GUI display of DIGA when VIErA input selection/ VIErA operation menu is displayed GUI of DIGA is turned off when VIErA input selection is performed while GUI of DIGA is being displayed.And GUI of DIGA is turned off and VIErA operation menu is displayed when VIErA operation menu is displayed while GUI of DIGA is being displayed.
Page 19
(4) Power Link Power of DIGA is turned off linking to POWER OFF of VIErA. - Power of DIGA is not turned on linking to POWER ON of VIErA. - It is limited in following cases that DIGA links to POWER OFF of VIErA.
Page 20
Recording reservation. - Linking reservation from VIErA is not done. - Recordable media is fixed to HDD - Recording mode of digital program is fixed to DR and recording mode of analog program is fixed to SP mode. (6) Recording right now When [REC RIGHT NOW] is selected on GUI of VIErA, CH that is being seen is recorded by DIGA.And when [STOP RIGHT NOW] is selected on GUI of VIErA, recording of DIGA is stopped.
Page 21
6. Location of Controls and Components 6.1. Each Buttons 7. Operation Instructions 7.1. (DVD) Taking out the Disc from RAM-Drive Unit when the Disc cannot be ejected by OPEN/CLOSE button 7.1.1. (DVD) Forcible Disc Eject 7.1.1.1. (DVD) When the power can be turned off. 1.
Page 22
4. Push out Tray by Eject Pin (JZS0484) or minus screw driver (small). 7.2. (VHS) Removing Cassette Tape manually When the cassette tape could not be uninstalled from an electrical malfunction, there are 2 ways to remove a cassette tape. 7.2.1.
Page 23
2. Connect three batteries (1.5V spec.) to the Loading Motor in series for supplying 4.5V to rotate the Loading Motor as shown below. 3. Stop unloading just before unloading will be completed as shown below, and then the tape becomes slack as shown below. 4.
Page 24
5. Then unload again to remove the cassette tape as shown below. 7.2.3. (VHS) Take out Cassette Tapemanually after removing the mechanism 1. Disconnect the AC plug, and remove the Top Case, Front Panel and the Mechanism by referring to "10 Assembling and Disassembling"...
Page 25
4. Rotate the Capstan Motor clockwise to remove the slack tape as shown below. 5. Rotate the Main Cam Gear counter-clockwise again to remove the cassette-tape as shown below. 6. Attach Loading Motor and tighten the screw. 7. Set the Position Switch to EJECT POSITION certainly and attach the mechanism to chassis as shown below.
Page 26
8. Service Mode 8.1. (DVD) Self-Diagnosis and Special Mode Setting 8.1.1. (DVD) Self-Diagnosis Functions Self-Diagnosis Function provides information for errors to service personnel by “Self-Diagnosis Display” when any error has occurred. U**, H** and F** are stored in memory and held. You can check latest error code by transmitting [0] [1] of Remote Controller in Service Mode.
Page 27
Error Diagnosis contents Description Monitor Automatic FL Code Display Inoperative fan motor When inoperative fan motor is No display No display detected after powered on, the power is turned off automatically. The event is saved in memory. No error information Initial setting for error code in No display No display...
Page 28
Error Diagnosis contents Description Monitor Automatic FL Code Display HARD Drive error The drive detected a hard error. “DVD drive Display for 5 seconds. error.” IR ERR IR communication [IR ERR] is displayed when No display error communication between Timer microprocessor and IR microprocessor fails.
Page 29
Error Diagnosis contents Description Monitor Automatic FL Code Display [HDD ERR] is a) When normal start up was No display ERROR displayed when start failed. up of HDD was failed. b) When start up at HDD boot (Except error of was failed.
Page 30
Item FL display Key operation Mode name Description Front Key Forced disc eject Removing a disc that cannot be The display before When the power ejected. execution leaves. press [STOP] and keys simultaneously The tray will open and unit will seconds.
Page 31
Item FL display Key operation Mode name Description Front Key Aging Perform sequence of modes as * Display following the then When the power Aging Description shown below mode. press [CH DOWN], continually. to DVD DUBBING] [OPEN/CLOSE] simultaneously seconds and less seconds.
Page 32
Item FL display Key operation Mode name Description Front Key Demonstration Ejection of the disc is prohibited. *When lock the tray. When the power lock/unlock press [STOP] and The lock setting is effective until [POWER] keys unlocking the tray and not simultaneously released by “Main unit seconds.
Page 33
Item FL display Key operation Mode name Description (Remote controller Release Items Item of Service Mode executing Press [0] [0] or [ is cancelled. service mode. Error Code Last Error Code of U/H/F held by Press [0] [1] in service Display Timer is displayed on FL.
Page 34
Item FL display Key operation Mode name Description (Remote controller Magenta Picture Magenta picture is output with *Initial mode is “Interlace”. Press [1] [2] in service Output Component Output from AV mode. Decoder. *Magenta picture (Saturation rate: 100%) Switch Interlace/ Press [1] [4] in Magenta *It is enable to switch Interlace/ Progressive...
Page 35
Item FL display Key operation Mode name Description (Remote controller Audio Pattern The audio pattern stored in the Initial mode (Audio 48kHz) Press [2] [3] in service Output internal memory is output mode. (Lch: 1kHz/-18dB) (Rch: 400Hz/-18dB) Audio 44.1kHz/48kHz Press [2] [4] in Audio *Audio sound clock switching switching Pattern Output mode.
