1. Manuals
  2. Brands
  3. Shaver Manuals
  4. Industrial Equipment
  5. HD-8-S
  6. Operator's & parts manual

Shaver HD-8-S Operator's & Parts Manual

Hydraulic post driver
Hide thumbs
Table of Contents

Advertisement

Quick Links

Operators & Parts
Manual
Hydraulic
Post Driver
Models HD-8-S, HD-8-H-S,
HD-10-S, HD-10-H-S,
HD-12-H-S & SHD-10
Safety
Operation
Maintenance
Repair
Troubleshooting
Parts
HD8/10/12OPMAN (a) 5/18
Shaver Manufacturing Company
103 South Washington Avenue, Graettinger, Iowa 51342
Phone: (712) 859-3293 — Fax: (712) 859-3294 — www.shavermfg.com
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HD-8-S and is the answer not in the manual?

Questions and answers

Related Manuals for Shaver HD-8-S

Summary of Contents for Shaver HD-8-S

  • Page 1 Operators & Parts Manual Hydraulic Post Driver Models HD-8-S, HD-8-H-S, HD-10-S, HD-10-H-S, HD-12-H-S & SHD-10 Safety Operation Maintenance Repair Troubleshooting Parts HD8/10/12OPMAN (a) 5/18 Shaver Manufacturing Company 103 South Washington Avenue, Graettinger, Iowa 51342 Phone: (712) 859-3293 — Fax: (712) 859-3294 — www.shavermfg.com...

  • Page 2: Table Of Contents

    Service Procedures ........32 Contents Dismounting Post Driver from Base Plate.32 Safety ............3 Post Driver Disassembly ......33 General ............4 Seal Replacement ........34 Safety Alert Symbols ........4 Spring Replacement ........ 34 Safety Icon Nomenclature ......5 Guide Block/Roller Replacement .....

  • Page 3: Safety

    An accident can often b e avoided by recognizing potentially hazardous situations before an accident occurs. As you assemble and operate the Shaver Post Driver, you must be alert to potential hazards. You should also have the necessary training, skills, and tools to perform this assembly procedure.

  • Page 4: General

    Indicates an imminently hazardous situation damaged, please contact your dealer or which, if not avoided, will result in death or serious injury. This signal word is limited to the Shaver Manufacturing Company most extreme situations . 103 South Washington Avenue P.O. Box 358...

  • Page 5: Safety Icon Nomenclature

    Safety Icon Nomenclature Read the manual Eye protection Foot protection Hand protection Hearing protection Inspect equipment Two-person operation Warning decal alert Bending hazard (hydraulic hose) Crushing hazard Crushing hazard (hand) Do not weld Electrocution hazard Explosion hazard High-pressure fluid hazard Impact hazard (hydraulic hose) Pressurized fluid Projectile hazard (body)

  • Page 6: Safety Warnings

    Post Driver. While transporting, applicable manuals. Contact Shaver never ride on or permit others to ride on the Manufacturing Company if Post Driver. instructions provided are unclear or understood.

  • Page 7: Hydraulic Hoses

    WARNING WARNING Do not drop heavy objects on Potential pinch points. hoses. A sharp impact may cause Keep hands clear of Post internal damage to the hose. Driver while operating. Applying pressure to a damaged Never place hand(s) on hose may cause it to rupture, resulting in top o f a post when inserting it into the Post personal injury.

  • Page 8: Introduction

    Shaver the largest selling Post Driver in the country. The Shaver HD-8-S & HD-10-S (manual tilt adjustment) and HD-8-H-S, HD-10-H-S, SHD- 10, & HD-12-H-S (hydraulic tilt adjustment) Hydraulic Post Drivers are a durable piece of equipment that, with regular maintenance, will provide many years of service.

