U-tec Ultraloq U-Bolt Pro Manual

Important Notes

• Do not use a power drill for installation.
• Install and test the lock with the door open to avoid being locked out.
• Please read all the instructions before contacting customer support.
• Please contact customer support before returning the product to the store.
• DO NOT install the batteries before installing the lock!
• Follow the instructions in sequential order!
• This lock is designed for the following operating temperatures:
  Outside Lock Body: -31°F(-35°C) to 158°F (70°C)
  Inside Lock Body: 14°F (-10°C) to 131°F (55°C)
• Please must use AA Alkaline Battery and don't use Lithium Battery or Rechargeable Battery.

Statements

To ensure the best service, please register your account at www.u-tec.com/register.html

Ultraloq Terms & Policies

Before using all Ultraloq products, please read all applicable terms, rules, policies and usage provisions found at www.u-tec.com/company/privacy. By using your Ultraloq, you agree to be bound by the U-tec Privacy Policy.

Need Help?
For technical documents and more
Please visit www.u-tec.com/support
Email: support@u-tec.com

Packing List

Interior Assembly

Exterior Assembly

Interior Assembly Mounting Plate

Strike

Bolt

Backup Key

Screw A

Screw B

Screw C

Screw D

Screw E

AA Alkaline Batteries
(May not be included for some regions)

Screwdriver

User Guide

Drill Template

Reset Needle

Bridge
(Optional)

Installation Guide

Installation Video

Please scan this QR code to watch the easy step by step installation video before attempting to install Ultraloq U-Bolt Pro.
Or you can also view the webiste directly. www.u-tec.com/lock/U-bolt_pro/guide

1. Preparing Door
   Check the door's dimensions.
   Step 1
   Measure to confirm that the door is between 1⁵/₁₆"~ 2 " (33 mm-50 mm) thick.
   Step 2
   Measure to confirm that the diameter of the hole is 2 ¹/₈ " (53 mm).
   Step 3
   Measure to confirm that the backset is either 2 ³/₈ " or 2 ³/₄" (60 mm or 70 mm).
   Step 4
   Measure to confirm that the diameter of the hole in the door edge is 1" (25 mm).
   Step 5
   Measure to confirm the depth of the hole in the frame is less than 1''(25mm).
   
   If you have a new door, please drill the holes according to Drill Template.
2. Installing Bolt and Strike
   Step 1
   Install Bolt into the door. Make sure the UP ↑ icon goes up.
   Note: Bolt is set for 2 ³/₈" backset initially. It can be adjusted to 2 ³/₄" if needed.
   Step 2
   Install Strike into the door frame.
   
3. Installing Exterior Assembly
   Step 1
   Carefully break off cylinder tailpiece at required mark for your door thickness.
   
   
   Use two pairs of pliers as shown or tailpiece will be damaged.
   
   After installing the cover plate, there should be 1 or 2 pieces over the Assembly Mounting Plate hole.
   Step 2
   Keep Bolt retracted and the cylinder tailpiece horizontal. Install Exterior Assembly. Please do not insert the mechanical key.
   Step 3
   Align its two sticks with two holes on Bolt. The cable goes through the hole below Bolt.
   
4. Installing Interior Assembly Mounting Plate
   Step 1
   Route the cable through the hole on Interior Assembly Mounting Plate.
   Step 2
   Secure Interior Assembly Mounting Plate to Exterior Assembly using Screws D.
   
5. Installing Interior Assembly
   Step 1
   Remove the battery cover of the Interior Assembly.
   Step 2
   Insert the connector of the cable to the socket on Interior Assembly. Press the connector in firmly until it is completed seated.
   
   Step 3
   Rotate the knob and keep it in a vertical position to stay unlocked.
   
   Step 4
   Attach Interior Assembly to Mounting Plate and tighten 2 Screws E.
   
6. Installing the Batteries and Performing the Door Handing Process
   This step will teach your lock the orientation of your door and is crucial to lock operation.
   Step 1
   Rotate the knob and keep it in a horizontal position to stay locked.
   
   Step 2
   Insert 4 AA Alkaline Batteries.
   
   Note: Any fingerprint or code can unlock U-Bolt Pro in Factory Default Mode.
   Step 3
   After a few seconds, Bolt will retract and extend on its own to learn the orientation of the door. This is called the door handing process, and it is crucial to lock operation.
   Step 4
   Install battery cover.

User Guide Video

Please watch our easy step by step User Guide video before attempting to use your Ultraloq U-Bolt Pro Smart Lock.

