Download
Share
Print this page
  1. Manuals
  2. Brands
  3. ALLDATA Manuals
  4. Industrial Equipment
  5. S3000
  6. Manual

ALLDATA S3000 Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
Fuse Block |Service and Repair, Procedures: Underhood Electrical Center...
REMOVAL PROCEDURE
1. Disconnect the negative battery cable.
2. Remove the left fender upper brace.
1 of 10
http://repair.alldata.com/alldata/article/display.action?componentId=117...
6/10/2013 5:10 PM

Advertisement

loading
Need help?

Need help?

Do you have a question about the S3000 and is the answer not in the manual?

Questions and answers

Summary of Contents for ALLDATA S3000

  • Page 1 Fuse Block |Service and Repair, Procedures: Underhood Electrical Center... http://repair.alldata.com/alldata/article/display.action?componentId=117... REMOVAL PROCEDURE 1. Disconnect the negative battery cable. 2. Remove the left fender upper brace. 1 of 10 6/10/2013 5:10 PM...
  • Page 2 Fuse Block |Service and Repair, Procedures: Underhood Electrical Center... http://repair.alldata.com/alldata/article/display.action?componentId=117... 3. Remove the electrical center brace cover assemble by lifting the cover (3) outwards to clear the tabs. 4. Remove all fuses and relays. 2 of 10 6/10/2013 5:10 PM...
  • Page 3 Fuse Block |Service and Repair, Procedures: Underhood Electrical Center... http://repair.alldata.com/alldata/article/display.action?componentId=117... 5. Push on the tab (3) 50 that the electrical center can be rotated on the studs located at (2). 6. Remove all connectors by removing the bolt (1) for each connector.
  • Page 4 Fuse Block |Service and Repair, Procedures: Underhood Electrical Center... http://repair.alldata.com/alldata/article/display.action?componentId=117... 8. Push on the tabs (2) in order to lift the electrical center (1) out of the housing. 4 of 10 6/10/2013 5:10 PM...

  • Page 5: Installation Procedure

    Fuse Block |Service and Repair, Procedures: Underhood Electrical Center... http://repair.alldata.com/alldata/article/display.action?componentId=117... 9. To replace the engine electrical center bracket remove the 4 retaining bolts (1). 10. Remove the engine electrical center bracket assembly from the fender. INSTALLATION PROCEDURE 5 of 10...
  • Page 6 Fuse Block |Service and Repair, Procedures: Underhood Electrical Center... http://repair.alldata.com/alldata/article/display.action?componentId=117... 1. Install the engine electrical center bracket assembly to the front fender. NOTE: Refer to Fastener Notice in Service Precautions. 2. Install the 4 retaining bolts (1). Tighten Tighten the 4 retaining bolts (1) to 9 N.m (80 lb in).
  • Page 7 Fuse Block |Service and Repair, Procedures: Underhood Electrical Center... http://repair.alldata.com/alldata/article/display.action?componentId=117... 3. Align the electrical center block (1) stubs in the slots so that the tabs (2) retains it in place. 7 of 10 6/10/2013 5:10 PM...
  • Page 8 Fuse Block |Service and Repair, Procedures: Underhood Electrical Center... http://repair.alldata.com/alldata/article/display.action?componentId=117... 4. Connect the wire connectors to the lower portion of the electrical center block. 5. Connect the wire connectors with the bolts to the electrical center block. Tighten Tighten all connector bolts (1) to 9 N.m (80 lb in).
  • Page 9 Fuse Block |Service and Repair, Procedures: Underhood Electrical Center... http://repair.alldata.com/alldata/article/display.action?componentId=117... 8. Install the lower part of the cover (1). 9. With the cover (2) off, use the fuse location information to install all fuses and relays. 10. Install the cover.
  • Page 10 Tighten the 4 retaining bolts to 25 N.m (18 lb ft). 13. Connect the negative battery cable. 14. Start vehicle and ensure all components function properly. © 2013 ALLDATA, LLC. All Rights Reserved. (Version 2.0.13469) 10 of 10 6/10/2013 5:10 PM...