Page 36
Item FL display Key operation Mode name Description (Remote controller RAM Drive Last RAM Drive error code display. 1. Error Number is Press [4] [2] in service Error displayed for 5 seconds. mode. *For details about the drive error code, refer to the Service Manual When “INFO**** for the specific RAM Drive.
Page 37
Item FL display Key operation Mode name Description (Remote controller Delete the Last Delete the Last Drive Error Press [9] [6] in service Drive Error information stored on the DVD mode. RAM-Drive. Laser power Drive state is judged based on confirmation difference between laser power into RAM Drive in service...
Page 38
DD: Day Item FL display Key operation Mode name Description (Remote controller Display the Display the accumulated unit's Press [6] [4] in service accumlated working time. mode. working time (Indicating unit: Second) Display the Error Display the Error History stored Display reason of error for Press [6] [5] in service History...
Page 39
Item FL display Key operation Mode name Description (Remote controller SD card WRITE Delete Error History information When the WRITE check is Insert a SD card check stored on the unit. card slot, and press in service mode. *Insert SD card power is off.
Page 40
1. The indication "U" is displayed on the FIP while power remains on. 2. The indication "H" or "F" is displayed on the FIP, and the power is automatically turned off. When the power is turned on again, the Error indication code will disappear and the unit will return to normal display mode (either clock or counter is displayed).
Page 41
Memory No. Reason Automatic display Memory (Error No.) The cylinder could not be started. (Error of the cylinder or the cylinder driver.) The CAP FG could not be detected. Mechanism lock during without the unloading and the cassette-up. Mechanism lock during unloading S-reel pulse cannot be detected when a cassette tape is inserted.
Page 42
Item FL display Key operation Mode name Description Front Key Tracking Center Tape Tracking is adjusted No display. During PLAYBACK, to center FIX position. [CH UP] and [CH DOWN] keys simultaneously. VHS Service Mode In order to make service Press [STOP], and [ easy, a part of inside keys simultaneously information of a...
Page 43
Contents Contents of Indication on Contents of Indication on Remarks Service minute second Number Indication for Starting / finishing edges Data of receiving key (Real the inner data detecting data time) of IC6001 (Real time) 00: Both starting / Indicate the receiving finishing edges have not code when the key of VCR been...
Page 44
Contents Contents of Indication on Contents of Indication on Remarks Service minute second Number Self-diagnosis Error number of history 1 Supplementary data 1 and In the Self-Diagnosis history (1st) 2 of history 1. Memory, next 3 BYTE memorized for an Error. Self-diagnosis Error number of history 2 Supplementary data 1 and...
Page 45
2. There are the histories from number 1 to number 3. 3. The latest Error is memorized on history number 1,and then the old histories are shifted to the history number 2, 3. 4. Put out data from the memory number 3 by the shift is deleted. 5.
Page 46
*Display of means that " Loading Motor turns ON when [EJECT] button was pressed, but an error has occurred while mechanism was between REV position and LOAD position. <Supplementary Data 3> [EJECT] [FF] [REW] 10: PLAY passing REV U0: PLAY STOP F A0: PLAY STOP F...
Page 47
8.2.5.1. (VHS) Error Number and Supplementary Data The Supplementary Data as shown below are memorized to each error number. Error Reason Supplementary Data Data 1 Data 2 Data 3 Data The cylinder could not be started. VHS mode - (Error of the cylinder or the cylinder driver.) The CAP FG could not be detected.
Page 48
Error Reason Supplementary Data Data 1 Data 2 Data 3 Data NG2 in the PG Shifter Automatic VHS mode - Process Adjustment (The vertical sync signal is lacked while over 5 seconds on the alignment tape.) NG3 in the PG Shifter Automatic VHS mode - Process Adjustment...
Page 49
Note 3: Supplementary Data 2 (Reason of Ejection) Supplementary Data 2 Reason S-reel pulse is less than 3 when the loading has been completed. (Miss catching the tape) Pulse Timer over during the short rewind at the DOWN position. (Error of S-photo sensor system, S-reel system, Capstan system) Mechanism lock from the DOWN position to the LOAD position during loading.
Page 50
Part Number Description Compatibility RFKZ0260 Extension Cable (Main P.C.B. - RAM / Digital P.C.B. Same as ES10 Series Module / 88 Pin) JZS0484 Eject Pin Same as ES15 / E50 Series RFKZ03D01K Lead Free Solder (0.3mm/100g Reel) Same as ES15 Series RFKZ06D01K Lead Free Solder (0.6mm/100g Reel) Same as ES15 Series...
Page 51
10.2. P.C.B. Positions 10.3. Caution with inserting cassette tape when disassembling the unit Note1: For description of the disassembling procedure, see the section 10.4. Note2: Video Cassette might not enter when a strong lighting is applied to VHS Mechanism when Video Cassette is inserted.
Page 52
10.4. Top Case 1. Remove the 4 screws (A) and 3 screws (B). 2. Slide Top Case rearward and open the both ends at rear side of the Top Case a little and lift the Top Case in the direction of the arrows.