Or you can also view the webiste directly. www.u-tec.com/lock/U-bolt_pro/guide

Product Overview

Exterior

Anti-peep Keypad
Used to enter the code and unlock from outside.
Advanced Fingerprint Reader
Used to verify your finger and unlock from the outside.
Backup Key Hole
Used to insert the key to unlock in emergency situations.
Micro USB (5V)
Used to connect power bank to activate the lock when battery runs out.
Tri-color LED Indicator
Shows you authorized or denied access, Bluetooth connectivity status, battery status etc.
Ultraloq Button
Used to lock from the outside, illuminate the keypad for code entry and confirm previous operation etc.

Interior

Reset Button
Used to reset the lock to Factory Default settings. If the lock was paired to App, please must click "Delete" to remove the device from App.
Battery Compartments
Used to insert 4 AA alkaline batteries.

Note: Lithium batteries may have a longer life, but when they begin to fail, they fail quickly. We don't recommend them because they don't give you a lot of time to change your batteries before the lock is completely dead. Please don't use any Rechargeable Battery.

Battery Cover
Used to cover batteries and product label.
Knob
Used to unlock and lock the door from inside. LED Indicator Turns red when door is unlocked.

Low Battery Alarm

There will be low battery alert on the lock and App when battery is low. Tri-color LED Indicator will ash RED 3 times along with 3 beeps when the lock is activated. Please replace batteries.

Lock Setup

Scan QR code to download the App

Step 1
Scan above QR code to download the App, or search "U-tec"in App Store (iOS) and Google Play (Android).
Step 2
Open the App, register U-tec account and log in the account.
Step 3
Make sure the lock is in Factory Default Mode. Turn on Bluetooth on your smartphone, stay near the lock (within 10 feet / 3 meters) and search the lock in the App.
Step 4
Pair the lock in the App and start to use it.

Note: Please refer to the guide in U-tec App for more information.

DON'T WANT TO USE THE APP?
Please go to programming guide for Standalone Mode.

Using Your Lock

Unlock From Outside

• User Code
  Enter 4-8 digit code and press Ultraloq Button to unlock.
  Note: You can press Ultraloq Button to turn on Keypad backlight.
  
• Fingerprint
  Place your finger on Fingerprint Reader to unlock.
  
• Smartphone
  Use your smartphone to unlock. Please refer to the guide in U-tec App.
  

Lock From Outside

Press Ultraloq Button to lock manually. Enable Auto Lock feature and the lock will relock automatically.

Unlock From Inside

Rotate the knob to a vertical position to unlock.

Reset the Lock

Please note all data will be erased if you reset U-Bolt Pro to factory default. If you are using U-tec App as Owner, please click "Delete and Reset" to remove the lock from your U-tec Account, then use a Reset Needle to push the Reset Button (at the bottom of Interior Assembly) for around 3 seconds until you hear one long beep and two short beeps.

Replace Batteries

Please use 4 high-quality alkaline AA batteries for replacement when the battery is dead.

5V Emergency Power

Micro USB interface is used to connect regular 5V power bank to activate the lock in case the battery is dead.

Emergency Key Override

Emergency Key Override can be used when the battery is dead. Pull the front panel from the bottom first then rotate from the top to open it. You can see Backup Key Hole inside. Insert the key and rotate to unlock, just like any lock.

1. Pull
   
2. Rotate
   
3. Insert
   

Important Note
Please keep at least one key in secure location outside of your place.

Enable Or Disable Auto Lock

Enable
Please keep Bolt unlocked and press "1" button for 3 seconds until LED turns green and "1" button blinks.
Disable
Please keep Bolt unlocked and press "0" button for 3 seconds until LED turns green and "0" button blinks. This can also be set in U-tec App and Auto Lock timing can be programmed between 10 seconds to 5 minutes. Factory Default timing is 30 seconds.

Anti-peep Keypad

The lock supports up to 16-digit Vague Code. Just enter any 16-digit code, as long as a correct code is included in what you entered, you can open the door.

Place Finger

1. Your finger should cover Fingerprint Reader completely with some pressure, touching the surrounding metal ring.
2. Make sure that your finger and Fingerprint Reader are clean and dry. For Fingerprint Reader, use a clean, lint-free cloth to wipe off any dirt or debris.
3. Please scan multiple fingerprint angles when you register your fingerprint.
4. While scanning your finger, you shouldn't tap too quickly or move your finger around.
5. If you have trouble enrolling one finger, try another.
6. U-Bolt Pro fingerprint sensor has self-study function which the verification rate will be improved after multiple success.

