Related Manuals for Well Straler T4
Summary of Contents for Well Straler T4
- Page 1 User Guide MODULATING version T4 (230 V) WELL STRALER Hertstraat B-9473 Welle (0)53 (0)53 info@wellstraler.be...
-
Page 2: Table Of Contents
Index Introduction ................................3 1.1. Welcome ................................. 3 1.2. Warranty ................................. 3 1.3. Security ................................... 3 1.3.1. Built-in safeties in the control system ........................3 1.3.2. Communication safety - transmitter ........................3 1.3.3. Safety for temperature sensor of transmitter……………………………………………………………………………………………………4 1.3.4. Safety for temperature sensor of receiver………………………………………………………………………………………………………….4 1.3.5. -
Page 3: Introduction
1.1. Welcome Thank you for buying your Well Straler gas heater! We are glad to have you as a customer. With this quality product you will enjoy the cozy warmth and unique flame dance for many years. Before using the heater, please read the instructions carefully and keep them in a safe place. -
Page 4: Safety For Temperature Sensor Of Transmitter
1.3.3. Safety for temperature sensor of transmitter By defect of the temperature sensor of the transmitter, the red led will also start blinking (0.5 second on, 0,5 second off) and the system will switch to the temperature sensor of the receiver. All other functions of the transmitter will continue to function normally. -
Page 5: Commands Of Your Appliance
2. Commands of your appliance Some advantages of the Well Straler new product generation: Automatic ignition without steady pilot; Precise digital temperature control in a range of ± 6 m from the heater; Wireless RF remote control of all the functions of your heater in a range of ±... -
Page 6: Initial Set-Up Programming Of Transmitter
FLAME- FLAME+ MODE MODE AUTO FLAME- FLAME+ MODE REVIEW RESET RETURN MODE AUTO FLAME- FLAME+ AHEAD TIMER BACK REVIEW MODE RETURN RESET 2.3. Initial set-up programming of transmitter MODE AUTO AHEAD TIMER BACK REVIEW RETURN RESET Follow the procedure below before first use: To program settings, remove the battery cover on the back of the trans- AHEAD TIMER... -
Page 7: Setting Of Swing
2.3.4 Setting SWING 1. Press AHEAD and BACK buttons together. De actual set SWING (difference in temperature between on and off mode of thermostat) will appear in the SET TEMP window, together with the mention SWING on the display. 2. Press UP/DOWN to change the SWING. 3. - Page 8 FLAME- FLAME+ FLAME- FLAME+ MODE MODE FLAME- FLAME+ MODE AUTO MODE AUTO FLAME- FLAME+ MODE MODE AUTO REVIEW RESET MODE RETURN REVIEW RESET RETURN MODE AUTO To make changes in the standard program: REVIEW RETURN AHEAD RESET AHEAD TIMER BACK TIMER BACK 1.
-
Page 9: Program Overview
FLAME- FLAME+ FLAME- FLAME+ MODE MODE MODE AUTO MODE AUTO REVIEW RETURN RESET REVIEW RESET RETURN 2.4.2. Program overview AHEAD TIMER BACK AHEAD TIMER BACK If you want to review the settings for either the factory program and/or your customized program, you may do so by (in OFF-mode) FLAME- FLAME+... -
Page 10: Thermo Operation (On/Off Based On Set Temp Setting)
2.5.2. Thermo operation (ON/OFF BASED ON SET TEMP SETTING) FLAME- FLAME+ MODE The system can control your appliance thermostatically when operating in THERMO mode. MODE AUTO 1. Starting in OFF mode, press MODE until the REVIEW RESET RETURN LCD-screen displays THERMO. 2. -
Page 11: Adjusting Fan Speed
FLAME- FLAME+ MODE MODE AUTO FLAME- FLAME+ REVIEW RETURN FLAME- RESET FLAME+ MODE MODE MODE AUTO FLAME- FLAME+ AHEAD TIMER BACK MODE AUTO 2.5.5. Adjusting FAN speed* MODE REVIEW RETURN RESET MODE AUTO REVIEW RETURN RESET The speed of the FAN can be adjusted only in the following modes: ON - THERMO – PROGRAM. AHEAD TIMER BACK... -
Page 12: Setting The Countdown Timer
AHEAD TIMER BACK FLAME- FLAME+ MODE 2.5.8. Setting the countdown timer MODE AUTO REVIEW RETURN RESET This system can operate with a built-in COUNTDOWN timer when the transmitter is in the ON or THERMO mode (THERMO or ON must be displayed on the LCD-screen). AHEAD TIMER BACK... -
Page 13: Receiver
2.6 Receiver The receiver is built-in in your appliance and has a 3-position slide button: LEFT: REMOTE (the system only operates if the receiver receives commands from the transmitter) MIDDLE: ON (the system operates manually by using the buttons on the receiver) ... -
Page 14: Connecting The Receiver
2.6.3. Connecting the receiver Connection Wire harness 230V connection EXTREMELY IMPORTANT: MAKE SURE THE WIRES ARE CONNECTED IN THE RIGHT WAY!! -
Page 15: Fixation Of The Sensor Of Thermostat
2.6.4 Fixation of sensor of thermostat The receiver is equipped with an extra thermostatic sensor that will be activated if the signal of the transmitter disappears. This sensor is self adhesive and can be stuck on any smooth surface. Take care that the sensor is installed where normal air convection is possible. -
Page 16: Reset By Failure
PROBLEM CAUSE SOLUTION A red led is blinking on the The temperature sensor in the Replace transmitter receiver (0,5 sec. On/0,5 transmitter is out of service. sec. Off) A red led is blinking on the The transmitter is positioned out The fire will continue to work.
Need help?
Do you have a question about the T4 and is the answer not in the manual?
Questions and answers