  • Page 9: Specifications

    Specifications HD-8-S & HD-8-H-S HD-10-S & HD-10-H-S DESCRIPTION 88 in (223.5 cm) collapsed 100 in (254 cm) collapsed Approximate Height 133 in (337.8 cm) extended 148 in (376 cm) extended 30 in (76.2 cm) 44 in (111.8 cm) Approximate Width 28 in (71.1 cm)

  • Page 10: Safety Sign Locations

    Safety Sign Locations Driver Safety Signs and Informational Labels Item Part Number Description MS-183 Decal, Danger Instructions MS-165 Decal, Danger Safety Arm Attachment MS-163 Decal, Warning Pinch Point MS-181 Decal, Warning Pinch Point MS-171 Decal, Warning High Pressure Hydraulics MS-106 Decal, Important Valve Instructions MS-166 Decal, Important Leave Arm Open...

  • Page 11: Safety Signs

    2. MS-165 – Decal, Danger Safety Arm Attachment Safety Signs 1. MS-183 – Decal, Danger Instructions 3. MS-163 – Decal, Warning Pinch Point 4. MS-181 – Decal, Warning Pinch Point 5. MS-171 – Warning High Pressure Hydraulics Decal 6. MS-106 – Decal, Important Valve Instructions...
  • Page 12 7. MS-166 – Decal, Important Leave Arm Open 8. SM-0011-ST –Tag, Caution Springs 9. MS-180 – Decal, Cylinder Nut 10. Decal, Warranty Void, Roadlock...

  • Page 13: Assembly Procedure

    Assembly - General Assembly Procedure Unpacking NOTE: Refer to the Service Parts section of this manual for an illustration and description of all the WARNING parts. The Main Carriage Channel has provisions for Due to the size and weight of the mounting the Base Plate (Manual or Hydraulic) in Post Driver, two people are required two positions.

  • Page 14: Mounting Instructions

    Main Carriage Channel Mounting Instructions Front-Mounted 4. Use a suitable overhead lifting device (arrow as shown) to raise (stand up) Main 1. Attach the Mounting Bracket(s) to the Carriage Channel. Position the Driver in front front of the tractor with the bolts provided. of the Base Plate as shown below.

  • Page 15: Mounting Instructions

    5. Align the bushings in the Driver with the bushings in the Base Plate (see arrows below). Install Pins and secure with the supplied cotter pins. ‘X’ Storage leg heights on 3-point hitch mount. Mounting Instructions Rear-Mounted (3-Point Hitch) 1. Place three-point hitch weldment upside down on the floor.

  • Page 16: Base Plate

    the Universal Mounting Bracket with two (2) each 1/2" bolt, lock washer and nut (items 9, 10, & 11). Attach the Pump/Motor/Reservoir (item 2) by lining up the slots in the IMPORTANT NOTICE Pump/Motor/Reservoir with slots in the Universal Mounting Bracket The following hydraulic fittings and hoses Reservoir Bracket, then secure four (4) each...

  • Page 17: Attaching Driver To Base Plate

    NOTE: Hydraulic base plate installation is shown. Installation of manual base plate is similar. Main Carriage Channel Assembly is tall and heavy. To avoid 1. Remove the carriage bolts, washers, and tip over, resulting in serious injury nuts from hydraulic base plate. Save the or death, leave the overhead lifting hardware for reuse.

  • Page 18: Connection To Hydraulic Supply

    first position and align Driver with lower base Plate plate pivot location (A below), then install mounting pin. Adjust forward tilt crank and side tilt crank to align upper mounting pin holes (B below), then install upper mounting pin. Secure pins with included cotter pins. Manual Tilt Base Control Valve (see parts chart below).

  • Page 19: Triple Lever Control Valve For Hydraulic Base Plate

    Ensure the oil is clean and properly filtered before connecting the Post Driver to a hydraulic power source. Failure to follow oil cleanliness standards voids the Shaver Post Driver warranty. Triple Lever Control Valve for Hydraulic Base Plate 1. Remove the plugs from the hydraulic control valve.
  • Page 20 Triple Lever Control Valve for Hydraulic Base Plate Parts List Item Qty. Part No. Description 2. Install the hydraulic valve (item 2) on Valve Bracket (item 2) using three (3) 5/16-18 x 2- SM-003-PVBP Plate, Valve Bracket VP-03 1/2” valve mounting bolts, washers, and nuts. Valve –...

