DeWalt DCW604NT Manual page 15

EnGLIsH
Installing a Plunge Base Parallel Fence with
Guide Rods, DCW604 Only (Fig. H)
A parallel fence with guide rods may be included with your
plunge base unit. A premium parallel fence (model DE6913)
is also available from your local retailer or service centre at
extra cost.
1. Attach the guide rods 36
2. Attach the thumb screws
3. Tighten the thumb screws
4. Slide the parallel fence
5. Attach thumb screws
37
parallel fence.
6. Tighten the thumb screws temporarily. Refer to Adjusting
the Parallel Fence.
Adjusting the Parallel Fence (Fig. A, H)
Follow the assembly instructions included with the
parallel fence.
1. Draw a cutting line on the material.
2. Lower the router carriage until the cutter is in contact with
the workpiece.
3. Lock the plunge mechanism by releasing the plunge lock
lever 16
4. Position the router on the cutting line. The outer cutting
edge of the cutter must coincide with the cutting line.
5. Slide the parallel fence
tighten the thumb screws
Attaching a Dust Extraction System to the
Fixed Base (Fig. I)
To connect the router to a dust extraction system for dust
collection, follow these steps:
1. Remove the motor unit from the base. Refer to Removing
the Motor from the Fixed Base.
2. Attach dust extraction system attachment accessory
to the base as shown. Tighten thumb screws
by hand.
3. Attach hose adapter to dust extraction system
attachment accessory.
4. When using dust extraction system attachment, be aware
of the placement of the dust extraction system. Be sure that
the dust extraction system is stable and that its hose will not
interfere with the work.
Attaching a Dust Extraction System to the
Plunge Base, DCW604 Only (Fig. J)
1. Remove the motor unit from the base. Refer to Removing
the Motor from the Plunge Base.
2. Slide tab 31 (inset) on dust extraction system
attachment 35 into slot in plunge base and snap tab
(inset) into hole in plunge base.
3. Secure to base with supplied plastic washer
screw . Tighten thumb screw securely by hand.
34
42
to the plunge router base.
and springs to the base.
37 38
37 .
39 over the rods.
and springs to the
38
39 against the workpiece and
37 .
30 securely
33 and thumb
4. Attach hose adaptor to dust extraction system attachment.
When using dust extraction system attachment, be aware of
the placement of the dust extraction system. Be sure the dust
extraction system is stable and its hose will not interfere with
the work.
Set-Up: Fixed Base (Fig. A, K, L)
Inserting the Motor into the Fixed Base
1. Open the locking lever
2. If the depth adjustment ring
thread the depth adjustment ring onto the motor until the
ring is about halfway between the top and bottom of the
motor as shown. Insert the motor into the base by aligning
the groove on the motor
base. Slide the motor down until the depth adjustment ring
snaps into place.
nOTE: Guide pin grooves
the motor so it can be positioned in two orientations.
3. Adjust the depth of cut by turning the depth adjustment
ring. Refer to Adjusting the Depth of Cut.
4. Close the locking lever
achieved. For information on setting the cutting depth, refer
to Adjusting the Depth of Cut.
Adjusting the Depth of Cut (Fig. L)
1. Open the locking lever
ring 5 until the bit just touches the work piece. Turning
the ring clockwise raises the cutting head while turning it
anticlockwise lowers the cutting head.
2. Turn the micro-adjustment scale
on the scale lines up with the pointer on the bottom of the
depth adjustment ring.
3. Turn the depth adjustment ring until the pointer lines up
with desired depth of cut marking on the micro-adjustment
scale 11 .
nOTE: Each mark on the adjustment scale represents a
depth change of 0.4 mm and one full (360º) turn of the ring
29
changes the depth 12.7 mm.
4. Close the locking lever
Removing the Motor from the Fixed Base (Fig. K)
1. Remove the battery pack from the motor. Refer to Installing
and Removing the Battery Pack.
2. Open the locking lever
3. Grasp the motor unit with one hand, depressing both quick
release tabs
4. With the other hand, grasp the base and pull motor from
the base.
Set-Up: Plunge Base, DCW604 Only
(Fig. A, M)
Inserting the Motor into the Plunge Base
32
1. Remove the depth adjustment ring
is not used with the plunge base.
nOTE: Snap depth adjustment ring onto fixed base, when
not in use, to prevent loss.
12 on the base.
5 is not on the motor
6 with the guide pins
are located on either side of
9
12 when the desired depth is
and turn the depth adjustment
12
11 clockwise until the 0
12 to lock the base.
12 on the base.
45 .
5 from the motor
6 ,
17 on the
6 . It