Magnet damper method Accuracy Emitted laser ±1 mm / 10 m *(Before shipment from factory) 2-vertical line 90°±0.01° Power supply Makita battery cartridge Rated Voltage D.C.10.8V - 12Vmax Operating time At 4-vertical line/ At 2-vertical line/ At Vertical line/ (when BL1016 is used)
* Specifications and battery cartridge may differ from country to country. * The weight may differ depending on the battery cartridge. The lightest and heaviest combination, according to EPTA-Procedure 01/2014, are shown in the table. NOTE: When used at 0°C or lower temperatures, the laser lines are weak just after turning the power on.
CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Safety Declaration This product complies with the following standards: • EN61326-1: Electrical equipment for measurement, control and laboratory use – EMC requirements •...
Noise Related Safety Standards • FCC Part15 SubpartB/ICES 003 CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Page 8
WARNING - Electrical safety 1. Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. 2. Do not expose the product to rain or wet conditions. Water entering the product will increase the risk of electric shock.
Page 9
WARNING - Additional safety Use the correct accessories. Use only accessories recommended in this User's Manual and in Makita catalogs. Do not use other accessories since this might result in malfunction, accident or injury. 9 ENGLISH...
Page 10
If the laser is not emitted even after shaking this product lightly a few times, immediately stop work, and contact the store of purchase or the nearest Makita sales office. 6. When the power is turned ON, the product emits the laser beam in the same mode that was turned OFF last time.
Page 11
17. With regards to safety education, the user must fully understand the nature and danger of laser beams. 18. The product is not intended for use by persons including children with reduced physical, sensory or mental capabilities, or lack of experience and knowledge.
Page 12
Use of non-genuine Makita batteries, or batteries that have been altered, may result in the battery bursting causing fires, personal injury and damage. It will also void the Makita warranty for the Makita tool and charger. Tips for maintaining maximum battery life 1.
Makita sales office. CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.
NOTE: Some items in the list may be included in the tool package as standard accessories. They may differ from country to country. Installing or removing battery cartridge CAUTION • Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool.
CAUTION • Always install the battery cartridge fully until the red indicator cannot be seen. If not, it may accidentally fall out of the tool, causing injury to you or someone around you. • Do not install the battery cartridge forcibly. If the cartridge does not slide in easily, it is not being inserted correctly.
Using the Multi Line Laser 1. Installing the Multi Line Laser Set this product on a level surface. Turn the adjustment screw leg so that the bubble in the circular level comes to the center of the red circle. Circular level When using the tripod, first set down the tripod.
2. Operating the power switch 1. Power switch [Power ON] Turn the power switch to the "I/ON" side. The laser beam is emitted. [Power OFF] Turn the power switch to the "O/OFF" side. The power turns OFF, and the pendulum inside is locked.
Select the line beam emission mode by the line selection switch on the operation panel. Line selection switch SK40GD [Loopback switch system] Lower dot beam Lower dot beam Lower dot beam SK20GD [Loopback switch system] Lower dot beam Lower dot beam 18 ENGLISH...
Page 19
SK10GD [Loopback switch system] Lower dot beam Lower dot beam NOTE: The height of the horizontal line beam can be easily adjusted by using the tripod (optional accessory). It can be fine-adjusted from either side by turning the fine-adjustment knob. 1: Fine-adjustment knob Fine-adjustment mechanism The stand prevents the product from toppling over.
CHECKING THE ACCURACY ■ Should the line laser exceed the permissible difference during the checking, contact the store of purchase or a Makita authorized service center. 1. Checking the horizontal line 1. Place the line laser near the center of a room with approx. 5 m walls.
2. Checking the plumbing point and vertical line 1. Set the “plumb” on the wall approx. 3 m above the floor. 2. Place the line laser 3 to 5 m away from the wall. 3. Adjust the attitude so that the bubble in the level comes to the center of the red circle.
3. Checking the 180°vertical line 1. Make a mark on the floor near the center of a room with 4 to 6 m walls. 2. Emit the vertical line beam. 3. Mark A near the center of the vertical laser line on the right wall, and mark B near the center of the "90°vertical laser line"...
4. Checking the 90°vertical line 1. Make a mark on the floor near the center of a room with 4 to 6 m walls. 2. Emit all vertical line beams. 3. Mark A near the center of the vertical line on the right wall, and mark B near the center of the "90°vertical line"...
Page 24
[SK20GD] 1. Make a mark on the floor near the center of a room with 4 to 6 m walls. 2. Emit all vertical line beams. 3. Mark B and C near the center of the vertical line on the front and left wall.
Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELIABILITY, repairs, any maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. 25 ENGLISH...
Page 26
Makita Europe N.V. Jan-BaptistVinkstraat 2, 3070 Kortenberg, Belgium Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo,Aichi 446-8502 Japan www.makita.com...