Page 5
1. Precautions 1. Precautions 1-1. Safety Precautions Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential hazards such as electrical shock. 1-1-1. Warnings For continued safety, do not attempt to modify the circuit board. Disconnect the AC power and DC power jack before servicing.
Page 6
1. Precautions 1-1-4. Product Safety Notices Some electrical and mechanical parts have special safetyrelated characteristics which are often not evident from visual inspection. The protection they give may not be obtained by replacing them with components rated for higher voltage, wattage, etc.
Page 7
1. Precautions 1-2. Servicing Precautions An electrolytic capacitor installed with the wrong polarity might explode. WARNING Before servicing units covered by this service manual, read and follow the Safety Precautions section of this manual. CAUTION If unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions, always follow the safety precautions.
Page 8
1. Precautions 1-3. Static Electricity Precautions Some semiconductor (solid state) devices can be easily damaged by static electricity. Such components are commonly called Electrostatically Sensitive Devices (ESD). Examples of typical ESD are integrated circuits and some field-effect transistors. The following techniques will reduce the incidence of component damage caused by static electricity. Immediately before handling any semiconductor components or assemblies, drain the electrostatic charge from your body by touching a known earth ground.
Page 9
1. Precautions 1-4. Installation Precautions For safety reasons, more than a people are required for carrying the product. Keep the power cord away from any heat emitting devices, as a melted covering may cause fire or electric shock. Do not place the product in areas with poor ventilation such as a bookshelf or closet. The increased internal temperature may cause fire.
Page 10
ANNEX. Exploded View & Part List ANNEX. Exploded View & Part List [UE55KS8000FXZA FA01] 1-1. Exploded View 1-1-1. Parts List Code No. Description & Specification Q’ty SA/SNA Remark BN95-02609A PRODUCT LCD-SDC; CY-QK055FLLV2V/H,KS7000, BN96-39617A ASSY COVER P-DECORATION; 55KS7000,PC+GF1 BN44-00878A DC VSS-PD BOARD; L55E7_KSM,AC/DC,192W,100 BN96-39888A ASSY SPEAKER P-FRONT;...
Page 11
ANNEX. Exploded View & Part List 1-2. ONE CONNECT Exploded View 1-2-1. Parts List Code No. Description & Specification Q’ty SA/SNA Remark BN96-40188B ASSY COVER P-TOP; 55KS9000,ABS,V-0,BK0008 BN94-10924A ASSY PCB MISC-ONE CONNECT MINI; Y16 OCM P BN63-15074B COVER-BOTTOM; OCM PLUS,PC+ABS,MOLD,V-0, ANNEX-2...
Page 12
ANNEX. Exploded View & Part List 2-1. Electrical Parts List Service Bom (SA: SERVICE AVAILABLE, SNA: SERVICE NOT AVAILABLE) Level Location No. Code No. Description & Specification Q’ty SA/SNA Remark UN55KS8000FXZA (FA01) BN90-07963A ASSY W/I;7K BN81-08159Z A/S PART SET-ELEC W/I;LED TV ELEC spec-C BN81-12184F A/S PART SET-MECH W/I;UKS7000S,U55KS* R001A...
Page 20
ANNEX. Exploded View & Part List ANNEX. Exploded View & Part List [UE49KS8000FXZA FA01] 1-1. Exploded View ANNEX-1...
Page 21
ANNEX. Exploded View & Part List 1-1-1. Parts List Code No. Description & Specification Q’ty SA/SNA Remark BN95-02609A PRODUCT LCD-SDC; CY-QK055FLLV2V/H,KS7000, BN96-39617A ASSY COVER P-DECORATION; 55KS7000,PC+GF1 BN44-00878A DC VSS-PD BOARD; L55E7_KSM,AC/DC,192W,100 BN96-39888A ASSY SPEAKER P-FRONT; 6ohm,40W,2.1CH BN59-01239A NETWORK-WLAN CLIENT; WCK730B,USB 2.0,16P, BN96-39685A ASSY COVER P-REAR;...
Page 22
ANNEX. Exploded View & Part List 1-2. ONE CONNECT Exploded View 1-2-1. Parts List Code No. Description & Specification Q’ty SA/SNA Remark BN96-40188B ASSY COVER P-TOP; 55KS9000,ABS,V-0,BK0008 BN94-10924A ASSY PCB MISC-ONE CONNECT MINI; Y16 OCM P BN63-15074B COVER-BOTTOM; OCM PLUS,PC+ABS,MOLD,V- ANNEX-3...