Page 53
10.5. Front Panel 1. Remove one screw (A). 2. Unlock tab (A) and tab (B) simultaneously. 3. Unlock tab (C) and tab (D) simultaneously. 4. Unlock 2 tabs (E) respectively, and pull out Front Panel with connector slightly. Note: When attaching Front Panel, in order to hook Cassette Door Opener Lever to Cassette Door, push up cassette door in the direction of arrow and insert a front panel.
Page 54
10.6. Front (L) P.C.B. & Front (R) P.C.B. 1. Remove 5 screws (A) to remove Front (R) P.C.B. 2. Remove 3 screws (B) and unlock Locking Tab (A) to remove Front (L) P.C.B. 10.7. RAM / Digital P.C.B. Module 1. Remove 3 Screws (A).
Page 55
2. With holding DVD drive as below illustration, remove 3 Screws (B) and disconnect 3 FFCs. And lift up Digital P.C.B. slightly so to disconnect connectors to remove Digital P.C.B.. 3. Put Digital P.C.B. on RAM Drive and remove RAM/Digital P.C.B. Module.
Page 56
Note: RAM/Digital P.C.B. Module as service part has no heat sink unit. Before returning to customer, heat sink unit should be installed on Digital P.C.B.. 10.8. HDD...
Page 57
Handling of HDD The following precautions should be taken when handling HDD. 1. Never give an impact to HDD. (Even a drop from 1cm height can be a cause of HDD failure. 2. When placing HDD on a workbench, provide a mat on a bench for shock absorption and anti-static purposes.
Page 58
2. Disconnect the wire with connector from Digital I/F P.C.B.. 3. Remove the 4 Screws (B) and FFC to remove HDD Bracket with HDD. 4. Put HDD with HDD angle up and down inversely so as not to give a shock to HDD. 5.
Page 59
10.9. VTR Mechanism Unit 1. Disconnect 3 Connectors (P1531, P2501 and P4002). 2. Remove 3 Screws (A), Screw (B) , Screw (C) and Screw (D). 3. Lift up VTR Mechanism Unit perpendicularly so to disconnect Connectors (P2571 and P3001).
Page 60
Note: Pay attention to stiff connections of P2571 and P3001, when removing VTR Mechanism Unit. 10.9.1. Caution for attaching VTR Mechanism Unit 1. Because Position SW should be set to "Eject Position", refer to fig.(A) and set the position switch so that the boss and arrow mark come on a straight line.
Page 61
1. Remove 7 Screws (A). 2. Remove SD Card/DV Jack P.C.B. with Digital Angle. 10.11. Rear Panel & Fan Motor 10.11.1. Rear Panel with Fan Motor 1. Disconnect Fan Connector. 2. Remove 8 Screws (A) and 2 Screws (B). 3. Unlock 2 Locking Tabs (A) to remove Rear Panel with Fan Motor. 10.11.1.1.
Page 62
10.12. HDMI P.C.B. 1. Disconnect FFC. 2. Pull up HDMI P.C.B. for the direction of arrow. 10.13. Power & Digital I/F P.C.B. 1. Disconnect 5 Connectors (A).
Page 63
2. Remove the 2 Screws (A). 3. Remove Power & Digital I/F P.C.B. 10.14. Main P.C.B. 1. Disconnect 5 Connectors. 2. Remove 2 Screws (A) and remove Main P.C.B.
Page 64
11. Measurements and Adjustments 11.1. Service Positions Note: For description of the disassembling procedure, see the section 10. 11.1.1. Checking and Repairing of Power & Digital I/F P.C.B.
Page 65
11.1.2. Checking and Repairing of Main P.C.B.
Page 66
11.1.2.1. Checking IR Circuit NOTE1: Even if Main P.C.B. is not removed, IR Circuit can be checked. NOTE2: Prepare the Oscilloscope 1. Remove Top Case. 2. Turn on the power. Then if "Welcome ..." was displayed on the TV monitor, press [ENTER] to advance next stage. Then press [ENTER] and proceed to step 6.
Page 67
(*After "EPG" has been set up, this indication will not appear.) 3. Press [FUNCTIONS]. 4. Select "TV GUIDE", and then press [ENTER]. 5. Press [ENTER] to advance next stage. 6. Press [ENTER] to advance next stage. 7. Select "USA", and then press [ENTER]. 8.
Page 68
V: DC range, and 1V/div. T: 1msec. /div. 11.1.3. Checking and Repairing of RAM / Digital P.C.B. Module 11.1.4. Checking and Repairing of HDD...
Page 69
11.2. Caution for Replacing Parts 11.2.1. Notice for replacing parts of VHS Mechanism 11.2.1.1. Regarding change of parts of VHS mechanism...
Page 70
11.2.2. Notice for Replacing Capstan Motor 11.2.3. Items that should be done after replacing parts...
Page 71
Note2: Please prepare latest firmware updating disc. * Main Firm is being recorded in HDD, but new HDD has no data. Writing Procedure of Main Firm: <<Caution>> (1) Writing of Main Firm needs 3, 4 minutes. (2) Never cut the power of DVD Recorder until writing in Firmware ends. (3) Initial settings and contents of reservation will not change if writing is normally completed.
Page 72
13. After [UNFORMAT] was displayed, message to request FORMAT is displayed on TV screen. 14. Select [Yes] and press [ENTER] key to format HDD. (After FORMAT, program in HDD will be lost, but Main firm will not be lost. “Write of the main farm" is completed above. * Drive firm is not updated by above operation.
