Woodland Mills HM126 Operator's Manual
  1. Manuals
  2. Brands
  3. Woodland Mills Manuals
  4. Industrial Equipment
  5. HM126
  6. Operator's manual

Woodland Mills HM126 Operator's Manual

Lap siding attachment
Hide thumbs Also See for HM126:
Table of Contents

Advertisement

Quick Links

Download this manual
SAWMILL ACCESSORY


LAP SIDING ATTACHMENT
OPERATOR'S MANUAL
Lap siding attachment is compatible with HM130, HM130MAX, and select HM122 & HM126 sawmills.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HM126 and is the answer not in the manual?

Questions and answers

Related Manuals for Woodland Mills HM126

Summary of Contents for Woodland Mills HM126

  • Page 1 SAWMILL ACCESSORY 
 LAP SIDING ATTACHMENT OPERATOR’S MANUAL Lap siding attachment is compatible with HM130, HM130MAX, and select HM122 & HM126 sawmills.
  • Page 2 
 This page intentionally left blank.

  • Page 3: Table Of Contents

    REAR IDLER ______________________________________________________22 TUNING BLOCK ___________________________________________________22 INSTALLATION ____________________________________________________23 6. CARRIAGE WHEEL ARMS _________________________________________30 7. INDEXING HANDLE SPACER ______________________________________32 HM126, HM130 & HM130MAX INSTALLATION ONLY ___________________32 HM122 INSTALLATION ONLY ________________________________________33 8. CABLE CHAIN___________________________________________________34 CARRIAGE WHEEL ADJUSTMENT ___________________________________40 0003389-M-EN: Rev B Page...
  • Page 4 EXPLODED ASSEMBLY VIEWS __________________________________________64 CARRIAGE WHEEL ARM _____________________________________________64 WHEEL SWEEPER __________________________________________________65 CHAIN ADJUSTMENT BRACKET_______________________________________66 REAR IDLER [HM122] _______________________________________________67 REAR IDLER [HM126 & HM130(MAX)] __________________________________68 INDEXING HANDLE & LEVER _________________________________________69 TRACK RAIL EXTENSION, TRAVEL HOOKS, CABLE CHAIN ________________70 PARTS LIST __________________________________________________________71 NOTES ______________________________________________________________73...

  • Page 5: Technical Specifications

    Sawmill Model Model Years Lap Siding Compatible? 2019 & Earlier HM122 2020 & Newer 2016 & Earlier HM126 2017 & Newer 2016 & Earlier HM130 2017—2019 HM130MAX 2020 & Newer The lap siding attachment is also compatible with the sawmills listed above in combination with...

  • Page 6: Component Lists

    Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual COMPONENT LISTS Verify all component and hardware quantities are correct prior to assembling the Lap Siding Attachment (LSA). COMMON LSA COMPONENTS Setup Block Wheel Sweeper [0002913] Assembly Chain Indexing Adjustment Handle Bracket [0002823] Assembly Extension...

  • Page 7: Hm122-Specific Lsa Components

    600 N [134.9 lbf] [0002856] [0003885] Travel Hook Rear Idler with Lanyard Assembly [0003724] Cable Chain [0005210] HM126- & HM130-SPECIFIC LSA COMPONENTS Chain Lever Gas Spring Plate 950 N [213.5 lbf] [0002830] [0003886] Travel Hook Rear Idler with Lanyard Assembly...

  • Page 8: To-Scale Hardware

    Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual TO-SCALE HARDWARE BOLTS & SCREWS Hardware graphics are printed at 1:1 scale for ease of identification. Simply place the hardware over the image in the tables to verify it is the correct size. HHB-MBM075FCJ M10 X 1.5 X 20 mm HEX BOLT HHB-MBM090FCJ...
  • Page 9 Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual HHB-MBR145FCJ M12 X 1.75 X 90 mm HEX BOLT HHB-MCF145PCJ M20 X 2.5 X 90 mm HEX BOLT FHH-MBM080FCM* M10 X 1.5 X 25 mm FLANGED HEX BOLT FHH-MBM085FCM M10 X 1.5 X 30 mm FLANGED HEX BOLT FHH-MBM155PCM M10 X 1.5 X 100 mm FLANGED HEX BOLT * M10 X 1.5 X 25 mm Flanged Hex Bolts are only applicable on Lap Siding Attachment...

