Essentim Scope 4 User Manual

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

User Guide

Table of Contents

Summary of Contents for Essentim Scope 4

Page 1 User Guide...
Page 2 © essentim GmbH | Schragenhofstrasse 35 | D-80992 München www.essentim.com info@essentim.com user manual scope - version 1.1...
Page 3: Table Of Contents
Table of Content Notes Safety Instructions Intended Use and User Device Description General Information scope Technical data Transport and Storage Commissioning Device functions Button Switch on / switch oﬀ Reset User interaction with the scope LED function Find / Identify scope (App) Memory (App) Operating modes (App) Magic Time (App)
Page 4 Disposal Changelog user manual scope - version 1.1...
Page 5: Notes
Directive 2002/96 / EC (WEEE). Legal information No part of this document may be reproduced, electronically reproduced or distributed in any form without a written permission of essentim GmbH. essentim GmbH assumes no liability for any errors or omissions. The determination of valid measurement results, conclusions and measures derived therefrom are solely the sole responsibility of the user.
Page 6: Safety Instructions
Safety Instructions Read these safety instructions carefully before using the device and always keep the instructions accessible! Warning! Always observe all safety instructions in this document! A non-observance may result in personal injury or property damage! Always keep the safety instructions and the user manual accessible. Observe all technical limits and storage conditions for the device.
Page 7: Intended Use And User
Scopes must be charged at room temperature (but in any case between 0 °C and 40 °C). ● Only use essentim approved cables and extension in conjunction with the scope. ● Avoid mechanical stress on the scope, damage to the housing may damage the ●...
Page 8: Device Description
Through an electrostatic adhesive strip ("Gecko-strip"), the scope can be attached to smooth surfaces and removed without leaving any residue easily. To achieve a 24/7 monitoring the scope can be used in combination with the wireless sensor infrastructure of essentim. This requires at least one essentim gateway. Further information can be found at www.essentim.com/en/essentim-sensors.
Page 9: Technical Data
Technical data Producer essentim GmbH Model scope version 4 Type Wireless multi-parameter-sensor Power supply for charging 5V DC (min. 50mA) Battery type Lithium-Polymer-Battery, 35mAh, rechargeable, firmly installed Operating conditions (EN / IEC 61010-1) Operating location Inside, in a transport box with securing, not for outdoor...
Page 10: Transport And Storage
Always take into account the transport guidelines of your transport service provider when transporting lithium-containing batteries. Information can be obtained directly from the transport service provider or contact essentim. Unused scopes should be stored with a charge of about 30 %.
Page 11: Commissioning
Remove the protective foil from the Gecko-strip on the back of the scope. Note To use the battery eﬀectively, the scope should always be fully discharged and then fully charged. Warning! Only use essentim accessories to charge the scope. user manual scope - version 1.1...
Page 12: Device Functions
In the switched-on mode, pressing the button briefly will result in an event which is sent via Bluetooth. In the essentim apps, an interaction with the scope can thus be determined. At the same time, corresponding windows open and commands can be executed. When manually reading out stored data, the button on the scope must be briefly pressed once to start the transmission.
Page 13: Led Function
LED function The red and green LEDs provide feedback on the current situation of the scope. In principle, the red LED indicates a problem (exception when switching oﬀ), while the green LED indicates an activity. Action Flash code LED colour switch on „long short short short”...
Page 14: Operating Modes (App)
The readout is done automatically in a sensor network of essentim or can be triggered manually by the user through the app. Operating modes (App) Diﬀerent situations require diﬀerent behavior of the scope. We have defined three possible modes to perform a variety of measurement tasks.
Page 15: Static Mode
Static Mode In Static Mode, measured data is always transmitted and stored at the same interval. The time value can be set in static mode via the Magic Time. The figure shows the data points of a scope in Static Mode with a Magic Time of 15 seconds. The distance between the measuring points is always constant.
Page 16: Cleaning, Maintenance And Repair
The scope can be cleaned with distilled water or Isopropanol (70%). The cleaning fluid should be applied with a wet wipe or by direct wetting. essentim recommends the following procedure for cleaning: Turn oﬀ the scope. Insert the anti-dust plugs into the charging interface.
Page 17: Faqs
How can I set the time of the scope? The time is automatically set as soon as the scope is connected to a sensor network or connected to an essentim app. The time is a precondition for storing the data in the local memory of the scope.
Page 18: Troubleshooting
Troubleshooting The scope can not be turned on, I see no feedback from the LEDs. Not even if I press the button. Try to charge the scope. If the scope is completely uncharged, it can only be switched on via charging, not via the button. Press the button for 13 seconds.
Page 19 Before disposal, the scope must be completely discharged, so that it can not be switched on again by a button pressure. The devices can be brought to collection points for waste electrical and electronic equipment for disposal. WEEE registration number of essentim GmbH: DE 22316070. user manual scope - version 1.1...
Page 20 Changelog 18.01.2018 Erstellung der Bedienungsanleitung 21.08.2018 Überarbeitung der Bedienungsanleitung 18.09.2018 Übersetzung der Bedienungsanleitung (Englisch) 14.03.2022 Design Aktualisierung 22.04.2022 Entfernung der EG Declaration of Conformity user manual scope - version 1.1...