Page 74
Turn on the power, and confirm items pointed Items pointed out should reappear. out. Insert RAM disc. The Panasonic RAM disc should be recognized. Enter the EE (TU IN / AV IN - AV OUT) mode. No abnormality should be seen in the picture, sound or operation.
Item Contents Check Item Contents Block noise Distorted sound Crosscut noise Noise (static, background noise, etc.) Picture Sound Dot noise The sound level is too low. Picture disruption The sound level is too high. Not bright enough The sound level changes. Too bright Flickering color Color fading...
Page 77
14. Printed Circuit Board 14.1. Power & Digital I/F P.C.B. 14.1.1. Power & Digital I/F P.C.B. 14.1.2. Power & Digital I/F P.C.B. Address Information 14.2. Main P.C.B. 14.2.1. Main P.C.B. (1/4 Section) 14.2.2. Main P.C.B. (2/4 Section) 14.2.3. Main P.C.B. (3/4 Section) 14.2.4.
Page 78
INITIAL/LOGO ABBREVIATIONS A0~UP ADDRESS ACLK AUDIO CLOCK AD0~UP ADDRESS BUS ADATA AUDIO PES PACKET DATA ADDRESS LATCH ENABLE AMUTE AUDIO MUTE AREQ AUDIO PES PACKET REQUEST AUDIO RF SERVO AMP INVERTED INPUT SERVO AMP OUTPUT ASYNC AUDIO WORD DISTINCTION SYNC BIT CLOCK (PCM) BCKIN BIT CLOCK INPUT...
Page 79
INITIAL/LOGO ABBREVIATIONS DACCK D/A CONVERTER CLOCK DEEMP DEEMPHASIS BIT ON/OFF DEMPH DEEMPHASIS SWITCHING DIG0~UP FL DIGIT OUTPUT DATA INPUT DMSRCK DM SERIAL DATA READ CLOCK DMUTE DIGITAL MUTE CONTROL DROP OUT DOUT0~UP DATA OUTPUT DATA SLICE RF (BIAS) DROP OUT SIGNAL DRPOUT DATA REQUEST DREQ...
Page 80
INITIAL/LOGO ABBREVIATIONS IECOUT IEC958 FORMAT DATA OUTPUT IPFRAG INTERPOLATION FLAG IREF I (CURRENT) REFERENCE ISEL INTERFACE MODE SELECT LDON LASER DIODE CONTROL LASER POWER CONTROL LRCK L CH/R CH DISTINCTION CLOCK MA0~UP MEMORY ADDRESS MEMORY CLOCK MCKI MEMORY CLOCK INPUT MCLK MEMORY SERIAL COMMAND CLOCK...
Page 81
INITIAL/LOGO ABBREVIATIONS READ ENABLE RFENV RF ENVELOPE RF PHASE DIFFERENCE OUTPUT (CD-ROM) REGISTER SELECT RSEL RF POLARITY SELECT RESET RESERVE SBI0, 1 SERIAL DATA INPUT SBO0 SERIAL DATA OUTPUT SBT0, 1 SERIAL CLOCK SERIAL DATA CLOCK SCKR AUDIO SERIAL CLOCK RECEIVER SERIAL CLOCK SCLK...
Page 82
SUB CODE Q DATA SYSCLK SYSTEM CLOCK INITIAL/LOGO ABBREVIATIONS TRACKING ERROR TIBAL BALANCE CONTROL BALANCE OUTPUT 1 BALANCE INPUT BALANCE INPUT BALANCE OUTPUT 2 TPSN OP AMP INPUT TPSO OP AMP OUTPUT TPSP OP AMP INVERTED INPUT TRCRS TRACK CROSS SIGNAL TRON TRACKING ON TRSON...
Page 83
INITIAL/LOGO ABBREVIATIONS X' TAL XALE X ADDRESS LATCH ENABLE XAREQ X AUDIO DATA REQUEST XCDROM X CD ROM CHIP SELECT X CHIP SELECT XCSYNC X COMPOSITE SYNC X DATA STROBE XHSYNCO X HORIZONTAL SYNC OUTPUT XHINT XH INTERRUPT REQUEST X' TAL OSCILLATOR INPUT XINT X INTERRUPT X MEMORY WRITE ENABLE...
Page 84
17.1.2. Casing Parts & Mechanism Section 2...
Page 87
17.2. Replacement Parts List Notes: *Important safety notice: Components identified by mark have special characteristics important for safety. Furthermore, special parts which have purposes of fire-retardant (resistors), high-quality sound (capacitors), low-noise (resistors), etc. are used. When replacing any of components, be sure to use only manufactures specified parts shown in the parts list.
Page 88
of this assembly in production, it will no longer be available. *“(IA)”, mark in Remarks indicate language of instruction manual. [(IA): English] *All parts are supplied by PAVC-CSG. Ref. No. Part No. Part Name & Description Remarks VEP06G25BT MAIN P.C.B. B7501 CR2354-1GUF LITHIUM BATTERY...
Page 120
Ref. No. Part No. Part Name & Description Remarks VKA0382 LEG CUSHION RMC0672 PLATE SPRING RMY0357 HEAT SINK RYP1317A-S1 FRONT PANEL ASS’Y 1 36-1 RXQ1409A DUB BUTTON ASS’Y 36-2 RGK1995-W SD ORNAMENT 36-3 RGL0687-Q SD PANEL LIGHT 36-4 RGQ0445-W SD REFLECTOR 36-5 RYF0784A-S DOOR ASS’Y...
