Page 1
Service SR6006 / U1B/N1B/N1SG/K1B Manual AV Surround Receiver • For purposes of improvement, specifications and design are subject to change without notice. • Please use this service manual with referring to the operating instructions without fail. • Some illustrations using in this service manual are slightly different from the actual set. Ver.
SAFETY PRECAUTIONS The following items should be checked for continued protection of the customer and the service technician. LEAKAGE CURRENT CHECK Before returning the set to the customer, be sure to carry out either (1) a leakage current check or (2) a line to chassis resistance check.
NOTE FOR SCHEMATIC DIAGRAM WARNING: Parts indicated by the z mark have critical characteristics. Use ONLY replacement parts recommended by the manufacturer. CAUTION: Before returning the set to the customer, be sure to carry out either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the set is defective.
ZONE SELECT DISPLAY Service Jig When you repair the printing board, you can use the following JIG (Extension cable kit). Please order it from Marantz Official Service Distributor in your region if necessary. 8U-110084S EXTENSION UNIT KIT 1 Set (Refer to 61 page.)
DISASSEMBLY • Disassemble in order of the arrow in the following figure. • In the case of the re-assembling, assemble it in order of the reverse of the following flow. • In the case of the re-assembling, observe "attention of assembling". •...
Page 9
About the photos used for "descriptions of the DISASSEMBLY" section • The shooting direction of each photograph used herein is indicated on the left side of the respective photograph as "Shooting direction: ***". • Refer to the diagram below about the shooting direction of each photograph. •...
1. FRONT PANEL ASSY Proceeding : CABINET TOP FRONT PANEL ASSY → Remove the screws. View from the bottom Cut the wire clamp bands, then disconnect the connector wires and FFC cables. Remove the screws. STYLE PIN : Loosen CN602 TAPE : Remove FFC cable CN390...
2. HEAT SINK ASSY Proceeding : CABINET TOP HEAT SINK ASSY → Remove the screws. View from the bottom Cut the wire clamp bands, then remove the screws. Disconnect the connector wires. Shooting direction: C Shooting direction: D CN602...
Page 12
Cut the wire clamp band, then disconnect the connector wire and FFC cables . STYLE PIN : Loosen HEAT SINK Assy TAPE : Remove FFC cable CN390 FFC cable Disconnect the connector wires. CN461 CN701 CN703 CN702 Please refer to "EXPLODED VIEW" for the disassembly method of each P.W.B included in HEAT SINK ASSY.
3. HDMI UNIT ASSY HDMI UNIT ASSY Proceeding : CABINET TOP → Remove the screws, then remove the BACK PANEL and the HDMI BRACKET. Shooting of photograph: A Cut the wire clamp bands, then disconnect the connector wires and the FFC cables. Remove the PCB DOCK from the PCB SIDE CNT and PCB RS232C(Board to board).
Page 14
Disconnect the connector wire. Remove the screws. CN931 Remove the screws.
Page 15
Cut the wire clamp bands, then disconnect the connector wires. CN941 CN932 CN940 CN903 CN781 Cut the wire clamp band, then disconnect the connector wires. CN461 CN703 CN702 CN701...
Cut the wire clamp bands, then disconnect the connector wires, and remove the screws. CN203 CN902 Remove the screw. Please refer to "EXPLODED VIEW" for the disassembly method of each P.W.B included in HDMI UNIT ASSY. 4. TRANS MAIN Proceeding : CABINET TOP HDMI UNIT ASSY POWER TRANS...
SPECIAL MODE Special mode setting button b No.1 - 4,6 - 9 : Press the ON/STANDBY button to turn on the power while pressing both the button A and the button B at the same time. b No.5 : The AC power cord on while pressing both the button A and the button B at the same time. b No.10 - 13 : Press and hold both buttons A and B for over 3 second with the power turned on.
1. µcom/DSP Version display mode 1.1. Operation specifications µcom/DSP version display mode: When the set is started up in this mode, the version information is displayed. Starting up: Press the "ON/STANDBY" button to turn on the power while pressing the "STATUS" and "ZONE SELECT" buttons. Now, press the "STATUS"...
Page 19
Q2 HD Radio Version : (U Version only) S - * * . * * C * * * * * * * Q3 MultEQ Pro APP Version : A P P * * . * * . * * .
Page 20
1.4. Error display See the following table for each "Error information" display and its explanation (status). Display order is q , w , e , r , t , y , u , i . Condition Status FL Display Trouble shooting •...
Page 21
Status FL Display M A I N A . P L b 1, b 2 * * * * * * * * The written Firmware and product settings (model name, brand name, destination) L - * * . * * * .
2. Errors checking mode (Displaying the protection history) 2.1. Operation specifications Error mode (Displaying the protection history): When the set is started up in this mode, the error information is displayed. Starting up: Press the "ON/STANDBY" button to turn on the power while pressing the "INTERNET RADIO" and "ONE TOUCH PLAY" buttons.
Page 23
2.3. Clearing the protection history There are two ways to clear the protection history, as described below. Start up the set in error (protection display) mode and display the error, then press and hold down the "PURE DIRECT" button for 3 seconds. P R O T E C T H I S T O R Y : D C...
