EK-Quantum Vector2 FE RTX 4090 D-RGB User Manual
  1. Manuals
  2. Brands
  3. EK-Quantum Manuals
  4. Computer Hardware
  5. Vector2 Strix RTX 3080 D-RGB
  6. User manual

EK-Quantum Vector2 FE RTX 4090 D-RGB User Manual

Gpu water block
Hide thumbs Also See for Vector2 FE RTX 4090 D-RGB:
Table of Contents

Advertisement

Quick Links

Download this manual
EK-Quantum
Vector² FE RTX 4090 D-RGB
GPU WATER BLOCK
USER GUIDE

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Vector2 FE RTX 4090 D-RGB and is the answer not in the manual?

Questions and answers

Related Manuals for EK-Quantum Vector2 FE RTX 4090 D-RGB

Summary of Contents for EK-Quantum Vector2 FE RTX 4090 D-RGB

  • Page 1 EK-Quantum Vector² FE RTX 4090 D-RGB GPU WATER BLOCK USER GUIDE...
  • Page 2 Please note the installation of the product is intended to be undertaken by an adequately trained and experienced person. You are installing the product at your own risk. If you are not properly trained or experienced or feel unsure about the installation procedure, please refrain from installing the product yourself and contact our tech support for assistance.

  • Page 3: Table Of Contents

    TABLE OF CONTENTS BOX CONTENTS WATER BLOCK DIMENSIONS TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS NICKEL PLEXI NICKEL ACETAL PREPARING THE GRAPHICS CARD REMOVING THE STOCK COOLER PREPARING THE WATER BLOCK FOR INSTALLATION CUTTING AND PLACING THERMAL PADS APPLYING THERMAL COMPOUND ATTACHING THE WATER BLOCK INSTALLING THE BACKPLATE ATTACHING THE BACKPLATE...

  • Page 4: Box Contents

    BOX CONTENTS EAN: 105871 M2.5x4 AX1 Screw (7 pcs) M2.5x8 AX1 Screw (1 pc) Standoff Ø4.5/2.5 (1 pc) EK-Quantum Vector FE RTX 4090 D-RGB M3x10 AX1 Screw (1 pc) Polyamid Washer M2.5 0.5mm (7 pcs) Standoff M2.5-M3 x 6.6mm (1 pc) Thermal Pad F 1.0 mm (6 pcs)

  • Page 5: Water Block Dimensions

    WATER BLOCK DIMENSIONS 236.3 mm 123.9 mm 27 mm 95.9 mm 25.7 mm - 5 -...

  • Page 6: Technical Specifications And Water Block Parts

    TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS NICKEL PLEXI - Dimensions: (L x H x W): 236.3 x 148 x 27 mm - D-RGB LED count: 14 - D-RGB cable length: 50 cm - D-RGB connector 3-pin 5V digital LED header Position Description Quantity...

  • Page 7: Nickel Acetal

    NICKEL ACETAL - Dimensions: (L x H x W): 236.3 x 148 x 27 mm - D-RGB LED count: 28 - D-RGB cable length: 50 cm - D-RGB connector 3-pin 5V digital LED header Position Description Quantity 105849 Coldplate (Nickel) 100663 EK - Badge 103947...

  • Page 8: Preparing The Graphics Card

    Place your graphics card on the flat surface and carefully remove the stock cooler. Do not forget to unplug all the LED and fan connectors. Pay attention to the following steps when installing the EK-Quantum Vector FE RTX 4090 water block onto your graphics card.

  • Page 9: Cutting And Placing Thermal Pads

    CUTTING AND PLACING THERMAL PADS STEP 1 Thermal Pad F – 1.0 mm (120 x 16 mm) The GPU water block comes with thermal pads that have to be cut into smaller pieces to cover all the VRM components, such as COILs, MOSFETs, and drivers.

  • Page 10: Applying Thermal Compound

    APPLYING THERMAL COMPOUND STEP 1 Apply the enclosed thermal grease (thermal compound) on the GPU heat spreader – IHS – as shown in the image. The layer of the thermal compound must be thin and even over the entire surface of the IHS.
  • Page 11 STEP 2 M2.5 x 4 AX1 SCREW Use five (5) M2.5 x 4 AX1 Screws and PVC washers to tighten the PCB on the water block. Tighten the screws evenly using the M2.5 PVC Phillips-head screwdriver. EK recommends you start tightening the WASHER screws around the GPU core first, and then continuing outward to prevent damage to the GPU.

  • Page 12: Installing The Backplate

    INSTALLING THE BACKPLATE STEP 1 Thermal Pad F – 1.0 mm (120 x 16 mm) After attaching the water block, a few more thermal pads need to be cut into smaller pieces to cover all the necessary components. EK made sure to provide you with more than an adequate quantity of 1 mm 120 mm thermal pads to complete this step.

  • Page 13: Attaching The Backplate

    ATTACHING THE BACKPLATE STEP 1 Position the I/O Bracket and backplate (including screws and BACKPLATE standoffs) onto the GPU PCB. Make sure all the holes are aligned. Tighten the screws evenly. Before attaching the backplate, make sure all the Thermal Pads are placed correctly! Do not use excessive force! For this step, you will need:...

  • Page 14: Connecting The D-Rgb Led Strip

    CONNECTING THE D-RGB LED STRIP STEP 1 Plug the 3-pin connector of the distribution plate D-RGB LED light to the D-RGB HEADER on the motherboard. The LED will work if the pin layout on the header is as follows: +5V, Digital, Empty, Ground.

  • Page 15: Warranty

    WARRANTY Our products are warranted against defects of materials and quality for a period of 24 months, starting with the date of delivery to the end-user. During this period, products will be repaired or have parts replaced at our discretion, provided that 1) the product is returned to the agent from whom it was purchased;...

  • Page 16: Support And Service

    SUPPORT AND SERVICE In case you need assistance or wish to order spare parts or a new mounting mechanism, please contact: https://www.ekwb.com/customer-support/ For spare parts orders, refer to the page with “TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS” where you can find the EAN number of each part you might need.

Table of Contents