Page 121
Ref. No. Part No. Part Name & Description Remarks VML3934 MAIN LEVER VML3933 PINCH CHARGE ARM VML3632 IDLER ARM VMX3092 P4 CAP VXA7105 S SHAFT HOLDER VXA7106 T SHAFT HOLDER L1AE00000044 AC HEAD ASS’Y 122-1 VHD1066-2 SCREW 122-2 VHD1185 SCREW VXL3107 S LOADING ARM VXL3108...
Page 122
Ref. No. Part No. Part Name & Description Remarks 18. Schematic Diagram for printing with A4...
IIC CLOCK 71 IIC CLOCK TO/FROM VIDEO IC(IC3001)/ AUDIO IC(IC4501) TL24 IIC DATA IIC DATA 79 S.REEL TL23 Q1501 D1501 Q1502 S1531 TAKE-UP SENSOR SUPPLY SAFETY DMR-EH75VP TAB SW PHOTO PHOTO 80 T.REEL SENSOR SENSOR System Control & Servo Block Diagram...
Page 124
SD SEL LED Q7701 (SDI LED DRIVE) D7701 FAN MOTOR P37001 P37001 P31903 P6003 FAN LOCK P6001 P31905 PS31902 PP7701 VHS LED 68 Q7702 (VHS LED DRIVE) D7702 P59001 P37101 P31904 P6002 SCLK DIGITAL 6 TBUS CLK P.C.B. DMR-EH75VP Timer Block Diagram...
Page 135
R37003 ON[H] 2SD0874A0L C45001 TO FAN MOTOR K31005 R37001 P37001 R37002 VWJ0795=5 K1KA03AA0301 FANOUT1 K31006 FANLOCK1 VWJ0795=5 C45017 VWJ0795=5 C45018 VWJ0795=5 DIGITAL I/F SECTION DMR-EH75VP (3/4) Digital I/F(1/4) Section L M N O (Power & Digital I/F P.C.B.(2/2)) Schematic Diagram(IF)
Page 136
NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. R37009 DMR-EH75VP DIGITAL I/F SECTION (4/4) Digital I/F(2/4) Section...
Page 137
P:Power Supply Section:(Page: IF:Digital I/F Section:(Page: NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. DMR-EH75VP THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE Digital I/F(3/4) Section SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 138
VOUT IC38001 C0EBE0000504 NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. DMR-EH75VP THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. Digital I/F(4/4) Section (Power & Digital I/F P.C.B.(2/2))
Page 139
KEY 1 K1KA10B00196 PP4801 TO MAIN P.C.B. DMR-EH75VP NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE Front (L) SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 140
R7717 R7716 100K 100K NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. DMR-EH75VP THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE Front(R) SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. Schematic Diagram...
Page 141
1 2 C56140 FL56106 J0JHC0000032 NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. DMR-EH75VP THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. HDMI Schematic Diagram...
Page 145
MUTE V-SW R CH C1 IN IIC BUS INTERFACE P-ON V-SW MUTE Y1 IN P-ON IC3701 Detail Block Diagram MUTE C/S DET1 IC4801 Detail Block Diagram IC7301 Detail Block Diagram TUNER IN IC7402 Detail Block Diagram DMR-EH75VP IC-Detail Block Diagram...
Page 146
KEY2 S-VHS KEY1 VHS LED VHS LED SD SEL LED SD SEL LED SD LED SD LED SST6V DUB LED DUB LED DVD LED DVD LED HDD LED HDD LED Front (R) P.C.B. Front (L) P.C.B. DMR-EH75VP Interconnection Schematic Diagram...
Page 147
R656 OUT1 R656 OUT0 R656 OUT0 SD Card / DV Jack P.C.B. HDMI P.C.B. DMR-EH75VP DMR-EH75VP NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERING. Interconnection Interconnection THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST, AND MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 149
K7410 VWJ0795=17.5 A_GND TU7401 ENGF6503GRF QR7401 UNR511200L 5V/A_IN NC/CH SW R7402 100K Q7402 2SD1819A0L NC/TV VCR NC/V_IN R7410 0[22] R7411 0[22] DMR-EH75VP I/O TUNER SECTION I/O Tuner(2/4) Section (4/4) AM AN AO AT AU AV AW (Main P.C.B.(4/4)) Schematic Diagram(I)
Page 150
NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. DMR-EH75VP I/O Tuner(3/4) Section (Main P.C.B.(4/4)) Schematic Diagram(I)
Page 151
NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. A:VHS Audio Section:(Page: THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE DMR-EH75VP SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. S:Syscon/Servo/Timer Section:(Page: I/O Tuner(4/4) Section I:I/O Tuner Section:(Page: (Main P.C.B.(4/4))
Page 152
WHEN REPLACING ANY OF THESE COMPONENTS.ONLY THE SAME TYPE. R11220 R11201 47K[22] 9100[22] C11204 R11202 10K[22] 0.1[KB][22] D11203 R11203 13K[G][22] IC11201 RADIATION MA2J11100L ZA11201 VSC5606 R11222 R11223 ZA11202 XYN3+J8FJ 360[G][22] 6800[G][22] DMR-EH75VP POWER SUPPLY SECTION (3/4) Power Supply (1/4) Section (Power & Digital I/F P.C.B.(1/2)) Schematic Diagram(P)
Page 153
R11604 UNR521300L 51K[22] DR_PON_H MGND DMR-EH75VP NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. POWER SUPPLY SECTION Power Supply (2/4) Section THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 154
NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. P:Power Supply Section:(Page: DMR-EH75VP IMPORTANT SAFETY NOTICE: COMPONENTS IDENTIFIED WITH THE MARK HAVE THE SPECIAL CHARACTERISTICS FOR SAFETY.