  • Page 21: Rubber Debris Guard

    hose is screwed into the 90° fitting from the ‘OUT’ port of the valve using paste-type thread sealant on the fittings. 8. Attach the tilt cylinder hoses as follows (see chart & illustration on the left). Attach the other end of the hose connected to the rod end of the side tilt cylinder (item 6a) to the 45°...

  • Page 22: Safety Arm Assembly

    UPPER LOWER SHD-10 Rubber Debris Guard mounting. 3. For SHD-10 attach the Rubber Guard and Caution Tag on drive ram, with guard mounting hardware, three (3) 3/16” x 3/8 blind rivets, as shown above. Safety Arm Mounting holes (HD-10 with manual base plate shown).
  • Page 23 6. Install the Swing Arm A ssembly. a. Apply a light film of good quality grease to the pivot shaft on Swing Assembly. b. Slide the pivot shaft into the tube on the Safety Arm Mounting Bracket and secure with cotter pin as shown above. c.

  • Page 24: Document Storage Tube

    Attachments and Options Assembly Document Storage Tube Steel Post Holder Accessory Manual Storage Tube & mounting rivets. 1. If desired, locate the document storage tube in a convenient location on the Post Steel Post Holders for HD-8 shown. Steel T-Post Holder on Driver.

  • Page 25: Post Driver Operation

    5. All Post Driver safety equipment must be inspected, maintained, kept in working order, and used during Post Driver operation. 6. Do not place your hand(s) on top of the post when placing the post in the Post Driver or while the Post Driver is operating.

  • Page 26: Self-Contained Mounting

    3. Attach the three-point top link to removable pin (‘B’ below) and secure with cotter pin. NOTE: Adjust the length of the machine’s top link, as required, to correctly attach the Post Drivers 3-Point Mounting Bracket. Pressure Hose Return Hose Control Valve Control Valve, Hydraulic Pressure Hose, and Hydraulic Return Hose.

  • Page 27: Preparing To Drive A Post

    quick attach bracket equipped unit toward PARK. the Post Driver until the plates line up. Lift the Driver off the ground and lock with the skid loader locking arms. Drive Ram, Stabilizer, & Storage Legs. IMPORTANT: When operating the Ram (‘A’ above) to drive in posts, the Stabilizer (‘B’...
  • Page 28 IMPORTANT NOTICE Do not use grease on the guide blocks or in the main carriage channel. Grease will retain abrasive material, which will result in premature wear. Guide Block/Roller locations (arrows) on Driver (HD-10 shown with transparent Main Carriage).
  • Page 29 3. Pull up Safety Latch and push Main Hydraulic Control Lever to lower Drive Ram. To avoid personal injury or death, do not operate the Post Driver by yourself. Always have another person to control the machine or power source. NOTE: For operation of valve control levers refer to the illustration below.
  • Page 30 NOTE: There should be a 1” to 2” gap between the top of the fence post and the bottom of the drive ram hammer plate. Potential Pinch Points. Never drive a fence post without the guard Keep hands clear of Post in place.
  • Page 31 6. Do not stand in front of the drive ram while operating the Post Driver. Stand at a 45-degree angle to the side of the Post 7. To drive the fence post straight, adjust the main carriage channel side-to-side and fore- and-aft using manual cranks (manual base plate) or second and third hydraulic control valve levers (hydraulic base plate).
  • Page 32 8. Pull up Safety Latch and pull back Main Hydraulic Control Lever to raise Drive Ram. Drive Ram, Hydraulic Control Valve Lever, & Safety Lever. 9. Hold up Safety Latch and push Main Hydraulic Control Lever to release the Drive Ram and create impact with post.
  • Page 33 IMPORTANT NOTICE Posts will drive into the ground much straighter using shorter strokes. Use caution when driving small diameter wood steel posts. Maximum impact is not necessary with these smaller diameter posts cause damage (splintering or breakage) of posts. NOTE: If the post stops going down or is crooked after a few impacts, stop and move the post to a different location.
  • Page 34 Contact Shaver Manufacturing Company if any of the Cylinder Scissor Stop Bolt. instructions provided are unclear or not understood. Proper care your NOTE: Failure to tighten this bolt could responsibility.