3. DUAL BACKUP MEMORY This product has a Dual Backup Memory function. The conventional Backup functions to memorize, in the EEPROM (IC202) in the circuit, a current setting of the moment the main power is turned off so that it can be restored when it is turned ON again.
4. DIAGNOSTIC MODE (Video/Audio (signal) path confirmation mode) This mode is used for confirming the Video and Audio (signal) paths. (Troubleshooting) Confirming the operation of unit can be easily done after repair. Backup data will not be lost. 4.1. Starting diagnostic mode Press and hold both buttons ZONE SELECT and PURE DIRECT for over 3 second with the power turned on.
Page 27
Details of how to operate remote Output sequence of remote control codes Confirmation item Setting and display Contents of confirmation Remarks controller *a) ※ It is useful to form a macro program. *b) OSD FUNCTION Video Convert(IP Scaler) : ON, All Sources 1.Press [AMP] qZONE2 POWER OFF ·OSD : Display / Output : HDMI...
Page 28
4.5. Audio system confirmation items fig.XX : Refer to the block diagram of the fig.XXth. Details of how to operate remote Output sequence of remote control codes Confirmation item Setting and display Contents of confirmation Remarks controller b It is useful to form a macro program. Analog (signal) Path Input Mode : Fixed ANALOG 1.Press [AMP]...
Page 29
Details of how to operate remote Output sequence of remote control codes Confirmation item Setting and display Contents of confirmation Remarks controller b It is useful to form a macro program. Analog Audio (signal) Path Amp assign : ZONE2 1.Press [AMP] qZONE2 POWER OFF ·Input : Analog / Output : Speakers (SURR BACK L/R) (ZONE2)
Page 32
fig.2 (2/2) SR6006 HDMI VIDEO BLOCK IC121 IC151 IC101 HDMI IN ADV7844 ADV8002-1 AD8195 Port A Buffer HDMI FRONT IN Port B HD_PCLK IC111 HDMI IN1 HD_HSYNC HD_VSYNC ADV3002 VIDEO HD_DE Port C HDMI OUT1 HD/CS HD_SFL VS/FIELD HD_P[0:35] PROCESSING HDMI IN2 FIELD/DE HDMI OUT2...
Page 33
fig.3 SR6006 HDMI VIDEO BLOCK IC121 IC151 IC101 HDMI IN ADV7844 ADV8002-1 AD8195 Port A Buffer HDMI FRONT IN Port B HD_PCLK IC111 HDMI IN1 HD_HSYNC ADV3002 HD_VSYNC VIDEO HD_DE Port C HDMI OUT1 HD/CS HD_SFL PROCESSING VS/FIELD HD_P[0:35] HDMI IN2 FIELD/DE HDMI OUT2 Port D...
Page 35
fig.4 (2/2) SR6006 HDMI VIDEO BLOCK IC121 IC151 IC101 HDMI IN ADV7844 ADV8002-1 AD8195 Port A Buffer HDMI FRONT IN Port B HD_PCLK IC111 HDMI IN1 HD_HSYNC ADV3002 HD_VSYNC VIDEO HD_DE Port C HDMI OUT1 HD/CS HD_SFL PROCESSING VS/FIELD HD_P[0:35] HDMI IN2 FIELD/DE HDMI OUT2...
Page 36
fig.5 (1/2) SR6006 HDMI VIDEO BLOCK IC121 IC151 IC101 HDMI IN ADV7844 ADV8002-1 AD8195 Port A Buffer HDMI FRONT IN Port B HD_PCLK IC111 HDMI IN1 HD_HSYNC HD_VSYNC ADV3002 VIDEO HD_DE Port C HDMI OUT1 HD/CS HD_SFL VS/FIELD HD_P[0:35] PROCESSING HDMI IN2 FIELD/DE HDMI OUT2...
Page 38
fig.6 SR6006 HDMI VIDEO BLOCK IC121 IC151 IC101 HDMI IN ADV7844 ADV8002-1 AD8195 Port A Buffer HDMI FRONT IN Port B u-COM HD_PCLK IC111 HDMI IN1 HD_HSYNC HD_VSYNC ADV3002 VIDEO HD_DE Port C HDMI OUT1 HD/CS HD_SFL VS/FIELD HD_P[0:35] PROCESSING HDMI IN2 FIELD/DE HDMI OUT2...
Page 39
fig.7 SR6006 HDMI VIDEO BLOCK IC121 IC151 IC101 HDMI IN ADV7844 ADV8002-1 AD8195 Port A Buffer HDMI FRONT IN u-COM Port B HD_PCLK IC111 HDMI IN1 HD_HSYNC ADV3002 HD_VSYNC VIDEO HD_DE Port C HDMI OUT1 HD/CS HD_SFL PROCESSING VS/FIELD HD_P[0:35] HDMI IN2 FIELD/DE HDMI OUT2...
Page 40
fig.8 (1/2) SR6006 ANALOG AUDIO BLOCK H/P OUT EXTFL EXTFR AMP/PRE ANA_FL AMPFL SPK OUT DAFL TONE EXTC EXTFL EXTSW AMPFR V.AUX AMP/PRE ANAFR ADINL/R EXTSL DAFR DAZONE2 TONE EXTFR EXTSR DAZONE3 FL_B EXTBSL AMP/PRE EXTBSR EXTC Pull down FR_B Pull down DASW AMP/PRE...