Page 155
C11722 R11801 ECJGVB1H103K 51K[22] P:Power Supply Section:(Page: DMR-EH75VP IMPORTANT SAFETY NOTICE: NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. Power Supply (4/4) Section THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE COMPONENTS IDENTIFIED WITH THE MARK HAVE THE SPECIAL CHARACTERISTICS FOR SAFETY.
Page 156
0.01 (OPEN) (DV JACK) NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. DMR-EH75VP THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. SD Card/DV Jack...
Page 158
Q1501 D1501 Q1502 THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE PNB2303M01VT B3EA00000072 PNB2303M01VT SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. DMR-EH75VP SYSCON/SERVO Syscon/Servo/Timer(2/4) Section TIMER SECTION (Main P.C.B.(3/4)) AA AB AD AE AF (4/4)
Page 159
I:I/O Tuner Section:(Page: NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE DMR-EH75VP SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. Syscon/Servo/Timer(3/4) Section (Main P.C.B.(3/4))
Page 160
I:I/O Tuner Section:(Page: TO CAPSTAN DRIVE UNIT NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. DMR-EH75VP THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE Syscon/Servo/Timer(4/4) Section SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
13 Schematic Diagram 13.1. Interconnection Schematic Diagram P2571 CAP R/F CAP R/F TU7401 U/V TUNER (FOR VTR) CAP VM CAP VM 5V / A IN NC / CH SW CAPSTAN DRIVE UNIT NC / TV VCR P4001 NC / V IN FULL E FULL E FULL E...
Page 164
AD 5V AD 5V KEY2 KEY1 VHS LED VHS LED SD SEL LED SD SEL LED SD LED SD LED SST6V DUB LED DUB LED DVD LED DVD LED HDD LED HDD LED Front (R) P.C.B. DMR-EH75VP Interconnection Schematic Diagram...
Page 165
DGND DGND TPA+ TPA+ DGND DGND D3.2V 3.3V 3.3V D3.8V 3.3V 3.3V HDMI CONT DAT2 DAT2 HDMI MONI DAT3 DAT3 HOT PLUG HDMI P5 ON H HDMI P3 ON H DAT0 DAT0 DAT1 DAT1 SD Ca DMR-EH75VP Interconnection Schematic Diagram...
Page 166
R656 OUT0 R656 OUT0 SD Card / DV Jack P.C.B. HDMI P.C.B. DMR-EH75VP NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERING. Interconnection THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST, AND MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 167
13.2. Power Supply (1/4) Section (Power & Digital I/F P.C.B.(1/2)) Schematic Diag LOCATION MAP ZA11101 ZA11102 L11101 EYF52BCY EYF52BCY #G0B832L00001 K3GE1ZA00010 K3GE1ZA00010 G0B832F00003 C11106 #ECQU2A223MLC ECQU2A223MLA F11101 K5D202BK0005 K5D202BLA013 P11101 250V2A K2AB2B000008 SEE THE K2AB2B000010 R11101 SERVICE MANUAL ERDS1TJ474 470K[1/2W] (UL RECOGNIZED) P:Power Supply Section:(Page: IF:Digital I/F Section:(Page:...
C0DBAZZ00131 QR11604 UNR521300L DR_PON_H MGND DMR-EH75VP NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. Power Supply (2/4) Section ER SUPPLY SECTION THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 171
13.4. Power Supply (3/4) Section (Power & Digital I/F P.C.B.(1/2)) Schematic Diag POWER SUPPLY SECTION (1/4) IC11202 RADIATION ZA11301 VSC5606 IC11301 ZA11302 XYN3+J8FJ C0DACZH00030 C11307 F1B3A2720001 ECKW3A272KRP 2700P[1KV] LOCATION MAP NOTE:DO NOT USE THE PART NUMB THE CORRECT PART NUMBER SLIGHTLYDIFFERNT OR AMEN IMPORTANT SAFETY NOTICE: COMPONENTS IDENTIFIED WITH TH...
O NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. HE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE IGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. P:Power Supply Section:(Page: DMR-EH75VP ANT SAFETY NOTICE: NENTS IDENTIFIED WITH THE MARK HAVE THE SPECIAL CHARACTERISTICS FOR SAFETY.
