Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Jet JTAS-10XL
Summary of Contents for Jet JTAS-10XL
- Page 1 This manual is bookmarked Operating Instructions and Parts Manual Left Tilting Arbor Saw Models JTAS-10XL and JTAS-12XL JTAS-10XL shown WMH TOOL GROUP 2420 Vantage Drive Elgin, Illinois 60123 Part No. M-708661 Ph.: 800-274-6848 Revision H 7/06 www.wmhtoolgroup.com Copyright © WMH Tool Group...
-
Page 2: Warranty
Centers located throughout the United States can give you quick service. In most cases, any of these WMH Tool Group Authorized Service Centers can authorize warranty repair, assist you in obtaining parts, or perform routine maintenance and major repair on your JET® tools. For the name of an Authorized Service Center in your area call 1-800-274-6848. MORE INFORMATION WMH Tool Group is consistently adding new products to the line. -
Page 3: Warnings
2. This table saw is designed and intended for use by properly trained and experienced personnel only. If you are not familiar with the proper and safe operation of a table saw, do not use until proper training and knowledge have been obtained. -
Page 4: Table Of Contents
Now that you have purchased a tablesaw, it is a good time to consider a dust collection system. See your local JET distributor for the complete line of dust collectors and the full line of JET Dust Collector Hoses and Accessories. Customize your installation and obtain maximum performance with JET's dust hoods, hoses, clamps, fittings, and blast gates. -
Page 5: Specifications
*Conversion to 460V requires the purchase and installation of switch #JTAS10-23B. The JTAS-10XL and JTAS-12XL Tilting Arbor Tablesaws are designed to allow the use of several precision fences by various manufacturers. Please follow the directions for mounting the fence and rails that come with the fence system you have purchased. -
Page 6: Contents Of The Shipping Container
WARNING Read and understand the entire contents of this manual before attempting assembly or operation! Failure to comply may cause serious injury! Contents of the Shipping Container 1. Saw 1. Motor Cover 2. Extension Wings Accessory Package: 1. Blade Guard Assembly 1. -
Page 7: Installation And Leveling
WARNING Do not connect the tablesaw to the power source until all assembly has been completed! Failure to comply may cause serious injury! Installation and Leveling Final location for the saw must be level, dry, well lighted, and have enough room to allow movement around the saw with long pieces of wood stock. -
Page 8: Handwheel Assembly
Handwheel Assembly • Hardware: Handle & Hand Wheel, Lock Knob • Tool: 3mm Hex Wrench 1. Line up the key on the shaft with the key way in the handwheel (A, Fig. 4) and slide the handwheel onto the shaft. 2. -
Page 9: Installing Blade
Installing Blade WARNING When installing or changing saw blade, always disconnect saw from the power source! Failure to comply may cause serious injury! • Hardware: Blade • Tool: Arbor Wrench, Scrap Piece of Wood 1. Raise the blade arbor fully and lock the saw at zero by tightening the lock knob in the middle of the handwheel. -
Page 10: Table Insert Adjustment
Table Insert Adjustment • Hardware: Table Insert • Tools: Straight Edge, 2.5mm Hex Wrench 1. Lower blade completely. 2. Place the open end of the insert under the splitter and lower the insert into the opening. 3. Adjust the table insert flush with the table by turning four leveling screws (A, Fig. -
Page 11: Blade Raising And Tilting Mechanism
Failure to comply may result in serious injury! The JTAS-10XL-1, JTAS-10XL-5/1 and JTAS- 12XL-5/1 table saws are rated at 230V only. The JTAS-10XL-3 and JTAS-12XL-3 are rated at 230/460V, and come from the factory prewired 230V. To switch the JTAS-10XL-3 and JTAS-12XL-3 from 230V to 460V: 1. -
Page 12: Blade Alignment
Blade Alignment • Tool: 8mm Hex Wrench, combination square, marker Blade alignment with the table is adjusted at the factory. After a period of use, or, after moving the saw to another location, the blade may no longer be aligned with the table. To check and align the blade: see Figure 13 1. -
Page 13: Adjusting 45° And 90° Positive Stops
Adjusting 45° ° ° ° and 90° ° ° ° Positive Stops The stops have been adjusted at the factory. After a period of use, or, after moving the saw to another location, the stops may no longer be set properly. -
Page 14: Changing Belts
Changing Belts WARNING Make all machine adjustments or maintenace with the machine unplugged from the power source. Failure to comply may cause serious injury! 1. Disconnect the machine from the power source, unplug. 2. Lower the blade to its lowest point. 3. -
Page 15: Troubleshooting
Trouble Saw stops or will not start Does not make accurate 45° ° ° ° or 90° ° ° ° cuts Material binds blade when ripping Saw makes unsatisfactory cuts Blade does not come up to speed Saw vibrates excessively Rip fence binds on guide rails Material kicked back from blade... -
Page 16: Parts Breakdown And Parts List
Table and Cabinet Assembly – JTAS-10XL... - Page 17 ...JTAS12-33... Power Cord Sleeve * ..1 34 ...JTAS10L-34 ... Tilt Scale ..1 35 ...JTAS10-35... Warning Label ..1 36 ...JTAS10L-36 ... JET Label ..1 38 ...JTAS10L-38WA ... Cabinet…..1 39 ...TS-1482101 ... Hex Cap Bolt ...M6x50... 1 40 ...TS-0680021 ...
