Table of Contents
Advertisement
Quick Links
Vision™PLC+HMI
V130-33-TA24/V130-J-TA24
V350-35-TA24/V350-J-TA24
V350-S-TA24/V350JS-TA24
V430-J-TA24
General Description
All of the controllers covered in this guide are micro-PLC+HMIs, rugged programmable logic controllers
that comprise built-in operating panels and on-board I/Os.
Item
On-board I/O
Screen
Keypad
Function Keys
Com Port, Built-in
RS232/485
USB device,
mini-B
The user may install a CANbus port (V100-17-CAN), and one of the following:
Com Ports, separate
order, user-installed
* V430J/V350/V350J/V350S/V350JS comprises both RS232/485 and USB ports; note that only one channel may be
used at a time.
Standard Kit Contents
Item
Controller
Terminal Blocks
Battery (installed)
Slides
(2 sets of key labels)
Mounting Brackets
Rubber Seal
Programming cable
+ RS232 adapter
USB
programming cable
Unitronics
Installation Guide
12 Digital Inputs, including 2 Analog,
2 PT100/TC ,1 HSC/Shaft-encoder input
10 Transistor Outputs, 2 Analog Outputs
V130-TA24
V130-J-TA24
2.4"
Yes
None
Yes
Yes
None
None
RS232/RS485 port (V100-17-RS4/V100-17-RS4X)
Ethernet (V100-17-ET2)
Profibus Slave (V100-17-PB1)
V130-TA24
V130-J-TA24
None
Yes (2 parts)
Yes
None
V350-TA24/V350-J-TA24
V350-S-TA24/V350-JS-TA24
Model Dependent
3.5" Color Touch
Yes*
Yes*
V350-TA24/V350-J-TA24
V350-S-TA24/V350-JS-TA24
Yes
Yes
Yes
Yes
Yes
V430-J-TA24
4.3" Color Touch
None
Yes
Yes*
Yes*
Yes*
Yes*
V430-J-TA24
None
Yes (4 parts)
None
Yes
1
Advertisement
Table of Contents
Related Manuals for Unitronics Vision V130-J-TA24
Summary of Contents for Unitronics Vision V130-J-TA24
- Page 1 Standard Kit Contents V130-TA24 V350-TA24/V350-J-TA24 V430-J-TA24 Item V130-J-TA24 V350-S-TA24/V350-JS-TA24 Controller Terminal Blocks Battery (installed) Slides None None (2 sets of key labels) Mounting Brackets Yes (2 parts) Yes (4 parts) Rubber Seal Programming cable None + RS232 adapter None programming cable Unitronics...
-
Page 2: Alert Symbols And General Restrictions
All examples and diagrams are intended to aid understanding, and do not guarantee operation. Unitronics accepts no responsibility for actual use of this product based on these examples. Please dispose of this product according to local and national standards and regulations. -
Page 3: Panel Mounting
4. Tighten the bracket’s screws against the panel. Hold the bracket securely against the unit while tightening the screw. 5. When properly mounted, the controller is squarely situated in the panel cut-out as shown in the accompanying figures. V130/V130J/V350/V350J/V350S/V350JS Unitronics... - Page 4 DIN-rail Mounting (V130/V130J/V350/V350J/V350S/V350JS ) 1. Snap the controller onto the DIN rail as shown in the figure to the right. 2. When properly mounted, the controller is squarely situated on the DIN-rail as shown in the figure to the right. Unitronics...
-
Page 5: Wiring Procedure
- If input 0 is set as a high-speed counter (without reset), input 1 can function as a normal digital input. Inputs 7-8 and 9-10 can function as digital, thermocouple, or PT100 inputs; Input 11 can also serve as the CM signal for PT100. Unitronics... - Page 6 Analog Output 0: Set to Voltage/Current Digital* Set to JP13 Voltage Voltage* Current Current Input 6: Set Type - Digital or Analog #2 Set to Analog Output 1: Set to Voltage/Current Digital* Set to JP14 Voltage Voltage* Current Current *Default settings Unitronics...
- Page 7 Vision™PLC+HMI I/O Wiring npn (sink) Input Input wiring HSC input wiring pnp (source) Input Input wiring HSC input wiring Shaft-encoder Unitronics...
- Page 8 PT100 (Sensor 0): use Input 9 and 10, related to CM signal. PT100 (Sensor 1): use Input 7 and 8, related to CM signal. 4 wire PT100 can be used by leaving one of the sensor leads unconnected Unitronics...
-
Page 9: Power Supply
To maximize system performance, avoid electromagnetic interference by: Mounting the controller on a metal panel. Connect each common and ground connection directly to the earth ground of your system. For ground wiring uses the shortest and thickest possible wire. Unitronics... - Page 10 To do so, remove the RS485 connector (pins 1 & 6) from the PLC and connect a standard RS232 programming cable. Note that this is possible only if DTR and DSR signals of RS232 are not used (which is the standard case). Unitronics...
- Page 11 ** Causes the unit to function as an end unit in an RS485 network USB Port The USB port is not isolated. Caution Make sure that the PC and the controller are grounded to same potential. The USB port may be used for programming, OS download, and PC access. Unitronics...
-
Page 12: Opening The Controller
Note that you must replace the back cover securely before powering up the controller. The information in this document reflects products at the date of printing. Unitronics reserves the right, subject to all applicable laws, at any time, at its sole discretion, and without notice, to discontinue or change the features, designs, materials and other specifications of its products, and to either permanently or temporarily withdraw any of the forgoing from the market.
Need help?
Do you have a question about the Vision V130-J-TA24 and is the answer not in the manual?
Questions and answers