  • Page 35: Dismounting Post Driver

    associated repairs must be performed with the 4. Remove cotter pins and two ( 2 ) B a s e main carriage channel and drives ram in a P l a t e P i n s ( ‘ A ’ a b o v e ) that horizontal position, such as on a suitable...
  • Page 36 There can be tension remaining on spring. As the bolt is removed, the spring will quickly retract (compress) away from upper spring bracket. 5. Remove the retaining strap (HD-8/HD-10) and remove the Upper Spring Bracket (HD- 10/HD-12). 6. Remove the Upper Cylinder Rod Self- Locking Nut (‘D’...

  • Page 37: Seal Replacement

    8. Replace the Cylinder Cap & Piston Rod into Seal Replacement the Cylinder Tube. Use a paste type thread NOTE: Follow the disassembly instructions sealer, DO NOTE USE A TAPE SEALER as for the Post Driver until the Cylinder is out this will void the Cylinders warranty.

  • Page 38: Guide Block/Roller Replacement

    HD-12 Springs. NOTE: On an HD-12 Post Driver Spring replacement done without removing the Cylinder. 1. Remove the 1/2” bolt and lock washer from bottom of both springs. 2. Then remove the 1/2” bolt and lock washer from top of both springs. 3.
  • Page 39 Sleeves as shown below. Thread the below)). Tighten the nut just enough to fully bolts into Lower Spring Clip just enough engage the threads, as shown below. to fully engage the bolt threads. 10. HD-8/HD-10 attach Springs to Upper Spring Bracket.
  • Page 40 a. Get assistance and use a suitable round pry bar to engage one set of 14. Pull Main Carriage Channel down holes in both the bracket and drive ram install Road Lock Pin (‘I’ below) and Lynch yoke. Pry the bracket forward until the Pin in upper hole in Drive Ram.
  • Page 41 Main Carriage Channel Forward and Side Tilt Cylinder Assembly is tall and heavy. To avoid Seal Replacement tip over, resulting in serious injury or death, leave the overhead lifting WARNING device attached Main Carriage Channel while assembling Removing tilt cylinder(s) from the components.

  • Page 42: Storage

    1. Before storing, remove debris and clean the entire unit with compressed air or pressure washer. 2. Inspect the Shaver Post Driver. Replace any worn or damaged parts before using the Post Driver again. • Check all bolted connections. Ensure that fasteners are tight, and all pins are secured in place.

  • Page 43: Troubleshooting

    Troubleshooting Troubleshooting Chart Problem Possible Cause Remedy Drive Ram will not move or Slide Guide Blocks/Rollers lack lubrication Lubricate with clean engine oil or spray freely in Main Carriage Channel. lubricant. Guide Blocks/Rollers installed Refer to Service Information section incorrectly. assembly procedures for correct orientation.

  • Page 44: Service Parts

    Service Parts Driver Assembly SM-0011S-DRC - Ram Assembly, HD-8 Driver Stabilized SM-1011S-DRC - Ram Assembly, HD-10 Driver Stabilized (SHOWN) SM-1012S-DRC - Ram Assembly, SHD-10 Driver Springless...