When you repair the printing board, you can use the following JIG (Extension cable kit). Please order it from Marantz Official Service. Distributor in your region if necessary. NOTE: The incorrect connection with in the JIG (EXTENSION UNIT KIT) may cause damage.
Page 62
(2) Disconnect the connector board. Board to board Board to board PCB HDMI Board to board Board to board CN931 PCB VIDEO Board to board PCB INPUT Board to board...
Page 63
(3) Detach PCB HDMI from the chassis, and turn it over. Please put an insulation sheet that is larger than PCB HDMI under PCB. b Connect the ground point of PCB to the chassis with a ground lead or the like. VIDEO PCB HDMI PCB AUDIO PCB...
Page 64
PCB FRONT CNT Insulation sheet PCB SIDE CNT PCB INPUT Connection table of Board to Board Ref. No. Ref. No. 11 pin CN28A SIDE CNT CN28B HDMI 21 pin CN27A SIDE CNT CN27B HDMI 27 pin CN24A FRONT CNT CN24B HDMI 15 pin CN26A...
WHEN THE MICROPROCESSOR IS REPLACED WITH A NEW ONE When the U-PRO (Microprocessor) or the Flash ROM is replaced, confirm the following. After PWB Name Ref. No. Description Remark replaced HDMI IC201 R5F5630ECDFB SOFTWARE: Main HDMI IC231 R5F3650KNFB SOFTWARE: Sub HDMI IC410 MX29LV160DBTI-70G...
Page 66
--- Cautions on Firmware Update --- • In order to update the firmware, you must have the correct system requirements and settings for a broadband Internet connection. • Do not turn off the power until updating is completed. Even with a broadband connection to the Internet, approximately 1 hour is required for the updating procedure to be completed.
Page 67
Error Display Details of Error code Coping strategies Code (Eight digits or more are the scrolling displays.) Check the network connection. C o n n e c t i o n F a i l Connection to DPMS failed. Carry out the update in an environment (can not get NTP) that has little network load.
Page 68
Error Display Details of Error code Coping strategies Code (Eight digits or more are the scrolling displays.) M a i n Log-in to DPMS failed when Main Carry out the update in an environment L o g i n CPU was rewritten. that has little network load.
Page 69
Error Display Details of Error code Coping strategies Code (Eight digits or more are the scrolling displays.) Downloading firmware failed after Turn off and on the power. D S P the log-in to DPMS when firmware Updating starts automatically. D o w n l o a d such as Sub CPU, DSP and PLD Carry out the update in an environment was rewritten.
Page 70
Error Display Details of Error code Coping strategies Code (Eight digits or more are the scrolling displays.) G U I Receiving firmware for rewriting Turn off and on the power. serial flash sent by DM860 failed U p d a t i n g Updating starts automatically.
Page 71
Error Display Details of Error code Coping strategies Code (Eight digits or more are the scrolling displays.) Firmware download error message Turn off and on the power. E I M G received (connection failure) when Updating starts automatically. D o w n l o a d DM860 related firmware was Carry out the update in an environment rewritten (Boot Loader Mode).
ADJUSTMENT Audio Section Adjusting Idling Current Required measurement equipment: DC Voltmeter 1. Preparation (1) Avoid direct blow from an air conditioner or an electric fan, and adjust the unit at normal room temperature 15 °C ~ 30 °C (59 °F ~ 86 °F). (2) Presetting •...
TROUBLE SHOOTING 1. POWER 1.1. Power not turn on Power not turn on. When the power turned on, When the power turned on, does the ON/STANDBY does the ON/STANDBY indicator on the front panel indicator on the front panel flashing green? flashing red? Is the fuse blown? Refer to 1.2.Fuse is blown.
2. Analog video Perform the operation below beforehand. b Check that the connection cable and the Monitor are normal. b Set VIDEO CONVERT ON. b Set COMPONENT signal to 480i. b Set Function to the following. V : SAT COMPONENT : DVD MONITOR OUT (CVBS/Cmponent) output NG Input Input...
Page 79
Input CVBS,COMPONENT Is the power supply voltage REGULATOR B'D flaw. correctly output? VIDEO B'D and REGULATOR V+5V : CN931-4pin B'D and connection of the wire V-5V : CN931-1pin are defective. Check on set value of each IC. Is they the following voltage values? HDMI B'D flaw.
Page 80
VIDEO B'D flaw. Extend HDMI B'D using a jig. Is the signal output from Is the signal input to IC551(AVDM-2000)? IC551(AVDM-2000)? The parts between IC551 and : J5227/J5137 : J5195 COMPONENT(Y) : J5134/J5133 COMPONENT(Y) : J5241 JK551 or JK557 are defective. COMPONENT(Cb) : J5135 COMPONENT(Cb) : J5233 COMPONENT(Cr) : J5136...
Page 81
I2C communication wave form CH1: CLK CH1: DATA...