  • Page 10: Washers

    Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual SHC-MBR165PCP M12 X 1.75 X 110 mm SOCKET HEAD CAP SCREW SCALES Ruler scales are also provided below to double-check bolt and screw lengths when necessary. WASHERS FTW-MBM000AJ FTW-MBR000AJ M10 FLAT WASHER M12 FLAT WASHER FTW-MCF000AJ M20 FLAT WASHER...

  • Page 11: Nuts

    Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual NUTS HXN-MBMCH HXN-MBRCH M10 X 1.5 HEX NUT M12 X 1.75 HEX NUT THN-MBMCC HLN-MBMCH M10 X 1.5 THIN HEX NUT M10 X 1.5 LOCK NUT HLN-MBRCH HLN-MCFCH M12 X 1.75 LOCK NUT M20 X 2.5 LOCK NUT FLN-MBMCH** M10 X 1.5 FLANGED LOCK NUT...

  • Page 12: Assembly

    Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual ASSEMBLY 1. TOOLS REQUIRED Tool Specification Wrench/Socket 8 mm Wrench/Socket 9 mm Wrench/Socket 10 mm Wrench/Socket 13 mm Wrench/Socket 14 mm Wrench/Socket 15 mm Wrench/Socket 16 mm Wrench/Socket 17 mm Wrench/Socket 18 mm Wrench/Socket 19 mm Hex Key...

  • Page 13: Setup Blocks

    Setup Block Hex Bolt For the HM126, HM130, or HM130MAX; roll the sawmill carriage until the rear carriage wheel is just behind the pair of track holes and the front carriage wheel is past the quad set of track holes.
  • Page 14 Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual For HM122 sawmills, roll the carriage until the front carriage post is centred on of the track rail seams. The setup blocks for the HM122 will be installed on the outer two holes of the 4 hole pattern at the seam.
  • Page 15 Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual Assemble the two (2) setup blocks to the outer face of the track rail using two (2) M10 X 25 mm hex bolts through the holes shown below. Assemble setup blocks to these holes With the setup blocks in place, the inner carriage plate will support the weight of the sawmill carriage once the carriage wheels are removed.

  • Page 16: Sawmill Disassembly

    Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual 3. SAWMILL DISASSEMBLY Some components and hardware must be removed from the sawmill before the lap siding attachment can be assembled. Be sure to store and label all these components and their associated hardware in case the lap siding attachment is removed in the future.

  • Page 17: Carriage Wheels And Spacers

    Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual CARRIAGE WHEELS AND SPACERS Remove the two (2) carriage wheel assemblies, four (4) spacers*, two (2) M20 X 120 mm hex bolts, eight (8) M20 flat washers, and two (2) M20 lock nuts from the right-side carriage leg. *Note: on pre-2020 model sawmills, there may be only one (1) spacer per carriage wheel.

  • Page 18: Carriage Post Lower Bolts

    Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual CARRIAGE POST LOWER BOLTS Remove the two (2) M12 X 80 mm hex bolts, four (4) M12 flat washers, and two (2) M12 lock nuts from the bottom of each right-side carriage post. **Some components removed for clarity** Set one (1) M12 X 80 mm hex bolt, two (2) M12 flat washers, and one (1) M12 lock nut aside to be reused on Step 4, CHAIN ADJUSTMENT BRACKET.

  • Page 19: Push Handle Bolt

    Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual PUSH HANDLE BOLT **Ignore this step if lap siding attachment is being installed on an HM122.** On 2020 model year sawmills, remove the upper M10 X 70 mm flanged hex bolt, M10 flat washer, and M10 lock nut from the push handle.