  • Page 45: Ram

    Driver Assembly SM-0011S-DRC - Ram Assembly, HD-8 Driver Stabilized SM-1011S-DRC - Ram Assembly, HD-10 Driver Stabilized (SHOWN) SM-1012S-DRC - Ram Assembly, SHD-10 Driver Springless Qty. Qty. Qty. Part No. Description Item SM-0011S-DRC SM-1011S-DRC SM-1012S-DRC HD-8 HD-10 (Shown) SHD-10 Springless SM-0011-DRO Ram Assembly, Driving, Only, HD-8 SM-1011-DRO Ram Assembly, Driving, Only, HD-10 (Shown)
  • Page 46 *When replacing Blocks/Rollers use all the same type. Service Parts Driver Assembly SM-1211S-DRC - Ram Assembly, HD-12 Driver Stabilized...
  • Page 47 Driver Assembly SM-1211S-DRC - Ram Assembly, HD-12 Driver Stabilize Qty. Part No. Description Item SM-1211-DRO Ram Assembly, Driving, Only, HD-12 SM-12412S Carriage Assembly, HD-12 Stabilized SM-1211-DRSA Spring Assembly, HD-12 SM-1211-SBU Bracket, Upper, HD-12 Spring SM-1026-S Cylinder Assembly, Complete HD-10/12 SM-10267 Locknut, Piston, 1-8 Nylon SM-00512R Block, Nyrim...

  • Page 48: Driver Assembly- Springs

    Driver Assembly – Springs SM-0011-SA - Spring Assembly, HD-8 SM-1011-SA - Spring Assembly, HD-10 (Shown) Qty. Qty. Part No. Description Item SM-0263-S SM-1011-SA HD-8 HD-10 SM-0011-SBL Bracket, Lower Spring, HD-8 SM-1011-SBL Bracket, Lower Spring, HD-10 (Shown) SM-0011-SC Clip, Spring, HD-8 SM-1011-SC Clip, Spring, HD-10 (Shown) SM-0011-DRSO...
  • Page 49 Driver Assembly – HD-12 Springs SM-1211-DRS - Spring Assembly, HD-12 Qty. Part No. Description Item SM-1211-DRSA Spring Assembly, HD-12 SD-101-B2 Bushing, 1-7/8 OD x 5/8 ID x 2 L 300101 Washer, Lock 1/2" Zn 300132 Screw, Cap 1/2-13 x 2 Hex Head Gr5 Zn Full Thread 300137 Bolt, Tap 1/2-13 x 4-1/2 Hex Head Gr5 Zn Full Thread SM-1211-DRSA - Spring Assembly, HD-12...
  • Page 50 Driver Assembly – HD-12 Springs SM-1211-SBU – Upper Spring Bracket, HD-12 Qty. Part No. Description Item SM-1211-SC Clip, Spring, HD-12 300101 Washer, Lock 1/2" Zn 300132 Screw, Cap 1/2-13 x 2 Hex Head Gr5 Zn Full Thread SM-1211-SBL – Lower Spring Bracket, HD-12 Qty.
  • Page 51 Driver Assembly – Road Lock Plate Assemblies & Cushions SM-0041-RLB – Plate Assembly, Road Lock, HD-8 SM-1041-RLB – Plate Assembly, Road Lock, HD-10 (Shown) & SHD-10 SM-1241-RLB – Plate Assembly, Road Lock, HD-12 Qty. Qty. Qty. Part No. Description Item SM-0041-RLB SM-1041-RLB SM-1241-RLB...

  • Page 52: Rubber Guard Assembly

    Rubber Guard Assembly SM-1211-G – Rubber Guard Kit HD-8/10/12 Qty. Part No. Description Item SM-1211-G3 Shield, Rubber 6” x 14-3/4” SM-0011-ST Tag, Caution Springs 300145 Nut, Hex 1/4-20 Zn 300147 Washer, Lock 1/4 Zn 300149 Bolt, Carriage 1/4-20 x 1 Gr2 Zn SM-1212-GS –...

  • Page 53: Safety Arm Assembly

    Safety Arm Assembly SM-0011-SAA - Safety Arm Assembly Qty. Part No. Description Item 300106 Pin, Cotter 3/16 x 2-1/2 300148 Pin, Roll 1/4 x 1-1/2 300167 Nut, Lock 3/4-10 Nylon Hex Zn 300172 Bolt, Tap 3/4-10 x 2 Hex Head Gr5 Zn 300213 Washer, Flat 5/8 300221...