Page 82
HDMI test point (COMPONENT SIDE) Detail A COMP_DET En_CVBS En_Y VSDA VSDA V_DET En_Pr En_Pb Detail B COMPONENT(Cr) COMPONENT(Cb) COMPONENT(Y)
Page 83
VIDEO test point JK 554 1.DIN_SA T_Y 2.V G N D 3.DIN_SA T_CB 4.V G N D C 5106 C 5108 C 5102 C 5104 5.DIN_SA T_CR 1.M O N_CO M P _Y_O UT 6.V G N D 2.V G N D 7.SA T_LIN E1 3.M O N_CO M P _CB_O UT 8.SA T_LIN E2...
(6) Is the BD/DVD player's HDMI output setting correct? the BD/DVD player's operating instructions. (7) When you use a Marantz BD/DVD player's, is the fluorescent display tube's "HDMI" indicator lit? If you use a non-Marantz BD/ DVD player's, proceed to "YES".
Page 85
Check TV Use an HDCP-compatible TV. PC TVs (11) Is the TV HDCP-compatible? cannot be used. If the TV is not compatible with resolutions of 1080P, no picture will be output, even (12) Is the TV compatible with resolutions of 1080P? if the BD/DVD player's resolution is set to 1080P.
Page 86
/JK113/JK114/JK121/ display's "HDMI" indicator lit? voltage of the HDMI connector for the input on the JK122) to the IC If using a non-Marantz BD/ side on which the BD/DVD player is connected. (IC101/111/121) is DVD player, proceed to "NO". Is communication waveform confirmed in defective.
Page 87
Check operation of IC121(ADV7844). (25) Check power supply. Are 1.8V supplied to L1202/L1203/L1204/L1205? The power supply circuitry is defective. Are 3.3V supplied to L1201/L1206/L1207? (26) Check xtal oscillator. The X1201 or IC121 is defective. Is oscillation of X1201(28.6363MHz) transmitted? (27) Check RESET. Is RESET waveform confirmed in TP[7844_RESET], when power The RESET circuitry or IC121 is defective.
Page 88
3.2. HDMI test point and waveforms (COMPONENT SIDE) Detail A TX1_D1- TX1_CK- TX2_D1- TX2_CK- TX1_D1+ TX1_CK+ TX2_D1+ TX2_CK+ DDC_DATA DDC_CLKHPD TX2_D0- TX1_D2+ TX2_D0+ TX1_D2- TX1_D0- TX2_D2- TX1_D0+ TX2_D2+ DDC_DATA DDC_CLKHPD Detail B DDC_CLK HPD DDC_DATA...
Page 90
DDC_CLK/DDC_DATA/TMDS : Check items (17)/(19)/(24)/(32) 0.9V DDC_CLK 2.48V TMDS Waveform DDC_DATA Timing waveform illustration from the start of CEC3.3V to when reset is released : Check items (22) CEC3.3V 338ms 3002_RESET Controlled waveform(I2C), when power is turned on : Check items (23) HDMI_SCL HDMI_SDA POWER ON...
Page 91
Timing waveform illustration from the start of CEC3.3V to when reset is released : Check items (27) CEC3.3V 338ms 7844_RESET Timing waveform illustration from the start of CEC3.3V to when reset is released : Check items (31) DV3.3V 314ms 8002_RESET DV3.3V 10ms 10ms...
4. AUDIO 4.1. AUDIO CHECK Audio output NG. Refer to "Audio Check PATH" (101 page). CHECK1 INPUT SURROND MODE SOURCE Check ANALOG audio BLOCK. Audio output OK? ANALOG 2CH DIRECT ANALOG CHECK2 INPUT SURROND MODE SOURCE Check Digital audio BLOCK. Legacy Audio output OK? COAX or OPT...
Page 94
4.2. Power AMP (MAIN UNIT) No sound is output. The protector operates. Is the power transistor open or short- circuited? Replace the power transistor. 2SB1647/2SD2560 Is the emitter resistance of the power transistor open? Replace the emitter resistance. 0.47Ω Is the base resistance of the power transistor open? Replace the base resistance.
Page 95
4.3. Analog audio No sound is output Is the voltage of ±8V supplied to The power supply of ±8V is repaired. SIDE CNT B'D CN41A 4-7pin? Is the audio signal transmitted to The power amplifier is repaired. INPUT B'D CN461? Connect the connectors properly.
5. Network/USB 5.1. Cannot connect to network Checking the environment Check the LAN cable properly then turn the Is the LAN cable properly connected? power back on. Checking the settings Set the IP address and other parameters properly. For a fixed IP setting, check Are the AV RECEIVER's network settings correct? whether the IP address is redundant with that of other devices, and check whether the...
Page 97
5.2. USB device is not recognized Checking the USB device Are you using a USB hub? Don't use the USB hub. Only mass storage devices in FAT16 or FAT32 formats or MTPcompatible devices Is the USB device compatible with the set? and iPod (Remove some models) are supported.
Page 98
HDMI test point CN321 Q3200 IC323 IC406 IC322 IC390 IC304 IC301 CN903 (COMPONENT SIDE) USB test point C U P 12383-3 C 6109 BN605 B N605 C 6068 V BUS BK602 BK 602 USBD+ USBD- DG ND DG ND LUG 67 (COMPONENT SIDE)
6. SMPS DC 5V is not output. Is there damage in IC901 Replace the IC901(TOP258MG) and (TOP258MG)? D9001/D9002/D9003/D9004. Is there the damage in D9001/D9002/ Is the fuse (F9001) blown? Replace the parts of damage. D9003/D9004/C9004? Is there solder short circuit in the PWB The solder short part of the PWB board board? is repaired.