  • Page 20: Chain Adjustment Bracket

    Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual 4. CHAIN ADJUSTMENT BRACKET Using the hardware listed below, assemble the gas spring to the chain adjustment bracket. M10 X 65 mm M10 Hex Nut Hex Bolt M10 X 35 mm Gas Spring Hex Bolt Chain M10 Lock Nut...
  • Page 21 Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual Insert the chain adjustment bracket and gas spring sub-assembly between the carriage side plates from the bottom. Insert the front tabs of the bracket up inside the front carriage post and secure it with the M12 X 80 mm hex bolt, two (2) M12 flat washers, and one (1) M12 lock nut from Step 3, CARRIAGE POST LOWER BOLTS.

  • Page 22: Rear Idler, Lever Plates, & Chain Lever

    Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual 5. REAR IDLER, LEVER PLATES, & CHAIN LEVER Using the hardware listed below, assemble the rear idler, lever plates, and chain lever to the carriage leg. M12 X 100 mm Extension Hex Bolt Spring M10 X 90 mm Spacer...

  • Page 23: Lever Plates

    HM122 HM130 HM130MAX The lever plate for the HM126, HM130, and HM130MAX works with all three (3) sawmill models. Care must be taken to assemble the spacer to the proper hole in the lever plate depending on the model. Assemble spacer to...

  • Page 24: Rear Idler

    HM126 HM122 HM130 HM130MAX Top hole for HM126 sawmills. Bottom hole for HM130 and HM130MAX sawmills. TUNING BLOCK First, assemble the M10 X 65 mm hex bolt and M10 thin hex nut to the tuning block as shown below.

  • Page 25: Installation

    Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual INSTALLATION Slide the chain lever down between the carriage side plates. Tab and hole towards front of sawmill 0003389-M-EN: Rev B Page 10-Jun-2022...
  • Page 26 Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual Insert the two (2) bushings into the left and right side of the chain lever. 0003389-M-EN: Rev B Page 10-Jun-2022...
  • Page 27 Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual Insert one (1) M12 X 100 mm hex bolt through the bottom hole of the rear post with one (1) M12 flat washer and one (1) chain lever plate. Do not fully slide the bolt through the post. Insert the rear idler into the bottom of the post and fully slide the bolt through.
  • Page 28 Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual Next, slide the chain lever in between the two chain lever plates, aligning it with the pivot hole (as discussed in section, LEVER PLATES, on page 21). Secure it with one (1) M10 X 90 mm hex bolt, two (2) M10 flat washers, and one (1) M10 lock nut.
  • Page 29 Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual Next, position the spacer between the lever plates, aligning it with the appropriate holes in the plates (as discussed in section, LEVER PLATES, on page 21). Secure it with one (1) M10 X 90 mm hex bolt, two (2) M10 flat washers, and one (1) M10 lock nut.
  • Page 30 Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual Position the spacer and plates so that the spacer makes contact with the inner edge of the carriage side plate. Fully tighten the M10 X 90 mm hex bolt at the spacer then fully tighten the M12 X 100 mm hex bolt.
  • Page 31 Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual Finally, hook the extension spring onto the slot in the tuning block as shown below and allow the free end to simply hang down. 0003389-M-EN: Rev B Page 10-Jun-2022...

  • Page 32: Carriage Wheel Arms

    Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual 6. CARRIAGE WHEEL ARMS Using the hardware listed below, assemble the carriage wheel arms to the carriage leg. M20 X 90 mm Thrust Bearing Hex Bolt [51204] Carriage M20 Lock Nut Wheel Arm Sub-Assembly M20 Flat Washer...
  • Page 33 Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual Sawmill Carriage Side Plate Carriage Wheel Arm Assembly Ensure carriage wheel grooves are aligned with track rail before tightening hardware. Track Rail Setup Block 0003389-M-EN: Rev B Page 10-Jun-2022...

