1. Manuals
  2. Brands
  3. JANUS INTERNATIONAL Manuals
  4. IP Access Controllers
  5. Noke Screen
  6. Installation manual

JANUS INTERNATIONAL Noke Screen Installation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Installation
Guide
www.janusintl.com/noke

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Noke Screen and is the answer not in the manual?

Questions and answers

Summary of Contents for JANUS INTERNATIONAL Noke Screen

  • Page 1 Installation Guide www.janusintl.com/noke...

  • Page 2: Before Starting

    INTRODUCTION Before Starting This installation guide provides instructions for installing a Nokē Screen in various settings such as pedestrian gates, parking entries, and interior pedestals. The Nokē Screen controls existing electronic locks. This guide is intended for licensed electricians and trained technicians only.

  • Page 3: Specifications

    SPECIFICATIONS Dimensions 2in. x 0.8in. x 5in. (5cm. x 2cm. x 12.7cm) Material Polished Zinc Connectivity Bluetooth enabled, WiFi Power 12V - 24V DC input (requires 2 Amp capable), PoE Backup Battery None (backup from power supply switch) Lock Activation 850mA / 0.01-25 Sec.

  • Page 4: Installation

    INSTALLATION Installing the Backplate Before drilling into walls, make sure there are no water or electrical lines in the way. For wall mounting, use a pencil to trace the desired back plate holes onto the wall. Then, drill the holes in the wall and set the anchors. If mounting on any masonry exterior walls, use machine screws for metal plates and toggle screws for interior drywall.
  • Page 5 INITIALIZATION Wiring When using PoE for power and data, connect the CAT6 into the control board port as shown below. No devices other than Nokē products should be plugged into the switch. Use approved conduit only--never run high voltage inside. Always adhere to all local building and electrical codes.
  • Page 6 INITIALIZATION When not using PoE for power and data, use an Altronix power supply to power Nokē Screen. Data will need to be provided via WiFi. First, connect the power supply wire (12V- 24V DC) and both the ground (GND) and earth ground (ESD GND) wires to their relay push pin connectors on the relay board, and then insert the relay board into the control board.
  • Page 7 INITIALIZATION Setting Up the Application To initialize the Nokē Screen, you can either gather information from the unit and submit it online or use the Nokē Smart Entry mobile device application (available on Google Play/Apple stores). The website is: www.smartentry.noke.com. Before initializing the device, you need a Nokē...
  • Page 8 INITIALIZATION Press Upload. Go to the menu page (icon on the upper- right corner of the app) and press Add Gateway. Name the gateway with a similar name to the device name. 10. Use the Comments section to record how the device was wired (for example, PoE, 12V D.C. etc.).
  • Page 9 INITIALIZATION 11. Press Save and Finish.
  • Page 10 INITIALIZATION 12. Press the + button in the upper right-hand corner of the app to add your device. 13. Using the app, scan the QR code on the Nokē Screen display. 14. After scanning, name your device and select what type of entry it controls (for example, gate, door, elevator, sliding door, etc.).
  • Page 11 INITIALIZATION 15. When finished, press Done.
  • Page 12 INITIALIZATION Connecting to WiFi Before connecting the Nokē Screen keypad to the WiFi, you need your device’s SSID and password. Usually, you can find this on the bottom of your device. To connect to WiFi, From the Nokē Smart Entry Web Portal, select Settings > WiFi, and then select the + icon in the top-right corner.
  • Page 13 DIAGRAMS Providing Power and Data Cat6 Cat6 18/2 Router Gate PoE Switch Nokē Screen PoE Office Switch Cat6 Cat6 18/2 18/2 Router Gate Power Supply Nokē Screen (Altronix) Non-PoE Office...
  • Page 14 MOUNTING Considerations Before installing a Nokē Screen, consider how it will be used. For example, if the Nokē Screen is for cars at a gate, you should ensure the keypad can be reached from the driver side window. For Nokē Screens that will be operated by those walking up to a facility, the Nokē Screen should be mounted so pedestrians (and those with disabilities) can reach the keypad with ease.
  • Page 15 MOUNTING Options For walk up access, the Nokē Screen is weather resistant and can be mounted on external walls or on a goose-neck pedestal (see below). Automatic Sliding Door Pedestal Mounted...
  • Page 16 MOUNTING Elevator Conventional Door...

  • Page 17: Maintenance

    Nokē Screen by its customers. Nokē or Janus International also cannot be held liable for any and all errors in this manual or for any incidental or consequential damages that result for the use of the material presented in this manual.
  • Page 18 FCC Statement Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

Table of Contents