- Page 18 Index Part Description Size Qty. 49 ...JTAS10-50W ... Lower Panel..1 50 ...JTAS10-51... Dust Hose Adapter..1 51 ...JTAS10-52W ... Switch Brace Kit ** ..1 52 ...JTAS10-53... Screw ...3/16 x 1... 1 53 ...JTAS10-54... Nut ...3/16... 1 54 ...JTAS10-55...
- Page 19 Blade Guard Assembly – JTAS-10XL...
- Page 20 Blade Guard Assembly – JTAS-10XL Index Part Description ...JTAS10L-BG... Blade Guard Assembly (# 1-10/13/23-26) ... 1 1...JTAS10-G1 ... Pin..1 2...JTAS10L-G2 ... Guard ..1 3...TS-0207091 ... Hex Socket Cap Screw...1/4x1-1/2... 1 4...TS-0680021 ... Flat Washer...1/4 ... 1 5...JTAS10-G5 ...
- Page 21 Motor and Trunnion Assembly – JTAS-10XL...
- Page 22 Motor and Trunnion Assembly – JTAS-10XL Index Part 101 ...JTAS10L-101 ... Arbor Nut ..1 102 ...JTAS10-102 ... Arbor Flange..1 104 ...JTAS10L-104 ... Arbor with Flange ..1 105 ...JTAS10-105 ... Key ...M5x1-1/2... 2 106 ...BB-6203ZZ ... Ball Bearing..2 107 ...JTAS10-107 ...
- Page 23 Index Part Description Size Qty. 148 ...JTAS10-148 ... Key...M5x35... 2 149 ...TS-0051071 ... Hex Cap Bolt ...5/16x1-1/2... 2 150 ...JTAS10L-150 ... Dust Deflector..1 151 ...JTAS10-151 ... Spacer..2 152 ...JTAS10L-152 ... Front Trunnion..1 ...JTAS10L-TA ... Trunnion Assy. (#113, 135-141) ..1 153 ...TS-0051021 ...
- Page 24 Table and Cabinet Assembly – JTAS-12XL...
- Page 25 ...JTAS12-33... Power Cord Sleeve * ..1 34 ...JTAS10L-34 ... Tilt Scale ..1 35 ...JTAS10-35... Warning Label ..1 36 ...JTAS10-36... JET Label ..1 38 ...JTAS12L-38W ... Cabinet..1 39 ...TS-1482101 ... Hex Cap Screw...M6x50... 1 40 ...TS-0680021 ...
- Page 26 52 ...TS-081C062... Screw ...#10-24x1... 1 53 ...TS-0560071 ... Nut ...#10-24... 3 54 ...TS-0733031 ... Star Washer ...#10... 1 * Saws with 5HP, 1Ph motor use these parts. ** Switch Brace kit contains bracket, screw, nut, star washer, and 8mm hex wrench.
- Page 27 Blade Guard Assembly – JTAS-12XL...
- Page 28 Blade Guard Assembly – JTAS-12XL Index Part Description ...JTAS12L-BG... Blade Guard Assembly (# 1-10, 13, 23-26) ... 1 1...JTAS10-G1 ... Pin..1 2...JTAS12L-G2 ... Guard ..1 3...TS-0207081 ... Socket Head Cap Screw...1/4-20x1-1/2... 1 4...TS-0680021 ... Flat Washer...1/4 ... 1 5...JTAS10-G5 ...
- Page 29 Motor and Trunnion Assembly – JTAS-12XL...
- Page 30 Motor and Trunnion Assembly – JTAS-12XL Index Part Description 101 ...JTAS12L-101 ... Arbor Nut ..1 102 ...JTAS12-102 ... Arbor Flange..1 104 ...JTAS12L-104 ... Arbor with Flange ..1 105 ...JTAS12-105 ... Key ...M5x1-1/2... 2 106 ...BB-6005ZZ ... Ball Bearing...6005ZZ ... 2 107 ...JTAS10-107 ...
- Page 31 154 ...TS-0561021 ... Hex Nut ...5/16-18... 2 155 ...JTAS12L-155 ... Lock Knob ..2 156 ...JTAS10-156 ... Fiber Washer..2 157 ...TS-0208101 ... Socket Head Cap Screw...5/16-18x2... 2 158 ...JTAS12L-158 ... Front Trunnion Bracket ..1 159 ...JTAS10L-159 ... Hand Wheel Handle ..2 160 ...JTAS10L-160 ...
-
Page 32: Electrical Schematic
Electrical Schematic - Single Phase... -
Page 33: Electrical Schematic
Electrical Schematic - Three Phase... - Page 34 NOTES...
- Page 36 WMH Tool Group 2420 Vantage Drive Elgin, Illinois 60124 Phone: 800-274-6848 www.wmhtoolgroup.com...
Need help?
Do you have a question about the JTAS-10XL and is the answer not in the manual?
Questions and answers