Transistors Q101 in PCB drive the laser diodes. When Q101 is shorted between their terminals, the laser diodes will radiate beam. If the top cover is removed with no disc loaded while such short-circuit is continued, the naked eyes may be exposed to the laser beam. DEH-1400UB/XNEW5...
Please replace IC671 when making the version upgrade of software. 8. Capacitor Bond Lock Acetate Tape (GYH1026) 1 Please stick acetate tape along white line. 2 Please confirm line hiding with acetate tape. * length of tape : 24 ± 4 mm DEH-1400UB/XNEW5...
Compared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting temperatures (hard to melt/easy to harden). The following lead-free solders are available as service parts: Parts numbers of lead-free solder: GYP1006 1.0 in dia. GYP1007 0.6 in dia. GYP1008 0.3 in dia. DEH-1400UB/XNEW5...
Note Gain ......+6 dB to –24 dB Phase ......Normal/Reverse Specifications and the design are subject to modifications without notice. Securing the front panel The front panel can be secured with the supplied screw. Screw (XXX7020) 2.2 DISC/CONTENT FORMAT DEH-1400UB/XNEW5...
See the table below for the items to be checked regarding audio: Item to be checked regarding audio Distortion Noise Volume too low Volume too high Volume fluctuating Sound interrupted DEH-1400UB/XNEW5...
3.2 PCB LOCATIONS CD Core Unit (S11.6STD) Tuner Amp Unit Keyboard Unit A:DEH-1400UB/XNEW5 B:DEH-1400UBB/XNEW5 C:DEH-1410UB/XNEW5 D:DEH-1420UB/XNEW5 Unit Number : QWM3317(A,B,D) : QWM3318(C) Unit Name : Tuner Amp Unit Unit Number : (A) : (B) : (C) : (D) Unit Name...
CD Mechanism Module 3.4 CLEANING Before shipping out the product, be sure to clean the following portions by using the prescribed cleaning tools: Portions to be cleaned Cleaning tools CD pickup lenses Cleaning liquid : GEM1004 Cleaning paper : GED-008 DEH-1400UB/XNEW5...
In case of the above signal, the communication Source keys with Grille microcomputer may fail. operative If the time interval is not 300 msec, the oscillator may be defective. Source ON SYSPW <- H Pin 7 Completes power-on operation. (After that, proceed to each source operation) DEH-1400UB/XNEW5...
: Servo-related errors CD Off, Eject, ACC Off, Back-up Off, Communication reset, Reset Load NG/Eject NG(50) : Reload, Eject, ACC Off, Back-up Off, Communication reset, Reset Failure in retried turning for ejection : CD On, Eject, ACC Off, Back-up Off, Communication reset, Reset DEH-1400UB/XNEW5...
Page 14
–Change to a dif- ferent source. Then, return to the USB source. ERROR-23 USB storage de- USB storage de- vice was not for- vice should be for- matted with matted with FAT12, FAT16 or FAT12, FAT16 or FAT32. FAT32. DEH-1400UB/XNEW5...
The screen gets still when entering this item. On (an initial value or On (state when setting value of default entering test mode) Switching to next display menu) by pressing “ 1 ” + “ 3 ” keys simultaneously. DEH-1400UB/XNEW5...
When the power is turned on/off the gain of the RFAMP is reset to 0 dB. At the same time all the self-adjusting values shall return to the default setting. Do not do Tracking Servo Close before doing Focus Servo Close. (Because the overcurrent flows) DEH-1400UB/XNEW5...
Lift off the Tuner Amp Assy from the Heat sink side. The Tuner Amp Assy is fixed into the ditch. Disconnect the FFC and then remove the CD Mechanism Module. CD Mechanism Module Fig.4 DEH-1400UB/XNEW5...
Page 19
Remove the two screws. Straighten the tabs at two locations indicated and then remove the Tuner Amp Unit. Fig.5 Tuner Amp Unit Attention of removing (Fig.6) Don't remove this screws excluding the dismantlement of the CD Mechanism Module. Fig.6 DEH-1400UB/XNEW5...
