Related Manuals for STM ATOMIC CLOSER
Summary of Contents for STM ATOMIC CLOSER
- Page 1 ( 5 0 9 ) 2 0 4 - 3 1 4 8 ( C A L L O R T E X T ) | S T M C A N N A . C O M | S A L E S @ S T M C A N N A . C O M...
- Page 2 ATOMIC CLOSER WEIGHT & Approximately 100 lbs DIMENSIONS Machine Dimensions 32" L x 33" H x 18" W USER MANUAL V1.0 VOLUME 72 Per Cycle CAPACITY Standard 120V, 60 Hertz POWER 5.1 Full Load Amps 5-1/2 ft. Cord Length Encased in Powder-Coated Aluminum MATERIALS Aluminum &...
- Page 3 TABLE OF CONTENTS Table of Contents .......... 1 Helpful Tips ..........5 Components ........... 2 Cleaning & Maintenance ......6 Start-Up Operation ........3 Troubleshooting .......... 7 Touch Screen ..........4 Terms of Business ........8...
- Page 4 COMPONENTS Plastic Casing Motor Motor Tray Cart 7" Touch Screen Cart Guide Rod Motor Lift Plate Power Button Rubber Feet Cone Chute...
- Page 5 START-UP OPERATION Step 1: Turn the machine on using the on Step 4: Load tray into the cart located just behind off switch on the side of the machine. the touch screen. Step 2: Select cone size: Watch cones on sides to make sure they all get Located on the top left corner of the set on bottom tray.
- Page 6 START-UP OPERATION Step 6: Fix nicked/crushed cones using the Step 8: Check how far paper is sticking out above chopstick or pen. Ensure that the top of the the tray. You will want .250-.300” coming out of joint is not crushed or bent from use in the the top of the cone holders in order to get a good Rocketbox.
- Page 7 TOUCH SCREEN Home Screen This is the main screen for Operating the Closer. You can Start, Stop and Reset the machine from this screen. Pre-Roll Selection Dropdown Choose the correct pre-roll size of your tray. This will raise or lower the Lift Table to work properly with your tray size.
- Page 8 CLEANING & MAINTENANCE Daily Maintenance Remove trays from machine. Power-off machine completely. Blow out loose material with can of air. Carefully, wipe down tray cart, lift table, rods, pincher jaws, and outside of machine with isopropyl alcohol on a microfiber cloth. Home the machine and run through a cycle.
- Page 9 TROUBLESHOOTING 1. Bottom tray with joints is full, but not all of them are poking up out of tray when I load it into box: Check bottom of joints not poking up - Might have been crushed, bent on the bottom half. Load more carefully - Put tray in at angle, setting joints on left or right side JUST on the edge of the bottom tray, then slowly drop other side.
- Page 10 If there is not a "Reset" button, select the "Stop" button, followed by the "Reset" button to reset the machine. If the Atomic Closer is making a loud noise during operation or something that does not sound correct. Press the stop button and power down machine with power button at rear of machine.
- Page 11 It is very important to fill and pack joints properly for the best success with closes. Review training documentation and videos on how to operate the RocketBox or Mini-RocketBox prior to using the Atomic Closer. Contact Client services at clientservices@stmcanna.com or call (509) 204-3164 to schedule video training.
- Page 12 4-8 weeks or more from payment date, unless otherwise stated. Following the receipt of an invoice, STM Canna must receive payment within a maximum of 7 days before the invoice expires – leaving lead times, quoted prices, specials and discounts on all items subject to change.
- Page 13 TERMS All orders must be paid in full before the order is placed. Order quotes expire within 10 days. STM Canna & STM Supply reserve the right to specify collection by certified check, money order, or company check. Personal checks are not accepted.
- Page 14 We may ask you for pictures, video, descriptions, and other identifying information to make a determination. If you are unable to provide adequate documentation requested, your return request will be denied. If your item is deemed defective, which is solely at STM’s discretion, we will issue you an RMA # which you will need to place in and on the package.
- Page 15 LIABILITY The purchaser of any products releases the manufacturer of those parts and STM Canna from all liabilities pertaining to use of the products. CLAIMS Since ownership of product transfers at the FOB point, claims for damaged, lost, or short shipments must be made at the time of receipt.
Need help?
Do you have a question about the ATOMIC CLOSER and is the answer not in the manual?
Questions and answers