Page 100
Operation waveform for each part After primary side rectification (Caution: High voltage, electric shock) Primary drain (Caution: High voltage, electric shock) C9002 0.01uF 250V 1N4007 D9001 D9002 1N4007 D9003 1N4007 After secondary rectifications LF902 1N4007 D9004 LF-4ZB-E273H 1N4007 D9005 D9006 1N4007 R9002 R9003...
Page 101
Audio Check PATH Refer to troubleshooting "4.1. AUDIO CHECK"(93 page). HDMI CHECK6 TRANSMITTER ADV8002 CHECK5 with scaler video encoder etc... ADV7844 FRONT TMDS BUFFER AD8195 CHECK4 EPM240T100CN5 CHECK2 SPDIF/I2S SELECTOR SPDIF LC89058W-E DIGITAL AUDIO INTERFACE RECEIVER CHECK3 CHECK1 R2A15220FP...
LAEVEL DIAGRAM LEVEL DIAGRAM FRONT ch R2A15220FP ANALOG H/POUT SPEAKER LINE IN + GAIN ADJ. + MIC IN + AK5358B + + AK4358VQ - - AZ4580 MAX.OUTPUT 7.78Vrms +30dB SP OUT R2A15220FP MAX.OUTPUT 3.8Vrms AK4358VQ 4.24Vrms/8Ω DIFF.OUT AK5358B 0dBFS=5Vpp =1.77Vrms FULL SCALE LEVEL=2Vrms +20dB SINGLE INPUT...
Page 108
R2A15220FP LEVEL DIAGRAM SB-ch FRONT/ZONE ASIGN 0dB ZONE2/3 from F-ch from SPEAKER DA SB-ch + LINE IN + MAIN from EXT.IN SB-ch ZONE2 NJW1194 TONE MONO MUTE PREOUT MONO ZONE3 NJW1194 TONE MONO MUTE PREOUT MONO +30dB SP OUT 4.48Vrms/8Ω 0dBFS AK4424ET 2.0Vrms...
SMPS (COMPONENT SIDE) 2.2 X 1.2 C M D 1A 629 2.2 X 1.2 BK 903 5600uF/ 6. 3V 5600uF/ 6. 3V I C 903 1.2 X 3.1 C 9023 C 9021 D 9012 R 9019 SMPS B'D ADJ 1 ADJ 2 R 9018 R Y 901...
SPK_PREOUT (COMPONENT SIDE) JW 703B (33/23/6006) B K 701 C 7872 C 7813 JK 683 JK 682 JK 681 JK 684 JW 701A ( S R 6006) C 7871 C 7873 C 6805 C 7853 C 7863 C 7843 JK 781 JK 782 C 7833 C 7803...
SPK_PREOUT (FOIL SIDE) C 6877 C 7825 C 6745 C 6782 C 6820 C 7826 C 7815 C 7845 C 7835 C 7865 C 7878 C 7875 C 7805 C 7827 C 7855 C 7836 C 7866 C 7876 C 7816 C 7806 C 7846 C 7856...
INPUT (COMPONENT SIDE) 7.1CH IN IPOD SAT /CBL SL/SR C/SUB PH ON O AU X2 SBL / S BR JK 464 JK 462 JK 461 JK 465 C4647 C4648 C4643 C4644 C4637 C4638 C4633 C4634 C4627 C4628 JK 463 C4623 C4624 C4617 C4618...
INPUT (FOIL SIDE) R4692 R4609 R4620 R4630 R4691 R4640 C4649 R4610 R4619 R4629 R4639 R4649 C4609 C4619 C4629 C4639 R4650 C N 45B R4665 R4666 RE C_ L R4757 R4751 1. R E C _L 2. A G N D C4666 3.
FUSE (COMPONENT SIDE) FUSE (FOIL SIDE) POSISTOR (COMPONENT SIDE) POSISTOR (FOIL SIDE) C UP 12388-2 Z : T3.15A L/ 250V C N 932 F9302 R 9312 R 9316 : T3.15A L/ 250V R 9313 F9304 : T3.15A L/ 250V F9303 C N 941 C N 940 R 9315...
FRONT (COMPONENT SIDE) V.AUX (COMPONENT SIDE) CUP12383-2 LUG 61 F6001 C N69A D 6030 F 6001 T100m A L250V D 6019 D 6018 C N605 BK 601 FL601 V R602 V R601 DG ND C 6029 C 6091 A C 37V C 6032 C 6031 5.V A UX V...
HDMI FFC (COMPONENT SIDE) HDMI FFC (FOIL SIDE) USB (COMPONENT SIDE) USB (FOIL SIDE) C U P 12383-3 C 6109 R 6013 R 6110 BK 606 BK 607 L6004 R 6109 C 6067 R 6012 B N605 C 6068 V BUS V BUS BK 602 USBD+...