  • Page 34: Indexing Handle Spacer

    Bolt M10 Flanged Lock Nut HM126, HM130 & HM130MAX INSTALLATION ONLY Assemble the spacer to the push handle using one (1) M10 X 100 mm flanged hex bolt and one (1) M10 flanged lock nut. Fully tighten the hardware. M10 X 100 mm...

  • Page 35: Hm122 Installation Only

    Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual HM122 INSTALLATION ONLY Assemble the spacer to the rear carriage post beneath the push handle using one (1) M10 X 100 mm flanged hex bolt and one (1) M10 flanged lock nut. Fully tighten the hardware. M10 X 100 mm 0003389-M-EN: Rev B Page...

  • Page 36: Cable Chain

    Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual 8. CABLE CHAIN Route the cable chain and connect it to the lap siding linkage as outlined in the steps below. Cable Chain Push the chain lever all the way forward until it stops against the bolt in the tuning block. Ensure that the chain lever is parallel to the tuning block or less (towards the front of the sawmill).
  • Page 37 Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual Remove the master link from the open end of the cable chain. Starting from the back of the machine, route the chain between the carriage legs and over top of the rear idler sprocket. Connect the chain to the bottom of the chain lever with the master link as shown below.
  • Page 38 Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual The groove in the carriage wheel must be seated down on the track rail as far as it will go. Route the cable chain around the rear sprocket and then over top of the rear carriage wheel arm, ensuring all the slack is out of the chain while doing so.
  • Page 39 Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual Continue to route the chain under the lower sprocket and then around the outside of the front carriage wheel arm, ensuring as much slack is out of the chain as possible. Like the rear carriage wheel, the groove in the front carriage wheel must also be seated down on the track rail as far as it will go.
  • Page 40 Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual Route the remainder of the chain portion around the front side of the carriage wheel arm sprocket. Now route the cable portion of the cable chain under the chain adjustment bracket pulley and hook the open loop end on the extension spring.
  • Page 41 Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual 0003389-M-EN: Rev B Page 10-Jun-2022...

  • Page 42: Carriage Wheel Adjustment

    Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual CARRIAGE WHEEL ADJUSTMENT Push the chain lever back with just enough force so that the carriage wheels bind with the track rail. The carriage wheels should not be able to spin. Thread the tuning block bolt in until it stops at the chain lever. Do not tighten the jam nut as further adjustment to this bolt will be necessary.
  • Page 43 Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual If the front carriage wheel is not binding with the track rail, there is likely slack in the chain between the chain adjustment bracket sprocket and the front carriage wheel arm sprocket. Chain Adjustment Bracket Bolt Chain Adjustment Bracket Slack in chain...

  • Page 44: Carriage Wheel Alignment

    Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual CARRIAGE WHEEL ALIGNMENT If either the front-right carriage wheel and/or the rear-right carriage wheel are still not seated properly on the track rail after CARRIAGE WHEEL ADJUSTMENT (page 34), then the chain needs to skip a link on the front-right carriage wheel arm.
  • Page 45 Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual Reseat the chain on the carriage wheel arm sprocket. If the CARRIAGE WHEEL ALIGNMENT section on page 42 was necessary, return to the CARRIAGE WHEEL ADJUSTMENT section on page 40 before proceeding with install. 0003389-M-EN: Rev B Page 10-Jun-2022...

  • Page 46: Levelling The Carriage

    Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual LEVELLING THE CARRIAGE Once the carriage wheels are seated firmly on the track rail and the chain is tight with no slack, the sawhead can be levelled. Roll the sawhead forward until the blade is over one of the track bunks. Measure the distance from the blade-to-bunk on the left-side and then measure the distance on the right-side.