Page 23
ANNEX. Exploded View & Part List 2-1. Electrical Parts List Service Bom (SA: SERVICE AVAILABLE, SNA: SERVICE NOT AVAILABLE) Level Location No. Code No. Description & Specification Q’ty SA/SNA Remark UN49KS8000FXZA (FA01) BN90-07963D ASSY W/I;7K BN81-08159Z A/S PART SET-ELEC W/I;LED TV ELEC spec-C BN81-12184E A/S PART SET-MECH W/I;UKS7000S,U49KS* R001A...
Page 32
ANNEX. Exploded View & Part List ANNEX. Exploded View & Part List [UE60KS8000FXZA EA01] 1-1. Exploded View 1-1-1. Parts List Code No. Description & Specification Q’ty SA/SNA Remark BN95-02642A PRODUCT LCD-SHARP; CY-QK060FLSV1V/H,KS700 BN96-39711A ASSY CHASSIS FRONT P; 60KS7000,AL,SILVER, BN44-00880A DC VSS-PD BOARD; L65E8N_KSM,AC/DC,237W,10 BN96-39684A ASSY COVER P-REAR;...
Page 33
ANNEX. Exploded View & Part List 1-2. ONE CONNECT Exploded View 1-2-1. Parts List Code No. Description & Specification Q’ty SA/SNA Remark BN96-40188B ASSY COVER P-TOP; 55KS9000,ABS,V-0,BK0008 BN94-10924A ASSY PCB MISC-ONE CONNECT MINI; Y16 OCM P BN63-15074B COVER-BOTTOM; OCM PLUS,PC+ABS,MOLD,V-0,BK ANNEX-2...
Page 34
ANNEX. Exploded View & Part List 2-1. Electrical Parts List Service Bom (SA: SERVICE AVAILABLE, SNA: SERVICE NOT AVAILABLE) Level Location No. Code No. Description & Specification Q’ty SA/SNA Remark UN60KS8000FXZA (EA01) BN90-07963G ASSY W/I;7K BN81-08159Z A/S PART SET-ELEC W/I;LED TV ELEC spec-C BN81-12184G A/S PART SET-MECH W/I;UKS7000S,U60KS* R001A...
Page 43
ANNEX. Exploded View & Part List ANNEX. Exploded View & Part List [UE65KS8000FXZA FA01] 1-1. Exploded View 1-1-1. Parts List Code No. Description & Specification Q’ty SA/SNA Remark BN95-02610A PRODUCT LCD-SDC; CY-QK065FLLV2V/H,KS7000, BN96-39626A ASSY COVER P-DECORATION; 65KS7000,PC+GF15 BN44-00880A DC VSS-PD BOARD; L65E8N_KSM,AC/DC,237W,10 BN96-39683A ASSY COVER P-REAR;...
Page 44
ANNEX. Exploded View & Part List 1-2. ONE CONNECT Exploded View 1-2-1. Parts List Code No. Description & Specification Q’ty SA/SNA Remark BN96-40188B ASSY COVER P-TOP; 55KS9000,ABS,V-0,BK0008 BN94-10924A ASSY PCB MISC-ONE CONNECT MINI; Y16 OCM P BN63-15074B COVER-BOTTOM; OCM PLUS,PC+ABS,MOLD,V-0,BK ANNEX-2...
Page 45
ANNEX. Exploded View & Part List 2-1. Electrical Parts List Service Bom (SA: SERVICE AVAILABLE, SNA: SERVICE NOT AVAILABLE) Level Location No. Code No. Description & Specification Q’ty SA/SNA Remark UN65KS8000FXZA (FA01) BN90-07963B ASSY W/I;7K BN81-08159Z A/S PART SET-ELEC W/I;LED TV ELEC spec-C BN81-12184H A/S PART SET-MECH W/I;UKS7000S,U65KS* R001A...
Page 53
ANNEX. Exploded View & Part List Level Location No. Code No. Description & Specification Q’ty SA/SNA Remark BN60-01010C SPACER-CONDUCTIVE;55KS7000,CONDUCTIVE FA BN60-01251H SPACER-CONDUCTIVE;65KS7500,CONDUCTIVE FA BN63-11875N SHEET-PROTECTION COVER;SD590,AL,T0.068,W FD01 BN63-15064A COVER-DECORATION;65KS7000,PC+GF15%,MOLD, BN74-00053E TAPE-PAPER;PAPER,3M2307,0.14T,W20,50m,WH BN96-39715A ASSY BLU P-DECO;KS7000/7500,SK5EB00070,L ANNEX-11...
