Related Manuals for Producer's PRIDE Ranch Chicken Coop
Summary of Contents for Producer's PRIDE Ranch Chicken Coop
- Page 1 SKU: 1237423 Ranch Chicken Coop (102.4 in.L*63.0 in.W*75.7in. H) Distributed by: TRACTOR SUPPLY COMPANY 5401 VIRGINIA WAY, BRENTWOOD, TN 37027 For customer support, call: 1-888-376-9601 www.TractorSupply.com MADE IN CHINA...
-
Page 2: Care Instructions
CARE INSTRUCTIONS SAFETY INFORMATION: WARNING: Please keep children out of assembly area during assembly. WARNING: This product is designed exclusively for chickens. Not intended for children. BEFORE YOU BEGIN: Read instruction prior to assembly. This product contains parts that can be damaged if incorrectly assembled. - Page 3 PARTS LIST Part Image Description Quantity 2pcs Left Roof Panel 2pcs Right Roof Panel Right Coop Panel Left Coop Panel Left Run Panel 2pcs Front&Back Run Panel...
- Page 4 Front Middle Run Panel Back Middle Run Panel Right Side Run Panel Front Coop Panel Back Coop Panel Side Panel of Nesting Floor Panel of Nesting Nesting Box Lid with hinges...
- Page 5 Drawer Base Frame Drawer Ladder Roof cap Roof cap Door Panel Top Cap Nesting box divider 3pcs 6pcs Wooden Support Bars 2pcs Wooden Support Bars Roosting Bar 2pcs...
- Page 6 4+1pcs Screws 12mm 14+1pcs Screws 14mm 2pcs Screws 30mm 16+1pcs Screws 35mm 58+2pcs Screws 40mm 16+1pcs Screws 50mm Door pull lever Support Arm 1pair...
-
Page 7: Assembly Instruction
CAUTION: If using a cordless power drill / screwdriver, turn torque setting down to a minimum level to start so that screws are not stripped. Adjust torque up slightly if needed to fully tighten screws. ASSEMBLY INSTRUCTION Step 1: Attach the Front Coop Panel (10) and the Back Coop Panel (11) to the Right Side Run Panel (9) using screws (E)*4pcs. - Page 8 Step 3: Place the Drawer Base Frame (15) in place first, and then place the Drawer (16). Install the Roosting Bar (24) as shown. Step 4: Attach the Side Panel of Nesting Box (12) using screws(E)*4pcs as shown. *** Note: You must open the chicken run door first to install 2 of the screws (F) *2 pcs as seen in the picture below.
- Page 9 Step 5: Place the Floor Panel of Nesting Box (13) into the nesting box. And then install the Nesting Box Dividers(21) as shown. Step 6: Mount the Nesting Box Lid with hinges (14) to the coop using screws(B)* 6pcs as shown.
- Page 10 Step 7: Open the nesting box lid, and attach the Support Arm(H) using screws(B)* 8pcs. ***Note the different direction of support arms. Step 8: Attach the Ladder (17) to the coop using screws(C)*2pcs as shown.
- Page 11 Step 9: Attach the Front Middle Run Panel (7) and Back Middle Run Panel (8) to the coop using screws (F)*6pcs as shown. Step 10: Attach the Front & Back Run Panel (6) using screws (F)*6pcs as shown.
- Page 12 Step 11: Attach the Left Run Panel (5) to the run panels using screws (E)*6pcs as shown. Step 12: Attach the Door Panel Top Cap (20) to the left run panel, using screws (F)*2pcs as shown.
- Page 13 Step 13: Locate the Right Roof Panel (2) and position it on the ground with wooden frame side up and the metal extension on your left side as seen in the picture below. Next place the Wooden Support Bars (22) in place on the wooden frame (see picture below) and secure in place with 3 screws each (E).
- Page 14 Step 14: Next, place the Left Roof Panel (1) on the ground with wooden frame facing up. Position the Support Bars (22, 23) in place as per picture below and secure in place with 3 screws each (E). ***NOTE: The orientation of the wooden support bar before screwing in place. The Angle cut should be facing the center of the panel with the long end of the angle on top as noted in picture.
- Page 15 Step 15: Attach Roof caps(18)(19) using screws (E)*8pcs. Finally,use screws (A) to secure the overlap of metal roof as shown in picture below. Step 16: Place the Door Pull Lever(G) through hole in panel, and secure into place by threading into door hardware located at the center of the sliding coop door.
- Page 16 Finished Coop...
Need help?
Do you have a question about the Ranch Chicken Coop and is the answer not in the manual?
Questions and answers