RS232C (COMPONENT SIDE) RS232C (FOIL SIDE) D 9902 D 9901 C 9908 C 9909 JK 9 9 1 C 9901 C 9903 C 9902 D 9903 D 9904 C 9905 C 9917 C 9921 C 9906 Pb Pb Pb Pb Pb Pb Pb Pb Pb Pb Pb Pb Pb Pb Pb Pb Pb Pb Pb Pb Pb Pb Pb Pb Pb Pb Pb Pb Pb Pb Pb Pb C N 99B C 9920 C 9916...
SIDE_CNT (COMPONENT SIDE) SIDE_CNT (FOIL SIDE) C N98B C N 97B C N 28A C N 27A C 9617 C 9618 R9608 C 9610 C 9611 C 9616 C 9612 C 9609 R9607 R 9646 C 9645 C 9615 C 9605 R9645 C N 961 C 9601...
VIDEO (COMPONENT SIDE) JK 554 1.DIN_SA T_Y 2.V G N D 3.DIN_SA T_CB C 5106 C 5108 C 5102 C 5104 4.V G N D 5.DIN_SA T_CR 1.M O N_CO M P _Y_O UT 6.V G N D 2.V G N D 7.SA T_LIN E1 3.M O N_CO M P _CB_O UT 8.SA T_LIN E2...
OPTION B R6925 AREA OPTION A OPEN OPEN OPTION B OPEN OPTION C OPEN OPEN C6923 R6921 L6752 75J-207CX 4700P(M) 1.2K CLM4B001Z C6921 8200P(M) R6927 C6931 R6923 10/50V TU_+9V 100K R6929 A+8V OPEN Q6929 AGND OPEN A-8V C6909 OPEN TRG_GND C6910 OPEN TRG_+15V...
SIDE CNT_CUP12387Z TO M-X PORT TO M-X PORT (PAGE 7/29) (PAGE 7/29) CN98B CN97B C125Z2-11 C125Z2-15 SR6006/U1B ONLY IC961 PQ033DNA1ZPH C9602 R9601 Specific IC 10/50V C9615 R9607 10/50V C9603 R9602 10/50V C9609 TO HD RADIO AUDIO_R AUDIO_M C9610 AUDIO_L C9604 R9603 TU 3.3V...
TO CONNECT B PART TO CONNECT A PART TO CONNECT B PART (PAEG 9/29) (PAEG 8/29) (PAEG 9/29) CN42B CN41B CN43B C125Z2 C125Z2 C125Z2 Trans. Temp_detect Part C4680 C4682 R4773 100K 0.022u 6800P R4774 100K R4765 C4676 R4761 R4680 R4682 R4662 10/50 D2399...
PAGE18/29 PAGE14/29 TO LEVEL CHG. TO DIGITAL CONT. N1B(EUR) Q2010 THER PROT C OPEN R2124 R2125 R2130 OPEN OPEN R2042 open R2055 open R2040 4.7K R2073 R2041 4.7K open R2109 4.7K Q2011 IPOD R2045 4.7K OPEN R2046 4.7K R2047 4.7K R2128 R2129 R2134...
PAGE14/29 TO DIGITAL CONNECT PAGE15/29 DIGITAL SUPPLY 232C VIDEO.OUT DETECT R2402 4.7K DGND SR6006 N Verion ONLY 232IMO3 VIDEO.IN (RDS) 232OMI3 Q2409 Q2413 OPEN OPEN T186 T185 T187 Q2410 Q2412 OPEN OPEN Q2403 Q2406 Q2401 2SC3052 2SC3052 RT1N141C Q2407 Q2408 Q2411 Q2414 Q2402...
PAGE 20/29 PAGE 20/29 PAGE 20/29 FROM PLD PART TO PLD PART FROM PLD PART PAGE 17/29 FROM SCPU PART DSP_CONT TP42 TP41 R4153 OPEN R4152 DSP_FLAG0 R4159 C4161 R4151 IC409 1000P W9864G6JH-6 C4097 R4099 C4106 VDD_INT DAI_P09 FLAG0 DAI_P05 R4098 C4107 DQ15...
PAGE 20/29 PAGE 17/29 TO SUB CPU TO AUDIO PLD R4517 open open R4518 DA+5V R4195 DA-8V R4187 R4183 OPEN OPEN DA+8V D_AUDIO C4193 R4191 R4189 C4181 R4185 OPEN OPEN OPEN OPEN ADINL OPEN ADINR R4193 OPEN R4194 DAGND OPEN C4194 R4192 R4188...
EXPLODED VIEW S12 x4 U1B only C12 z S5 x21 N1SG only S1 x8 WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacturer. 印の部分は安全を維持するために重要 な部品です。従って交換時は必ず指定の 部品を使用してください。...
PARTS LIST OF EXPLODED VIEW z Parts indicated by "nsp" on this table cannot be supplied. z P.W.B. ASS'Y indicated by "nsp" on this table cannot be supplied. When repairing the P.W.B. ASS'Y, check the board parts list and order replacement parts. z Parts indicated by the "...
PACKING VIEW PARTS LIST OF PACKING & ACCESSORIES z Parts indicated by "nsp" on this table cannot be supplied. z Parts indicated by the " ★ " mark are not illustrated in the exploded view. z The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions. Ref.
