Summary of Contents for LMC Systems TC
- Page 1 Operator’s Manual Rotary Tiller TC & RT LMC AG 1715 South Slappey Blvd. Albany, Ga. 31701 229-639-1775...
-
Page 2: Table Of Contents
WORKING DEPTH ADJUSMENT………………………………………….………………………………10 TALILGATE ADJUSTMENT…. ……..………………………………………………….…………………..10 START UP……………………………………………………………………………………………………………10 REMOVAL AND STORAGE…………………………………………………………………………………..10 TC ROTARY TILLER: PARTS BREAKDOWN …………………………………………………... 12-15 RT ROTARY TILLER: PARTS BREAKDOWN …………………………………………………... 17-19 PTO SHAFT: PARTS BREAKDOWN ……………………………………………………………………..20 WARRANTY REGISTRATION FORM & INSPECTION REPORT ........21 LIMITED WARRANTY ..................... 23... -
Page 3: Introduction
INTRODUCTION Thank you for purchasing your LMC Ag Rotary Tiller. Your Rotary Tiller is designed to be used on Cat. 1 tractors and at 540 RPM. It is important to properly maintain and keep in place all safety guards and shields that came with your rotary tiller. -
Page 4: Safety Signal Words
SAFETY SIGNAL WORDS Note the use of the signal words DANGER, WARNING and CAUTION with the safety mes- sages. The appropriate signal word for each has been selected using the following guidelines: DANGER: Indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury. -
Page 5: Safety Decal Care
SAFETY DECAL CARE • Keep safety signs clean and legible at all times. • Replace safety signs that are missing or have become illegible. • Replaced parts that displayed a safety sign should also display the current sign. • Safety signs are available from your Distributor or Dealer Parts Department or the factory. How to Install Safety Signs: •... -
Page 6: During Operation
• Don’t hurry the learning process or take the unit for granted. Ease into it and become familiar with your new equipment. • Practice operation of your equipment and its attachments. Completely familiarize yourself and other operators with its operation before using. •... -
Page 7: Highway And Transport Operations
• DO NOT operate near the edge of drop-offs or banks. • DO NOT operate on steep slopes as overturn may result. • Operate up and down (not across) intermediate slopes. Avoid sudden starts and stops. HIGHWAY AND TRANSPORT OPERATIONS •... - Page 8 • Watch for obstructions overhead and to the side while transporting. • Always operate equipment in a position to provide maximum visibility at all times. Make allow- ances for increased length and weight of the equipment when making turns, stopping the unit, etc.
-
Page 9: Important Instructions Before First Use
PLEASE READ BEFORE FIRST USE OF ROTARY TILLER Check the EP0 / EP2 grease in the gearboxes and grease fittings prior to use. Running the machine without lubricates voids the warranty • The gearbox for your Rotary Tiller requires EP0 / EP2 grease in the center gearbox. The side gearbox uses 140 wt or 00 liquid grease. - Page 10 Picture A Picture B Picture C Picture D Picture E Picture F...
-
Page 11: Attaching To Tractor
Attachment to the Tractor Before attaching the equipment to the tractor, make sure that the ground is smooth and flat and that nobody is standing between the tractor and the tiller; slowly move the tractor towards the tiller by aligning the tractor lifter arms with the two tiller coupling side pins; turn the engine off and pull the brake. -
Page 12: Working Depth Adjusment
Working Depth Adjustment It is necessary to perform all maintenance work on the Rotary Tiller before every use as well as clearly understanding the safety information. Remember to NEVER make any adjustments to the Rotary Tiller while the tractor is running. Allowing the tractor engine OR rotary tiller to stall or bog down will cause unnecessary wear on both the tiller and the tractor. - Page 13 Maintenance It is critical to properly maintain your Rotary Tiller and is entirely your responsibility. Periodically checking and maintaining the optimum EP0 / EP2 grease level is a must. Every 8 Working Hours, please grease: • Out-Board hub • PTO Shaft universal joints •...
-
Page 14: Tc Rotary Tiller: Parts Breakdown
TC Rotary Tiller... - Page 15 TX0304-40 Drive Shaft TC-040 TX0304-50 Drive Shaft TC-050 TX0304-60 Drive Shaft TC-060 TX0306 Gasket TX0301-40 Drive Shaft Tube Housing TC-040 TX0301-50 Drive Shaft Tube Housing TC-050 TX0301-60 Drive Shaft Tube Housing TC-060 BM101525 Bolt -10 x 25 TX03012 Ring Gear...
- Page 16 TC Rotary Tiller...
- Page 17 TC Rotary Tiller Position Part # Description OP121250 Oil Plug TX0310 Lifting Hook BM1217530 Bolt -12x 30 DP1615000V Breather cap BM101525 Bolt -10 x 25 YT1066050200 Stand Bracket RC300000 R-Clip - 3mm YT10660501 Pin - Stand YT1066050100 Stand Leg TX0601...
- Page 18 RT Rotary Tiller...
-
Page 19: Rt Rotary Tiller: Parts Breakdown
RT Rotary Tiller Position Part # Description Hitch Pin (Lower Hitch Block) CT20114 Bolt - 16 x 1.5 x 45 BM161545 A Frame - Right CT20103 A Frame - Left CT20102 BM101525 Bolt - Drive tube housing Gearbox Shielding (complete) CT20105 Lift Arm Brace CT20101... - Page 20 RT Rotary Tiller...
- Page 21 RT Rotary Tiller Position Part # Description Drive Shaft Tube Housing - RT4 CT103224 Drive Shaft Tube Housing - RT5 CT103225 Drive Shaft Tube Housing - RT6 CT103226 Drive Shaft Tube Housing - RT7 CT103227 OS65408 Oil Seal - Drive shaft tube housing Ring Gear YT10660206 Oil Plug Center GB (Drain Plug)
-
Page 22: Pto Shaft: Parts Breakdown
PTO Shaft Pos. Part # Description DP1075-40 PTO Yoke - Series 40 DP1075-60 PTO Yoke - Series 60 DP1079-40 Female Yoke and Tube (tractor end) - Series 40 DP1079-60 Female Yoke and Tube (tractor end) - Series 60 DP1076-40 Cross and Bearings - Series 40 DP1076-60 Cross and Bearings - Series 60 DP1078-40... -
Page 23: Warranty Registration Form & Inspection Report
WARRANTY REGISTRATION FORM & INSPECTION REPORT WARRANTY REGISTRATION This form must be filled out by the dealer and signed by both dealer and customer at time of delivery. Customer name _____________________ Dealer name _____________________ Address __________________________ Address ________________________ City, state, code _____________________ City, state, code ___________________ _____________________ ___________________ Phone number (__)-__-_____... -
Page 24: Limited Warranty
LIMITED WARRANTY LMC Ag warrants to the original purchaser of any new LMC Ag equipment purchased from an authorized LMC Ag dealer, that the equipment be free from defects in material and workmanship for a period of one (1) year for noncommercial, state, and municipalities’... - Page 26 LMC AG 1715 South Slappey Blvd. Albany, Ga. 31701 1-800-673-6369 Fax 1-229-446-8333 www.lmcag.com...
Need help?
Do you have a question about the TC and is the answer not in the manual?
Questions and answers