  • Page 54: Manual Base Plate Assembly

    Manual Base Plate Assembly HD-8 & HD-10 Manual Base Plate Qty. Part No. Description Item SM-1015 Base-Plate Weldment, HD-10 SM-015-CC Cover, Crank, HD-8/10 SM-016 Crank Assembly, Side Tilt (includes SM-015-CC) SM-017 Sleeve, Side Tilt Crank SM-018 Nut, 3/4-10 Side Tilt Crank SM-019 Crank Assembly, End Tilt (includes SM-015-CC) SM-021...

  • Page 55: Hydraulic Base Plate Assembly

    Hydraulic Base Plate Assembly HD-8 & HD-10 Hydraulic Base Plate Qty. Part No. Description Item HBP-91011 HD-10 Hydraulic Base Plate Assembly (Includes mounting hardware) HBP-91012 Plate Weldment, Base, Hyd. HBP-90296 Cylinder, Hyd. Forward Tilt HBP-90296-SK Seal Kit, 2” Tilt Cylinder (Not Shown) HBP-90297 Cylinder, Hyd.

  • Page 56: Hd-8/Hd-10 Hydraulic Base Plate

    Hydraulic Base Plate Assembly HD-12 & SHD-10 Hydraulic Base Plate Qty. Part No. Description Item HBP-912111 HD-12 Hydraulic Base Plate Assembly (Includes mounting hardware) HBP-912115 Plate Weldment, Base, Hyd. HD-10 HBP-91217 Cylinder, Hyd. Forward Tilt HBP-912177 Seal Kit, 2-1/2” Tilt Cylinder (Not Shown) HBP-91218 Cylinder, Hyd.
  • Page 57 Manual Base Plate Valve & Hose Assembly Qty. Part No. Description Item VP-01-SP Valve – 1 Spool SM-001-PVBP Plate, Prince Valve Bracket Adapter, 90° SAE #12MORB – 3/4FNPT SC-50-H52 Adapter, 90° SAE #12MORB – 1/2NPTSM CTP-69011208 Adapter, 45° SAE #10MORB – 3/4FNPT F-6902-10-12 SM-025-R Hose Assembly, Hyd.
  • Page 58 Hydraulic Base Plate Valve & Hose Assembly Qty. Part No. Description Item Valve – 3 Spool VP-03-SP SM-003-PVBP Plate, Valve Bracket V-03 Adapter, 90° SAE #12MORB – 3/4FNPT SC-50-H52 Adapter, 90° SAE #12MORB – 1/2NPTSM CTP-69011208 Adapter, 45° SAE #10MORB – 3/4FNPT F-6902-10-12 Adapter, Straight SAE #10MORB –...

  • Page 59: 3-Point Hitch Assembly

    3-Point Hitch Assembly MB-01-A - Bracket Assembly, CAT-I & II 3-Point Mounting w/Stands Part No. Description Item MB-01-AA Bracket Weldment, 3-Point Mounting CAT-3 MB-01A-12 Bushing (for CAT-II) SM-1041-RLP Pin, Road Lock (included in MB-01-AA) OS-4-22SFA Leg Weldment, Storage 300106 Pin, Cotter 3/16 x 2-1/2 (included in MB-01-AA) 300218 Screw, Cap 5/8-11 x 1-3/4 Hex Head Gr5 Zn (included in MB-01-AA) MB-1201-A - Bracket Assembly, CAT-II 3-Point Mounting w/Stands (HD-10/HD-12/SHD-10)
  • Page 60 3-Point Hitch Assembly MB-1301-A - Bracket Assembly, CAT-III 3-Point Mounting w/Stands (HD-10/HD-12/SHD-10) Part No. Description Item MB-1301-AA Bracket Weldment, 3-Point Mounting CAT-3 OS-4-22SFA Leg Weldment, Storage Stand MB-1201A-12 Pin, Top 3-Point 300106 Pin, Cotter 3/16 x 2-1/2 300218 Screw, Cap 5/8-11 x 1-3/4 Hex Head Gr5 Zn (included in MB-1301-AA) OS-4-22 - Stand Package, Manual (Old Style) Part No.