Page 20
1. Attach the button from the front side of the panel. Fig.9 2. Attach the spring to the arm as shown in the figure. The bended tip of the spring is set to this side. Hitch the spring to the groove. Fig.10 DEH-1400UB/XNEW5...
Page 21
4. Fit the boss on the lower side of the arm in the lower hole of the panel, and then warp the rib on the panel in the direction shown in the figure and fit the boss of the arm in the panel. Fig.11 DEH-1400UB/XNEW5...
Page 22
2. Be careful not to hold the solid line portions or the CRG mecha part or insert foreign substances, to prevent distortion. 3. When holding the sides of the upper chassis, do not apply excessive force to prevent distortion. (Approx. 8N or less) Handling OK Handling NG DEH-1400UB/XNEW5...
Page 23
Fig 3 Fig 4 [Incorrect built-in state] The chassis is not nipped between Outer holder Normal built-in state the PU case and the PU rack. Rear end of feeding screw DEH-1400UB/XNEW5...
1k ohms in series. The load and eject operation is not guarantied with the mechanism upside down. If the mechanism is blocked due to mistaken eject operation, reset the product or turn off and on the ACC to restore it. DEH-1400UB/XNEW5...
Because of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may be seen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the average angle. Hint Reloading the disc changes the clamp position and may decrease the "wobble". DEH-1400UB/XNEW5...
With the TESTIN (22 pin) status of IC601 to be “H”, it is shifted to PCL Output Test mode after reset started. Check that square wave of 600.0 kHz is output from PCL (8 Pin) of IC601. If clock signal is out of this range, this resonator (X602) must be changed for a new one. DEH-1400UB/XNEW5...
Screw adjacent to mark on the product are used for disassembly. For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions,apply as you think it appropriate.) 9.1 PACKING Tape DEH-1400UB/XNEW5...
Page 29
See Contrast table (2) Warranty Card CRY1316 Contain Box See Contrast table (2) Case Assy QXA3129 Protector QHP3016 (2) CONTRAST TABLE DEH-1400UB/XNEW5, DEH-1400UBB/XNEW5, DEH-1410UB/XNEW5 and DEH-1420UB/XNEW5 are constructed the same except for the following: DEH-1400UB/ DEH-1400UBB/ DEH-1410UB/ DEH-1420UB/ Mark Description XNEW5 XNEW5...
Page 31
See Contrast table (2) Panel QNS3126 Door QAT3004 Sheet See Contrast table (2) QNV3025 Button QNV3026 (2) CONTRAST TABLE DEH-1400UB/XNEW5, DEH-1400UBB/XNEW5, DEH-1410UB/XNEW5 and DEH-1420UB/XNEW5 are constructed the same except for the following: DEH-1400UB/ DEH-1400UBB/ DEH-1410UB/ DEH-1420UB/ Mark Description XNEW5 XNEW5 XNEW5...
DGND R1804 R1803 DGND V1801 A, C, D CAW2018 CAW2020 SEGMENT LCD SYMBOL SIZE RS1/10SR***J RS1/4SA***J ILMGND D1851-D1865 : SML-D12P8W(KL) only D COLOR2 GREEN REFERENCE AREA MAP GRILLE uCON&LCD 1801-1820 KEY MATRIX & CONNECTOR 1821-1850 1851-1910 1911-1920 only 1921-1930 DEH-1400UB/XNEW5...
Page 41
AUXL DSENS S1841 DISP/BACK DGND CN1911 CKS6267 DGND ILM+B Dimmer off 12.96V C1911 Dimmer on 8.52V 0.1u/16 DGND USBGND DEH-1400UB/EW5 DEH-1400UBB/EW5 DEH-1410UB/EW5 DEH-1420UB/EW5 COLOR1 only D RED/AMBER only A, B, C A, B ILMCLR D1871-D1885 SML-D12V8W(PQ) SML-D12D8W(RS) COLOR AMBER R1871...