C0DBAZZ00131 C11721 VREF F1J1C105A091 C11722 ECJGVB1H103K P:Power Supply Section:(Page: DMR-EH75VP TANT SAFETY NOTICE: Power Supply (4/4) Section ONENTS IDENTIFIED WITH THE MARK HAVE THE SPECIAL CHARACTERISTICS FOR SAFETY. IF:Digital I/F Section:(Page: REPLACING ANY OF THESE COMPONENTS.ONLY THE SAME TYPE. (Power & Digital I/F P.C.B.(1/2))
Page 175
IC11201 IC11602 SWITCHING IC RESET IC IC-DETAIL BLOCK DIAGRAM IC-DETAIL BLOC DRAIN UVLO UVLO START-UP LATCH RELEASE/ CIRCUIT OVER VOLTAGE PROTECTOR/ Vref VCC(START) VCC(STARTUP OFF) OVER HEATING /VCC(STOP) /VCC(STARTUP ON) PROTECTOR IDP(LIMIIT/ BURST)SENS. ZERO CURRENT DET./ONDEAD TIMER CONTROL SOFT-DRIVE CIRCUIT CIRCUIT STANDBY CIRCUIT...
13.6. Digital I/F (1/4) Section (Power & Digital I/F P.C.B.(2/2)) Schematic Diagram (IF) LOCATION MAP P:Power Supply Section:(Page: IF:Digital I/F Section:(Page: IC37001 FAN MOTOR DRIVE IC-DETAIL BLOCK DIAGRAM NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 178
(IF) IC45001 X SW+6V SWITCHING REG. IC-DETAIL BLOCK DIAGRAM VOUT VOUT ON[H] C45001 C45017 VWJ0795=5 C45018 VWJ0795=5 DMR-EH75VP Digital I/F(1/4) Section L M N O (Power & Digital I/F P.C.B.(2/2)) Schematic Diagram(IF)
NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. R37009 DMR-EH75VP Digital I/F(2/4) Section Z AA AB AC AD AE (Power &...
IF:Digital I/F Section:(Page: LOCATION MAP NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. DMR-EH75VP THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE Digital I/F(4/4) Section SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
13.12. Syscon/Servo/Timer (1/4) Section (Main P.C.B.(3/4)) Schematic Diagram (S) LOCATION MAP NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. V:Video Section:(Page: THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. A:VHS Audio Section:(Page: S:Syscon/Servo/Timer Section:(Page: I:I/O Tuner Section:(Page:...
I:I/O Tuner Section:(Page: NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. DMR-EH75VP Syscon/Servo/Timer(2/4) Section (Main P.C.B.(3/4)) Schematic Diagram(S)
A:VHS Audio Section:(Page: S:Syscon/Servo/Timer Section:(Page: I:I/O Tuner Section:(Page: CAPSTAN DRIVE UNIT DMR-EH75VP NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE Syscon/Servo/Timer(4/4) Section SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 197
IC2001,6301 +5V SWITCHING REG. IC-DETAIL BLOCK DIAGRAM VOUT IC2501 LOADING/CYLINDER MOTOR DRIVE IC-DETAIL BLOCK DIAGRAM OUT 1 F IN CONTROL PRE-DRIVE LOGIC OUT 2 R IN MOTOR MOTOR DRIVE DIFFERENTIAL PRE-DRIVE SELECTOR DRIVE SIGNAL AMPLIFIRE GENERATOR VCC 19 DIFFERENTIAL FG/PG DIFFERENTIAL AMPLIFIRE COMPOSER...
13.16. I/O Tuner Section (1/4) (Main P.C.B.(4/4)) Schematic Diagram (I) JK4801 K1U407B00004 LOCATION MAP NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. V:Video Section:(Page: A:VHS Audio Section:(Page: S:Syscon/Servo/Timer Section:(Page:...
13.17. I/O Tuner Section (2/4) (Main P.C.B.(4/4)) Schematic Diagram (I) LINE LINE LINE LINE IN1[R] IN3[R] IN1[L] IN3[L] L1 IN L3 IN CPN L1 IN CPN L3 IN C3918 R3928 R3930 R3929 C3919 0.01 C3743 1u[KB] 6.3V R3910 6.3V C3741 1u[KB] 6.3V C3742...
Page 202
SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. C3738 1u[KB] 6.3V C3737 1u[KB] 6.3V IC3702 C1AB00001486 K7410 VWJ0795=17.5 A_GND TU7401 ENGF6503GRF 5V/A_IN NC/CH SW NC/TV VCR NC/V_IN R7410 0[22] R7411 0[22] DMR-EH75VP I/O Tuner(2/4) Section ECTION (Main P.C.B.(4/4)) AM AN AO AT AU AV AW Schematic Diagram(I)
13.19. I/O Tuner Section (4/4) (Main P.C.B.(4/4)) Schematic Diagram (I) I/O TUNER SECTION (2/4) LB7407 ERJ3GEY0R00V R7401 1K[D] C7401 D7401 50V1 B0BA03000015 MAZ4300NMF R4830 100K R4831 220K R4832 100K C4834 R4840 16V220[M] L7301 VWJ0795=5 FL7301 J0B4504AA026 R7310 R7311 NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR OR THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND M SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREP...