  • Page 61: Skid Loader Mounting Assembly

    Skid Steer/Loader Mounting Assembly MBS-77-10 - Bracket Assembly, Universal Mounting Part No. Description Item MBS-77-10AA Bracket Weldment., Driver Skid Loader OS-4-22SFA Leg Weldment, Storage Stand 300218 Screw, Cap 5/8-11 x 1-3/4 Hex Head Gr5 Zn (included in MBS-77-20AA) MBS-77-20 - Bracket Assembly, Universal Mounting (for OH-200) Part No.

  • Page 62: Hydraulic Control Valves

    Hydraulic Control Valves Single & Multiple Control Lever Valves VP-01-SP Valve – 1-Spool VP-03-SP Valve – 3-Spool Qty. Qty. Part No. Description Item VP-01-SP VP-03-SP VP-ARVC Valve, Main Relief, Direct Acting 1800-3000 PSI (set at 2538 PSI) VP-SCK Spring Kit, Centering VP-LSHK Handle Kit, Locking Safety VP-LSHO...

  • Page 63: Self-Contained Hydraulics

    Self-Contained Hydraulics OH-200 - Self-Contained Mounting Package Complete Part No. Description Item MBS-77-20 Bracket Assy., Universal Mtg. OH-101 Self-Contained Mtg. Pkg. Less Bracket. OH-101 - Self-Contained Mounting Package Less Bracket Qty. Part No. Description Item OH-101-2B Frame Weldment, Reservoir Bracket. OH-101-1 Self-Contained Mtg.

  • Page 64: Pump/ Motor Kit

    Self-Contained Hydraulics OH-101-1 – Pump/Motor Kit, Part No. Description Item 700109 Adaptor, 90° SAE#16MJIC- 1” MNPT 700110 Adaptor, Straight SAE#16MORB- #8FORB 700111 Adaptor, 90° SAE#16MJIC- #20MORB 700112 Adaptor, 45° SAE#8MORB- 1/2” FNPT CT-FC10 Valve, Check, SAE #10 Inline OH-101-1F2 Cap, Breather OH-101-1H Hose Assy., Hyd.

  • Page 65: Driver Cylinder Assembly

    Driver Cylinder Assembly SM-0263-S - Cylinder Assembly, Complete HD-8 SM-1026-S - Cylinder Assembly, Complete HD-10/12 (Shown) & SHD-10 Item Qty. Qty. Part No. Description SM-0263-S SM-1026-S HD-8 HD-10/12 300111 Screw, HSSS 5/16-18 x 5/16 S-0269 Nut, 1/2 F. Piston Guide, HD-8/10 SM-0936C Nut, Cylinder Coarse Machine SM-018...

  • Page 66: Attachments-Pilot Augers

    Attachments – Pilot Augers SM-1001-PA4 – Auger Assembly, 4” Pilot (HD-10) & SM-1001-PA6 – Auger Assembly, 6” Pilot (HD-10/SHD-10) (Shown) SM-1201-PA4 – Auger Assembly, 4” Pilot (HD-12) & SM-1201-PA6 – Auger Assembly, 6” Pilot (HD-12) HD-10 & SHD-10 HD-12 Item Qty.

  • Page 67: 6" Auger Fish Tail & Tooth Assembly

    Attachments – Pilot Augers 6” Auger Fish Tail & Tooth Assembly Qty. Part No. Description Item SA-304-PF Auger Point Fish Tail SA-6230 Auger Teeth 300236 Screw, Cap 1/2-13 x 3 Hex Head Gr2 Zn 300326 Screw, Cap 1/2-13 x 2 Hex Head Gr5 Zn 300101 Washer, Lock 1/2 Zn 300102...