  • Page 47: Gas Spring

    Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual 9. GAS SPRING Using the hardware listed below, connect the gas spring to the chain lever. M10 X 45 mm M10 Flat Hex Bolt Washer M10 Lock Nut This step requires the assistance of one or more people. Lift the right side of the sawhead approximately 2 in [50 mm] off the setup blocks.
  • Page 48 **Assemble the gas spring to the chain lever using the upper lever hole for HM122, the middle hole for HM130 & HM130MAX, and the bottom lever hole for HM126.** With the chain lever angled back, assemble the gas spring to the chain lever using one (1) M10 X 45 mm hex bolt, two (2) M10 flat washers, and one (1) M10 lock nut.

  • Page 49: Indexing Handle

    Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual 10. INDEXING HANDLE Using the hardware listed below, assemble the indexing handle and then connect it to the chain lever. M12 X 90 mm Handle Grip Hex Bolt M12 X 110 mm Indexing Socket Head Handle...
  • Page 50 Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual Assemble the plastic revolving handle to the end of the indexing handle using one (1) M12 lock nut. Then assemble the M12 X 90 mm hex bolt, two (2) flat washers, and double M12 lock nut stack to the curved slot.
  • Page 51 Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual Set the first notch in the indexing handle over the push handle spacer. Tighten the curved slot bolt and nut once seated. Do not move the chain lever when tightening the hardware. 1.

  • Page 52: Carriage Wheel Sweepers

    Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual 11. CARRIAGE WHEEL SWEEPERS Assemble each sweeper bracket prior to installing them to the lap siding attachment. Wheel Sweeper Assembly Remove one of the M20 lock nuts and M20 flat washers securing the carriage wheel to the carriage wheel arm.
  • Page 53 Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual Install the wheel sweeper assemblies onto the M20 X 75 mm hex bolts using the M20 flat washers and M20 lock nuts that were removed in the previous step. On the front carriage wheel, position the wheel sweeper assembly vertical (90°) in relation to the track.

  • Page 54: Track Rail Extensions

    Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual 12. TRACK RAIL EXTENSIONS Using the hardware listed below, assemble a track rail extension and extended carriage stop to each end of the right-side sawmill track rails. M10 X 30 mm Flanged Hex Rail Extension Bolt M10 Flanged...
  • Page 55 Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual Next, assemble a rail extension and extended carriage stop to each end of the right-side track rails using four (4) M10 X 30 mm flanged hex bolts and four (4) M10 flanged lock nuts per end. M10 X 30 mm Extended carriage stops mount to inside...

  • Page 56: Setup Block Removal

    Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual 13. SETUP BLOCK REMOVAL With the lap siding attachment assembly complete, remove the two (2) setup blocks from the track rail. Be sure to store these components and associated hardware in case the lap siding attachment is removed in the future.

  • Page 57: Operation

    Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual OPERATION ANGLING THE SAWHEAD To angle the sawhead, first lift the indexing handle up off the push handle spacer. 0003389-M-EN: Rev B Page 10-Jun-2022...
  • Page 58 Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual Then, while holding the push handle to prevent the carriage from rolling, pull the indexing handle towards the rear. The right-side of the carriage will rise as the lever is pulled. Pull indexing handle straight back with left hand.
  • Page 59 Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual Finally, set the desired notch in the indexing handle over the push handle spacer to lock the sawhead in at that angle. Set the desired notch over the push handle spacer to lock the indexing handle.

  • Page 60: Lap Siding Cut Method

    Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual LAP SIDING CUT METHOD Before lap siding boards can be cut, first mill a log to an appropriate square cant size to achieve the desired board width. Then follow these steps to cut the canted lumber to minimize waste: 1.

  • Page 61: Trailer Lock-Down

    The lap siding kit comes with two (2) travel hooks with wire rope lanyards that are used to lock the sawhead carriage to the track. HM126 & HM130(MAX) kits also include hardware for mounting the hooks to Woodlander sawmill trailers with extensions (XL versions only).
  • Page 62 Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual The hooks act as a vertical carriage stop, preventing the lap siding attachment from sustaining damage when the tie-down strap is tightened while readying the sawmill trailer for transport. Note that the carriage will not sit level when locked-down for transport. This is normal. Sawhead will not be level Tie down strap pulling down...
  • Page 63 Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual On Woodlander and Woodlander MAX sawmill trailers without extensions, temporarily remove two (2) of the M10 X 30 mm flanged hex bolts from the track reinforcement plate and then reassemble them through the lanyard eyelets. Reuse M10 X 30 mm bolts and M10 lock nuts from track.
  • Page 64 Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual On Woodlander XL and Woodlander XL MAX sawmill trailers with extensions, use the two (2) M10 X 25 mm flanged hex bolts and M10 flanged lock nuts and assemble the travel hooks through the nearest open thru holes in the right side track rail.