Page 206
Q7401 2SB1218A0L LOCATION MAP V:Video Section:(Page: N ON THIS DRAWING FOR ORDERRING. A:VHS Audio Section:(Page: N IN THE PARTS LIST,AND MAY BE DMR-EH75VP E THIS DRAWING WAS PREPARED. S:Syscon/Servo/Timer Section:(Page: I/O Tuner(4/4) Section I:I/O Tuner Section:(Page: (Main P.C.B.(4/4)) Schematic Diagram(I)
Page 207
IC3701 VIDEO/AUDIO PROCESSOR IC-DETAIL BLOCK DIAGRAM C-SW C75 OUT DVD C IN 6.7M C75 SAG S1/S2 BIAS V-SW DVD Y IN Y/C MIX 6.7M Y/Py/G-SW Y-SW Y75 OUT DVD G/Py IN Py/G-SW Py/G OUT 6.7MLPF 13.5MLPF Pb/B-SW Pb/B OUT DVD B/Pb IN 6.7M BIAS Pr/R-SW...
Page 210
J0JHC0000032 LB56110 FL56106 J0JHC0000032 NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. DMR-EH75VP E CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE GHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. HDMI Schematic Diagram...
R66815 C66801 0.01 NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. DMR-EH75VP THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. SD Card/DV Jack Schematic Diagram...
Page 216
R7721 7702 100K D0601A0L NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. DMR-EH75VP THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE Front(R) SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. Schematic Diagram...
13.23. Front Jack Schematic Diagram R7806 8200 R7801 3900 R7805 R7802 3900 2700 R7803 3900 R7804 2700 S7802 S7810 EVQ11G07K EVQ11G07K CH UP S7803 EVQ11G07K S1 IN JK3802 K1CB104A0017 LB3301 CPN Y IN2 LB3303 ERJ3GEY0R00V ERJ3GEY0R00V CPN C IN2 L2 IN[R] R3801 L2 SW R3802...
Page 218
LB3302 ERJ3GEY0R00V C3801 0.01 R3803 DMR-EH75VP NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE Front (L) SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 228
4.43 NTSC L BILINGUAL 443NT [L] BILINGUAL L A. COMP BIL [L] AUDIO COMPONENT SIGNAL BILINGUAL H BIL. [H] A. COMPO AUDIO COMPONENT SIGNAL BILINGUAL L AUDIO DUBBING PAUSE L BIL/M1 [L] A. D.P [L] AUDIO DUBBING PAUSE L BS CLOCK A.
Page 229
CYL GND CYLINDER GND FULL. E. 12V FULL ERASE 12V DELAIED FM RECORDING H D.F.M. REC [H] GND (ANALOG) GND [A] DELAIED FM RECORDING L D. FM REC [L] GND (TUNER) GND [TU] D. GND GND/NON SW 12V DIGITAL GND GND/N.
Page 230
POWER OFF H LINE IN [R] LINE INPUT (R) P-OFF [H] POWER OFF L LINE OUT [L] LINE OUTPUT (L) P-OFF [L] LINE OUT [R] LINE OUTPUT (R) P. FAIL POWER FAILURE DETECT LP H POWER OFF H LP [H] P.
Page 231
SYSTEM CONTROL 5V RF OUT RF OUTPUT SYSCON 5V SYSTEM SW RF Y RF LUMINANCE SIGNAL SYSTEM TAKE-UP PHOTO TRANSISTOR RF. Y. IN RF LUMINANCE SIGNAL INPUT T-PHOTO TAKE-UP REEL PULSE RF. Y. OUT RF LUMINANCE SIGNAL OUTPUT T-RL. PLS TIMER BUS CLOCK ROTAR.
Page 232
P59001 P37101 P31902 P6004 MUTE DIGITAL AUDIO OUT QR4814 X SW5.8V MIX L OUT DM P59001 P37101 P31902 P6004 MUTE QR4813 FROM PCM/ DIGITAL BITSTREAM QR4814 P.C.B. MUTE P59001 P37101 P31901 P6005 IECOUT IEC OUT DMR-EH75VP Analog Audio Block Diagram...
Page 233
LINE 3V IN V-SW VIDEO IN SLICER VIDEO P6004 P31902 P37101 P59001 CPN C IN3 DIGITAL P.C.B. TU VIDEO IN TUNER IN CPN Y IN3 S-VIDEO IN SYSTEM CONTROL SECTION L3 CS DET L3 CS DET IC6001- DMR-EH75VP Analog Video Block Diagram...
Page 234
EP COM DD CYLINDER SQPB VIDEO HEAD IC4501- P3001 EP R C CLOCK TO C CCD DRIVER SYSTEM CONTROL SECTION Q3001 BUFFER IC6001- SYSTEM CONTROL SECTION SVHS PB DET S-PB IC6001- DMR-EH75VP DMR-EH75VP Analog Video Block Diagram Analog Video Block Diagram...
Page 236
MAIN P.C.B. DP7501- DRAIN 5 IP11703 -29V P31905 P6001 MAIN P.C.B. DP7501 D11306 D11304 Q11301 (FEED BACK) X SW+6V IC11701 (ERROR VOLTAGE DET.) D+12V P37101 P59001 DIGITAL P.C.B. 64,66,68,70,72,74 D+12V UNREG+36V P31902 P6004 MAIN P.C.B. COLD DMR-EH75VP Power Supply Block Diagram...
Page 237
V IN V OUT 1 Q11601 D+12V (DR +12V SELECT SWITCH) DI POWER ON P37101 P59001 FROM DRIVE POWER ON P31903 P6003 MAIN P.C.B. IC7501- 71 QR11601 DMR-EH75VP DMR-EH75VP (DR P ON OUT) Power Supply Block Diagram Power Supply Block Diagram...