  • Page 68: Motor & Hose Assembly

    Attachments – Pilot Augers SM-1011-PA – Motor & Hose Assembly Qty. Part No. Description Item SM-1011-PAHM Motor, Hydraulic F-1501-08 Fitting, 90° SM-0234-R Hose Assy., Hyd. 1/2" x 120” 8MXMS 100R2 SD-510-83 Fitting, Swivel 700112 Adapter, 45° SAE #8 MORB-1/2” FNPT SC-2550-C Fitting, 90°...
  • Page 69 Attachments – Hydraulic SM-SL-HRSK – Return Kit, Split, Skid Loader Qty. Part No. Description Item V-SLR Valve Assembly, Skid Loader Return SM-SLR-HR Hose Assembly, Return, 3/4” x 23” SM-SLR-HCD Hose Assembly, Case Drain, 3/4” x 23” 700120 Coupler, Quick Female 3/8 NPT Flat Face CT-832-FC Coupler, Quick Female 1/2 NPT Flat Face CT-832-MC...

  • Page 70: Attachments-Steel Post Holders

    Attachments – Steel Post Holders Part No. Part No. Part No. Description Item HD-8 (Shown) HD-10 HD-12 SM-0011-PH SM-1011-PH SM-1211-PH Steel Post Holder SM-0011-PHSQ SM-1011-PHSQ SM-1211-PHSQ Square Steel Post Holder Attachments – Stabilizer Extensions SM-0016 - HD-8 Stabilizer Extension SM-1016 - HD-10/SHD-10 Stabilizer Extension (Shown) SM-1216 - HD-12 Stabilizer Extension Qty.

  • Page 71: Replacement Decals

    Decal, Important Valve Instructions MS-166 Decal, Important Leave Arm Open SM-0011-ST Tag, Caution Springs MS-180 Decal, Cylinder Nut MS-200D Decal, Shaver Logo Large MS-280 Decal, FEMA Member Large MS-USA Decal, Made in the USA w/Flag MS-220 Paint, Black Spray MS-230...
  • Page 72 If the part needs to be returned, Shaver will arrange return by a call tag or by freight. If warranty credit is due, back freight will also be paid in reimbursement.
  • Page 73 Product model number Please make a copy of this WARRANTY REGISTRATION form for your records and return the original. This form must be completed and returned to Shaver within 30 days from receipt of delivery or warranty may become void.
  • Page 74 Notes __________________________________________________________ __________________________________________________________ __________________________________________________________ __________________________________________________________ __________________________________________________________ __________________________________________________________ __________________________________________________________ __________________________________________________________ __________________________________________________________ __________________________________________________________ __________________________________________________________ __________________________________________________________ __________________________________________________________ __________________________________________________________ __________________________________________________________ __________________________________________________________ __________________________________________________________ __________________________________________________________ __________________________________________________________ __________________________________________________________ __________________________________________________________ __________________________________________________________ __________________________________________________________ __________________________________________________________ __________________________________________________________ __________________________________________________________ __________________________________________________________ Shaver Manufacturing Company www.shavermfg.com 712-859-329...
  • Page 75 Notes __________________________________________________________ __________________________________________________________ __________________________________________________________ __________________________________________________________ __________________________________________________________ __________________________________________________________ __________________________________________________________ __________________________________________________________ __________________________________________________________ __________________________________________________________ __________________________________________________________ __________________________________________________________ __________________________________________________________ __________________________________________________________ __________________________________________________________ __________________________________________________________ __________________________________________________________ __________________________________________________________ __________________________________________________________ __________________________________________________________ __________________________________________________________ __________________________________________________________ __________________________________________________________ __________________________________________________________ __________________________________________________________ __________________________________________________________ __________________________________________________________ Shaver Manufacturing Company www.shavermfg.com 712-859-329...
  • Page 76 Shaver Manufacturing Company P.O. Box 385, Graettinger, IA 51342 Phone: 712-589-3293 Fax: 712-589-3294 Website: www.shavermfg.com E-mail: sales@shavermfg.com www.FarmEquip.org Shaver Post Driver™ September 2018 Shaver Manufacturing Company www.shavermfg.com 712-859-329...

This manual is also suitable for:

Hd-8-h-sHd-10-sHd-10-h-sHd-12-h-sShd-10

Table of Contents

Save PDF