1 V/div fRFAGC 500 mV/div 500 mV/div 500 mV/div 9TIN 500 mV/div Focus Search waveform Track Open waveform 100 Track Jump waveform (32 Track Jump x 3) Ref.: Ref.: Ref.: REFO REFO REFO Mode: Mode: Mode: TEST TEST TEST DEH-1400UB/XNEW5...
Page 45
12 cm CD Eject operation 12 cm CD Eject operation Ref.: Ref.: Mode: Mode: Normal Normal 500 μs/div fRFAGC 1 V/div 9TIN 1 V/div 1 V/div aFIN 1 V/div μ Black Dot (800 m) during play Ref.: REFO Mode: Normal DEH-1400UB/XNEW5...
IC 301 (A, 91, 111) IC NJM2068V Circuit Symbol and No. Part No. Circuit Symbol and No. Part No. IC 912 (A,145,28) IC BA49182-V12 A:DEH-1400UB/XNEW5 Q 251 (A,23,130) Chip Transistor RN1910 B:DEH-1400UBB/XNEW5 Q 351 (A,88,127) Chip Transistor RN4983 Q 751 (A,142,138) Transistor...
Page 55
R 501 (A,22,119) RS1/10SR471J R 805 (A,117,18) RS1/10SR8R2J R 502 (A,24,117) RS1/16SS4702F R 806 (A,118,18) RS1/10SR8R2J R 503 (A,22,117) RS1/16SS682J R 807 (A,125,18) RS1/10SR222J R 504 (A,20,119) RS1/16SS1002F R 808 (A,100,18) RS1/10SR222J R 809 (A,104,18) RS1/16SS822J R 505 (A,27,113) RS1/16SS183J DEH-1400UB/XNEW5...
Page 56
C 305 (A,74,131) CKSRYB474K10 C 608 (A,106,67) CKSSYB104K10 C 306 (A,81,131) CKSRYB474K10 C 609 (A,132,67) CKSSYB104K10 C 307 (A,76,131) CKSRYB474K10 C 610 (A,105,66) CKSSYB104K10 C 308 (A,79,131) CKSRYB474K10 C 612 (A,136,66) CKSSYB104K10 C 309 (A,135,134) CKSRYB104K16 C 616 (A,105,62) CKSSYB104K10 DEH-1400UB/XNEW5...
Page 57
: Keyboard Unit R 1805 (B,145,33) RS1/10SR473J R 1822 (B,54,24) RS1/10SR273J MISCELLANEOUS R 1823 (B,131,19) RS1/10SR0R0J IC 1801 (B,85,23) IC PD6581A R 1824 (B,69,26) RS1/10SR0R0J D 1851 (A,16,30) LED(D) SML-D12P8W(KL) R 1851 (B,18,27) (D) RS1/4SA681J D 1852 (A,53,30) LED(D) SML-D12P8W(KL) DEH-1400UB/XNEW5...
Page 58
C 224 (B,13,45) CCSSCH470J50 R 202 (A,23,9) RS1/16SS0R0J C 225 (B,13,46) CKSSYB103K16 R 214 (B,18,28) RS1/16SS103J C 228 (B,10,33) CCSSCH270J50 R 215 (B,17,28) RS1/16SS393J R 216 (B,12,35) RS1/16SS122J C 229 (B,9,40) CKSSYB104K10 C 233 (B,32,46) CKSSYB103K16 R 217 (B,10,32) RS1/16SS562J DEH-1400UB/XNEW5...
Page 59
C 303 (B,29,12) CKSSYB102K50 C 304 (B,27,12) CKSSYB223K16 C 305 (B,26,12) CKSSYB104K10 C 306 (A,31,7) CKSSYB104K10 C 307 (A,41,19) CKSRYB105K10 C 308 (A,31,15) CKSRYB105K10 C 710 (A,34,42) CKSSYB102K50 Miscellaneous Parts List Pickup Unit(P10.6)(Service) CXX3556 Motor Unit(SPINDLE) CXE2273 Motor Unit(LOADING/CARRIAGE) CXC4026 DEH-1400UB/XNEW5...
Need help?
Do you have a question about the DEH-1400UB and is the answer not in the manual?
Questions and answers