Page 162
Ref. No. Part No. Part Name Remarks Q'ty INSTRUCTION MANUAL ASS'Y 6-1 35201004612AM MANUAL, CD ASS'Y CFT1A037YA 6-1 35201004613AM MANUAL, CD ASS'Y N1B,N1SG CFT1A038YA 6-1 352010046056M MANUAL, CD ASS'Y CFT1A039ZA WARRANTY, USA CQE1A131W WARRANTY, CANADA CQE1A132V 6-4 542110066029M MANUAL, GUIDE CQX1A1600Z 6-4 542110066036M MANUAL, GUIDE N1B,N1SG...
SEMICONDUCTORS Only major semiconductors are shown. General semiconductors etc. are omitted from list. The semiconductors which have a detailed drawing in a schematic diagram are omitted from list. 1. IC's R5F5630ECDFB (DIGITAL : IC201) RX630 Group PLQP0144KA-A (144pin LQFP) (Top) R5F5630ECDFB Terminal Functions Pin Name Synbol...
Page 164
Pin Name Synbol Tolerant I/O Pu/Pd LvCnv STBY stop Function 24 P35(input only)/NMI NC TRST#-A/P34/ IRQ4-C/SCK6-A/ TRST# ○ E20 Emulator control signal/Usual:"Hi-z" SCK0-B P33/TIOCD0-B/ RXD6-A/RXD0-B/ PLDAERR ○ O/L PLD ERROR detection(Output of A PLD) IRQ3-DS P32/TIOCC0/ TXD6-A/TXD0-B/ FLASHER IN ○ O/L/I O/L/I FLASHER input control pin (TIMER) IRQ2-DS TMS-A/P31/...
Page 165
Pin Name Synbol Tolerant I/O Pu/Pd LvCnv STBY stop Function 58 TRCLK-A/P83 ADV8002 SPI CS O/L GUI control pin(ADV8002) 59 VCC Power supply pin PC7/TIOCB6/TXD8/ GUI control pin(ADV8002)/ MITSUBISHI writer rewrite:"L"(from ADV8002 SPI MO/PC7 ○ IRQ14-B external) PC6/TIOCA6/RXD8/ ADV8002 SPI MI ○...
Page 166
Pin Name Synbol Tolerant I/O Pu/Pd LvCnv STBY stop Function PE6/TIOCA11/ PRE Z3 MUTE O/L PRE OUT MUTE control IRQ6-C/AN4 103 PK5/TXD4-B O/L NC 104 P70/SCK4-B O/L NC 105 PK4/RXD4-B O/L NC PE5/TIOCB10/ O/L NC IRQ5-C/AN3 107 PE4/TIOCA10/AN2 VOL CLK O/L FUNCTION/VOLUME control(R2A15220) 108 PE3/TIOCB9/AN1 VOL DATA...
Page 168
R5F3650KNFB Terminal Functions Pu/Pd Pin Name Synbol I/O Type P.OFF Function (Ext.) STBY 1 P94 2 P93 DIR CE DIR control pin (LC89058W-VF4A) 3 P92/SOUT3 DIR DIN DIR control pin (LC89058W-VF4A) 4 P91/SIN3 DIR DOUT DA3.3Pu DIR control pin (LC89058W-VF4A) 5 P90/CLK3 DIR CLK DIR control pin (LC89058W-VF4A)
Page 169
Pu/Pd Pin Name Synbol I/O Type P.OFF Function (Ext.) STBY 60 VCC +3.3V 61 P30 DAC MS DAC control pin(ASK4358) 62 VSS 63 P27 DAC RST DAC control pin(ASK4358) MODE1=O/H 64 P26 DV POWER DIGITAL VIDEO power control pin (DV5V,DV3.3V) MODE2=O/L 65 P25/INT7 ADV7844 INT1...
Page 173
LC89058W-E (HDMI : IC403,IC404,IC405) 35 34 33 32 31 30 29 28 27 26 25 SDIN SLRCK SBCK RDATA XMODE RLRCK LC89058W-E DV DD DGND DGND DV DD RBCK GPIO0 GPIO1 RMCK GPIO2 AGND GPIO3 AV DD RXOUT2 * : Pull-down resistor internal at no selection Pin Functions RXOUT1 RX0-6 input S/PDIF through output pin 1...
Page 174
LC89058W-E Continued from preceding page. Pin No. Name Function DGND Digital GND DV DD Digital power supply (3.3V) XMCK Oscillation amplifier clock output pin XOUT Output pin connected to the resonator External clock input pin, connected to the resonator (12.288MHz/24.576MHz) DV DD Digital power supply DGND...
Page 175
ADSP21487KSWZ-4B (HDMI : IC408) PIN 1 Preliminary Technical Data ADSP-21483/21486/21487/21488/21489 TOP VIEW (PINS DOWN) 176-LEAD LQFP_EP LEAD ASSIGNMENT ADSP21487KSWZ Terminal Function Table 53. 176-Lead LQFP_EP Lead Assignment Pin Name Pin No. Pin Name Pin No. Pin Name Pin No. Pin Name Pin No.