Standalone Mode Programming Guide

It is recommended to use U-tec App to program your lock. If you don't have a smartphone or don't want to use the App, you can use the programming instructions below.

Standalone Mode is NOT available after the lock is registered in App! Please reset the lock to Factory Default Mode first to program your lock in Standalone Mode.

Add Admin Code in Standalone Mode

Admin Code must be created first prior to any other programming. Only one Admin Code is available.

Operation	Indicator
Hold for 3 sec	2 beeps with flashing green light
Enter 4-8 digit Admin Code and press	1 beep with green light, then flashing green light
Enter the Admin Code again and press	2 beeps with green light
Success	All lights off

Add User Code in Standalone Mode

Operation	Indicator
Hold for 3 sec	2 beeps with flashing blue light
Enter 4-8 digit Admin Code and press	2 beeps with green light, then steady blue light
Enter 4-8 digit User Code and press	1 beep with green light, then steady blue light
Enter the User Code again and press	2 beeps with green light
Success	All lights off

Add Fingerprint in Standalone Mode

Operation	Indicator
Hold for 3 sec	2 beeps with flashing blue light
Enter 4-8 digit Admin Code and press	2 beeps with green light, then steady blue light
Place Your Finger	light
Lift and Place Your Finger	#1 and #2 light with beep
Lift and Place Your Finger	#3 and #4 light with beep
Lift and Place Your Finger	#5 and #6 light with beep
Lift and Place Your Finger	#7 and #8 light with beep
Lift and Place Your Finger	#9 and #0 light with beep
Success	2 beeps with green light

Delete Admin and User

Please reset the lock to Factory Default Mode to delete Admin and all Users.
How to reset the lock in Standalone Mode?
Please use a Reset Needle to push the Reset Button (at the bottom of Interior Assembly) for around 3 seconds until you hear one long beep and two short beeps.

FAQ

How to reset U-Bolt Pro?

Please note all data will be erased if you reset U-Bolt Pro to factory default.
If you are using U-tec App as Owner, please click "Delete and Reset" to remove the lock from your U-tec Account, then use a Reset Needle to push the Reset Button (at the bottom of Interior Assembly) for around 3 seconds until you hear one long beep and two short beeps.
If U-Bolt Pro is working as Standalone Mode, please use a Reset Needle to push the Reset Button (at the bottom of Interior Assembly) for around 3 seconds until you hear one long beep and two short beeps.

How to control U-Bolt Pro remotely?

U-Bolt Pro is a Bluetooth enabled smart lock. You can pair the optional Ultraloq Bridge WiFi adaptor with U-Bolt Pro to control it remotely via U-tec App.

What if I lost the paired smartphone?

Please go to www.u-tec.com/myutec.html or login U-tec App via another smartphone to change your U-tec Account password.

How to adjust the lock orientation of U-Bolt Pro?

The lock orientation must be adjusted after installation to ensure U-Bolt Pro works properly.
Solution 1. Adjust the lock orientation on the lock.
Solution 2. Adjust the lock orientation via U-tec App.

How can I unlock U-Bolt Pro if battery runs out?

There will be low battery alert on the lock and App when battery is low. Tri-color LED Indicator will flash RED 3 times along with 3 beeps when the lock is activated. Please replace batteries.
Solution 1. Use the backup key to unlock.
Solution 2. Connect a 5V power bank to activate the lock temporarily.

What's the difference between Owner, Admin, Normal User and Temporary User?

Owner is the person who owns U-Bolt Pro and registers it in U-tec App originally. Owner has all privileges.
Admin can always unlock via fingerprint, code or App. Admin can add or delete Admin and Users, control all lock settings and view logs.
Normal User can always unlock via fingerprint, code or App. Temporary User has limited access within specific time range.

Does U-Bolt Pro work with accessories such as bolt from third party?

It is recommended to use the original accessories for best performance and stability.

What is the log capacity for U-Bolt Pro?

U-Bolt Pro supports maximum 1000 logs. The latest log will replace the oldest one once log is full.

© 2019 U-tec Group Inc.
U-tec and Ultraloq brands and products are trademarked and protected under law in the United States.
Unauthorized use is prohibited. Ultraloq is sub-brand of U-tec Group Inc.

Videos

Ultraloq U-Bolt Pro | Installation Guide Video

Documents / Resources

References

• U-tec | Ultraloq: The Ultimate Smart Lock
• Privacy policy | U-tec
• U-tec | Ultraloq: The Ultimate Smart Lock

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download U-tec Ultraloq U-Bolt Pro Manual