Page 54
2. Product specifications 2. Product Specifications 2-1. Product information Model UN**KS8000F Front View * W : Width H : High D : Depth Detail View Front Color Silver without Stand 42.9 x 24.9 x 1.7 inches 49" with Stand 42.9 x 27.5 x 9.2 inches without Stand 48.2 x 28.0 x 1.7 inches 55"...
Page 55
2. Product specifications 2-2. Detail Specification Item UN49KS8000FXZA General Information Product SUHD Series Country UNITED STATES Platform(TV) SoC | JAZZ-M Display Screen Size 49" Resolution 3,840 × 2,160 Ultra Black Quantum Dot Display Ultra Clear Panel Ultra Clear Ultimate Screen Curvature 10 bit Support Video Picture Engine...
Page 56
Mobile to TV - Mirroring, DLNA Family Square with S-Cloud Together Play Easy Setup Samsung SMART View App Casting Wireless TV On - Samsung WOL Wired TV On - Samsung WOL Bluetooth Low Energy Briefing On TV WiDi WiFi Direct...
Page 57
Bezel-less Slim Type Premium Slim Front Color Silver Light Effect (Deco) Stand Type Branch Swivel (Left/Right) Additional Feature Samsung 3D Instant On Processor Quad-Core SCSA Support Accessibility Voice Guide/Enlarge/High Contrast Digital Clean View One Connect (Jack) Auto Channel Search Auto Power Off...
Page 58
2. Product specifications Item UN49KS8000FXZA Additional Feature Time Shift V-Chip MBR Support Ultra Clean View Eco Feature Energy Star Eco Sensor Energy Efficiency Class Power Power Supply AC110-120V 50/60Hz Power Consumption (Max) 163 W Power Consumption (Stand-by) 0.3 W Power Consumption (Typical) 55 W...
Page 59
2. Product specifications Item UN55KS8000FXZA General Information Product SUHD Series Country UNITED STATES Platform(TV) SoC | JAZZ-M Display Screen Size 55" Resolution 3,840 × 2,160 Ultra Black Quantum Dot Display Ultra Clear Panel Ultra Clear Ultimate Screen Curvature 10 bit Support Video Picture Engine SUHD Remastering Engine...
Page 60
Mobile to TV - Mirroring, DLNA Family Square with S-Cloud Together Play Easy Setup Samsung SMART View App Casting Wireless TV On - Samsung WOL Wired TV On - Samsung WOL Bluetooth Low Energy Briefing On TV WiDi WiFi Direct...
Page 61
Anynet+ (HDMI-CEC) Design Design Triumph-Flat Bezel Type Bezel-less Slim Type Premium Slim Front Color Silver Light Effect (Deco) Yes (Samsung Badge Lighting) Stand Type Branch Shape (Silver) Swivel (Left/Right) Additional Feature Samsung 3D Instant On Processor Quad-Core SCSA Support Accessibility...
Page 62
2. Product specifications Item UN55KS8000FXZA Additional Feature Smart Evolution Support Teletext (TTX) Time Shift V-Chip MBR Support Ultra Clean View Eco Feature Energy Star Eco Sensor Energy Efficiency Class Power Power Supply AC110-120V 50/60Hz Power Consumption (Max) 165 W Power Consumption (Stand-by) 0.3 W Power Consumption (Typical) 60 W...
Page 63
2. Product specifications Item UN60KS8000FXZA General Information Product SUHD Series Country UNITED STATES Platform(TV) SoC | JAZZ-M Display Screen Size 60" Resolution 3,840 × 2,160 Ultra Black Quantum Dot Display Ultra Clear Panel Ultra Clear Ultimate Screen Curvature 10 bit Support Video Picture Engine SUHD Remastering Engine...
Page 64
Mobile to TV - Mirroring, DLNA Family Square with S-Cloud Together Play Easy Setup Samsung SMART View App Casting Wireless TV On - Samsung WOL Wired TV On - Samsung WOL Bluetooth Low Energy Briefing On TV WiDi WiFi Direct...
Page 65
Wireless LAN Built-in Anynet+ (HDMI-CEC) Design Design Triumph-Flat Bezel Type Slim Type Premium Slim Front Color Silver Light Effect (Deco) Yes (Samsung Badge Lighting) Stand Type Branch Shape (Silver) Swivel (Left/Right) Additional Feature Samsung 3D Instant On Processor Quad-Core SCSA Support Accessibility...
