Figures - ABB HT562624 Operation Manual

Operation Manual / 4 Product description / A150-M.. - A155-M..

Figures

Figures
Fig. 1 Layout and function of the tur-
bocharger ..................................
Fig. 2 Compressor wheel cooling ........
Fig. 3 Warning plate locations .............
Fig. 4 Locations of the rating plates ....
Fig. 5 Suspension of complete turbo-
charger unit ...............................
Fig. 6 Removing the turbocharger .......
Fig. 7 Loosening the clamping nut ......
Fig. 8 Turbocharger centre of gravity ..
Fig. 9 Inserting the gasket ...................
Fig. 10 Fitting the turbocharger 1 ..........
Fig. 11 Fitting the turbocharger 2 ..........
Fig. 12 Preparing the clamping nut for
the tightening procedure ..........
Fig. 13 Tightening pressure screws ......
Fig. 14 Connecting the compressor
cooling air intake .......................
Fig. 15 Attaching the support ................
Fig. 16 Oil orifice ...................................
Fig. 17 Layout and overview of speed
measurement system ................
Fig. 18 Replacing the speed sensor ......
Fig. 19 Noise insulation, bellows ...........
Fig. 20 Carrying out wet cleaning of
compressor ...............................
Fig. 21 Carrying out wet cleaning of
turbines .....................................
Fig. 22 Cleaning the filter silencer .........
Fig. 23 Compressor-end, non-rotating
parts ..........................................
Fig. 24 Turbine end, non-rotating parts .
Fig. 25 Soaking the turbine end ............
Fig. 26 Weights of assemblies ..............
Fig. 27 Removing the air inlets ..............
Fig. 28 Removing the insulation ............
Fig. 29 Removing the gas outlet casing
Fig. 30 Dismantling the gas outlet
flange ........................................
© Copyright 2017 ABB. All rights reserved.
Fig. 31 Removing the gas outlet flange . 76
6
Fig. 32 Removing the compressor cas-
7 ing ............................................. 77
8 Fig. 33 Dismantling the diffuser and the
wall insert .................................. 78
9
Fig. 34 Press off the casing ................... 79
11 Fig. 35 Oil orifice ................................... 80
12 Fig. 36 Removing insulation sheets ...... 80
13 Fig. 37 Removing cartridge group 1 ...... 81
14 Fig. 38 Removing cartridge group 2 ...... 82
15 Fig. 39 Removing the nozzle ring .......... 83
16 Fig. 40 Measuring clearance A and B ... 84
17 Fig. 41 Nozzle ring compression PD ..... 85
Fig. 42 Installing the nozzle ring ............ 86
18
Fig. 43 Installing the cartridge group 1 .. 87
19
Fig. 44 Installing the cartridge group 2 .. 88
Fig. 45 Fitting the wall insert and the
20
diffuser ...................................... 89
20
Fig. 46 Installing the compressor casing
22 .................................................. 90
Fig. 47 Measuring clearances N and R . 91
30
Fig. 48 Installing the air inlets ................ 92
32
Fig. 49 Removing the insulation sheets . 94
34
Fig. 50 Removing the turbine casing ..... 95
Fig. 51 Installing the turbine casing ....... 96
45
Fig. 52 Installing the gas outlet flange ... 97
Fig. 53 Fitting the insulation .................. 98
49
Fig. 54 Installing the gas outlet casing .. 99
50
Fig. 55 Fitting the insulation .................. 100
52
Fig. 56 Overview of tightening torques .. 101
53
Fig. 57 Tightening torques for insulation 102
56
Fig. 58 Fitting the cover plate ................ 105
70
Fig. 59 Cover plate drawing .................. 106
71
Fig. 60 Dimensions for cover plate ........ 107
72
Fig. 61 Overview of part numbers ......... 114
73
75
HZTL4032_EN
Page 117 / 120
Revision F January 2017