Page 177
W9864G6JH-6 Block diagram CLOCK BUFFER CONTROL SIGNAL GENERATOR COMMAND DECODER COLUMN DECODER COLUMN DECODER CELL ARRAY CELL ARRAY BANK #0 BANK #1 MODE REGISTER SENSE AMPLIFIER SENSE AMPLIFIER ADDRESS BUFFER DATA CONTROL CIRCUIT BUFFER DQ31 COLUMN REFRESH COUNTER COUNTER DQM0~3 COLUMN DECODER COLUMN DECODER CELL ARRAY...
Page 178
W9864G2IH W9864G6JH-6 Pin description 5. PIN DESCRIPTION PIN NUMBER PIN NAME FUNCTION DESCRIPTION Multiplexed pins for row and column address. Row address: A0−A10. Column address: A0−A7. 24, 25, 26, 27, 60, 61, 62, A0−A10 Address A10 is sampled during a precharge command to 63, 64, 65, 66 determine if all banks are to be precharged or bank selected by BS0, BS1.
Page 183
DSDL4 DAC4 DSD Lch Data Input Pin DSDR4 DAC4 DSD Rch Data Input Pin DSDL1 DAC1 DSD Lch Data Input Pin DSDR1 DAC1 DSD Rch Data Input Pin DSDL2 DAC2DSD Lch Data Input Pin DSDR2 DAC2 DSD Rch Data Input Pin H27U1G8F2B Series DSDL3 DAC3 DSD Lch Data Input Pin...
Page 184
1.2 PIN DESCRIPTION H27U1G8F2BTR-BC Pin Function Pin Name Description DATA INPUTS/OUTPUTS The IO pins allow to input command, address and data and to output data during read / program IO0 ~ IO7 operations. The inputs are latched on the rising edge of Write Enable (WE). The I/O buffer float to High-Z when the device is deselected or the outputs are disabled.
Page 187
±15kV ESD Protected MII/RMII Fast-Ethernet PHY with HP Auto-MDIX and SMSC flexPWR in a Small Footprint Datasheet LAN8700 Pin Description Table 2.1 LAN8700/LAN8700I 36-PIN QFN Pinout PIN NO. PIN NAME PIN NO. PIN NAME nINT/TX_ER/TXD4 RX_DV RX_CLK/REGOFF CRS/PHYAD4 RX_ER/RXD4 MDIO TXCLK nRST TXD0...
Page 188
SAA7121 (HDMI : IC323) 33 V SSA2 res. V SSA1 V DDA3 CVBS V SSD1 res. SAA7120 V DDD1 V DDA2 SAA7121 RCV1 res. RCV2 V DDA1 res. MBH790 SAA7121 Block Diagram V DDA1, handbook, full pagewidth RCV1 TTXRQ XTALO V DDA2 , V DDA4 V DDA3...
Page 189
Digital Video Encoder (ConDENC) SAA7120; SAA7121 SAA7121 Pin Description PINNING SYMBOL DESCRIPTION − res. reserved test pin; connected to digital ground for normal operation test pin; connected to digital ground for normal operation line-locked clock; this is the 27 MHz master clock for the encoder digital ground 1 SSD1 digital supply voltage 1...
Page 190
CONFIDENTIAL 8-CHANNEL ELECTRONIC VOLUME With 14-Input selector And Tone control BLOCK DIAGRAM AND PIN CONFIGURATION (TOP VIEW) R2A15220FP (AUDIO : IC471) TRER MUTE AVEE AVCC BASSR2 AVEE BASSR1 ADCL 0/-6/-12/-18dB ADCR TREL SUB2 AGND BASSL2 MAIN INR1 BASSL1 Bass/ Treble 0~-95dB, +42~0dB -14~+14dB...
Page 191
R2A15220FP R2A15220FP CONFIDENTIAL 8-CHANNEL ELECTRONIC VOLUME With 14-Input selector And Tone control PIN DESCRIPTION R2A15220FP Pin Function PIN No. Function Name FROUT,FLOUT, 22,20, COUT,SWOUT, 16,14, Output pin of FL/FR/C/SW/SL/SR/SBL/SBR channel SROUT, SLOUT, 10, 8, SBROUT,SBLOUT 2, 100 23,19, FR Pre-out,FL Pre-out, Pre-output pin of FL/FR/SL/SR/SBL/SBR channel 11, 7, SR Pre-out, SL Pre-out,...
Page 192
G G I I I I BLOCK DIAGRAM NJW1194A (AUDIO : IC484,IC489) ...
PARTS LIST OF P.C.B. UNIT z Parts indicated by "nsp" on this table cannot be supplied. z The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions. PCB FRONT ASSY Ref.
Page 195
Ref. No. Part No. Part Name Remarks Q'ty C6047 CAP, CHIP(1608, 50V/82pF) CCUS1H820JA C6048 00D9430062101 ELECT CAP 100UF 16V CCEA1CH101T C6051,6052 CHIP CAP 0.1UF 50V K CCUS1H104KC C6057,6058 00D9430175108 ELECT CAP 10UF 50V CCEA1HH100T C6059,6060 CHIP CAP 330PF 50V J CCUS1H331JA C6061,6062 CHIP CAP 0.1UF 50V K...
Need help?
Do you have a question about the SR6006/U1B and is the answer not in the manual?
Questions and answers