  • Page 65: Replacement Parts Ordering

    Record the part number (e.g. 0001071, HHB-MBM080FCJ, etc.) in the “Part No.” column. Contact Woodland Mills through the website or via phone/email. If possible, include the invoice or sales number from the purchased product so an associated account can be located. If the account has multiple addresses on file, please indicate to which address the replacement...

  • Page 66: Exploded Assembly Views

    Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual EXPLODED ASSEMBLY VIEWS CARRIAGE WHEEL ARM
 0003389-M-EN: Rev B Page 10-Jun-2022...

  • Page 67: Wheel Sweeper

    Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual WHEEL SWEEPER
 0003389-M-EN: Rev B Page 10-Jun-2022...

  • Page 68: Chain Adjustment Bracket

    Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual CHAIN ADJUSTMENT BRACKET
 0003389-M-EN: Rev B Page 10-Jun-2022...

  • Page 69: Rear Idler [Hm122]

    Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual REAR IDLER [HM122]
 0003389-M-EN: Rev B Page 10-Jun-2022...

  • Page 70: Rear Idler [Hm126 & Hm130(Max)]

    Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual REAR IDLER [HM126 & HM130(MAX)]
 0003389-M-EN: Rev B Page 10-Jun-2022...

  • Page 71: Indexing Handle & Lever

    Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual INDEXING HANDLE & LEVER
 0003389-M-EN: Rev B Page 10-Jun-2022...

  • Page 72: Track Rail Extension, Travel Hooks, Cable Chain

    Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual TRACK RAIL EXTENSION, TRAVEL HOOKS, CABLE CHAIN
 ** Blackened item balloons are used on Woodlander XL and Woodlander XL MAX sawmill trailers only. ** 0003389-M-EN: Rev B Page 10-Jun-2022...

  • Page 73: Parts List

    0002826 CARRIAGE STOP 0003724 TRAVEL HOOK W/ LANYARD, HM122 0003188 TRAVEL HOOK W/ LANYARD, HM126/HM130(MAX) 0002913 SETUP BLOCK 6000-2RS BALL BEARING, SEALED, 10 mm SFT, 26 mm HSG, 8 mm WD BALL BEARING, SEALED, ANG-CONT, DOUBLE ROW, 20 mm SFT, 5204-2RS 47 mm HSG, 20.6 mm WD...
  • Page 74 Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual Quantity Item Part No. Description HM126 HM130 HM122 HM130 HHB-MBE075FCJ HEX HEAD BOLT, CLS 8.8, M6 X 1, 20 mm LG, FULL HHB-MBM075FCJ HEX HEAD BOLT, CLS 8.8, M10 X 1.5, 20 mm LG, FULL HHB-MBM090FCJ HEX HEAD BOLT, CLS 8.8, M10 X 1.5, 35 mm LG, FULL...

  • Page 75: Notes

    Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual NOTES 0003389-M-EN: Rev B Page 10-Jun-2022...
  • Page 76 Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual 0003389-M-EN: Rev B Page 10-Jun-2022...
  • Page 77 Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual 0003389-M-EN: Rev B Page 10-Jun-2022...
  • Page 78 Sawmill Accessory: 2020-2022 Lap Siding Attachment Operator’s Manual 0003389-M-EN: Rev B Page 10-Jun-2022...
  • Page 79 
 This page intentionally left blank.

This manual is also suitable for:

Hm130max

Table of Contents