Page 66
2. Product specifications Item UN60KS8000FXZA Additional Feature Smart Evolution Support Teletext (TTX) Time Shift V-Chip MBR Support Ultra Clean View Eco Feature Energy Star Eco Sensor Energy Efficiency Class 2-13...
Page 67
2. Product specifications Item UN65KS8000FXZA General Information Product SUHD Series Country UNITED STATES Platform(TV) SoC | JAZZ-M Display Screen Size 65" Resolution 3,840 × 2,160 Ultra Black Quantum Dot Display Ultra Clear Panel Ultra Clear Ultimate Screen Curvature 10 bit Support Video Picture Engine SUHD Remastering Engine...
Page 68
Mobile to TV - Mirroring, DLNA Family Square with S-Cloud Together Play Easy Setup Samsung SMART View App Casting Wireless TV On - Samsung WOL Wired TV On - Samsung WOL Bluetooth Low Energy Briefing On TV WiDi WiFi Direct...
Page 69
Anynet+ (HDMI-CEC) Design Design Triumph-Flat Bezel Type Bezel-less Slim Type Premium Slim Front Color Silver Light Effect (Deco) Yes (Samsung Badge Lighting) Stand Type Branch Shape (Silver) Swivel (Left/Right) Additional Feature Samsung 3D Instant On Processor Quad-Core SCSA Support Accessibility...
Page 70
2. Product specifications Item UN65KS8000FXZA Additional Feature Smart Evolution Support Teletext (TTX) Time Shift V-Chip MBR Support Ultra Clean View Eco Feature Energy Star Eco Sensor Energy Efficiency Class Power Power Supply AC110-120V 50/60Hz Power Consumption (Max) 220 W Power Consumption (Stand-by) 0.3 W Power Consumption (Typical) 70 W...
Page 74
Pairing the TV to the Samsung Smart Control When you turn on the TV for the first time, the Samsung Smart Control pairs to the TV automatically. If the Samsung Smart Control does not pair to the TV automatically, point it at the remote control sensor of the TV, and then press and hold the buttons labeled 1 and 2 in the figure on the left simultaneously for 3 seconds or more.
Page 76
2. Product specifications 2-5-3. EXTRA Key 2-23...
Page 77
2. Product specifications 2-6. HDMI Color 2-6-1. HDMI UHD Color • When you set the HDMI connection to On, the TV turns off and then on automatically. • The HDMI connection with HDMI UHD Color set to Off supports up to UHD 50P/60P 4:2:0 input signals, while the HDMI connection with HDMI UHD Color set to On supports up to UHD 50P/60P 4:4:4 and 4:2:2 input signals.
Page 78
2. Product specifications 2-7. Supported Formats 2-7-1. Supported image formats and resolutions File Extension Type Resolution *.jpg JPEG 15360x8640 *.jpeg *.png 4096x4096 *.bmp 4096x4096 *.mpo 15360x8640 2-7-2. Supported music formats and codecs File Extension Type Codec Note *.mp3 MPEG MPEG1 Audio Layer 3 *.m4a *.mpa MPEG4...
Page 79
2. Product specifications 2-7-3. Supported video codecs File Frame rate Bit rate Container Video Codecs Resolution Audio Codec Formats (fps) (Mbps) 4096 x 2160: 30 H.264 BP/MP/HP 3840 x 2160: 60 4096 x 2160 HEVC (H.265 - Main, Main10, Main4:2:2 10) Motion JPEG 3584 x 2160 *.avi...
Page 80
2. Product specifications 2-8. Accessories NOTE • The items’ colors and shapes may vary depending on the model. • Cables not included in the package contents can be purchased separately. • The part code for some accessories may differ depending on your region. Product Code.
Page 81
3. Disassembly and Reassemble 3. Disassembly and Reassembly Disconnect the LED TV from the power source before disassembly. Follow these directions carefully. Use the Samsung Service tool to disassemble the cabinet. • Recommend to use the Samsung Service tool. CAUTION Recommended Torque for Cabinet/Stand screws : 10 ~ 12kgf •...
Page 82
3. Disassembly and Reassemble Description Picture Description Screws Insert the Open Jig tool into left bottom side of the rear cover and following directions → → Open Jig If you cannot open, find the locking point HOOK disassembling Press Gently lift up the Rear Cover from the bottom corners to release all mounting clips as indicated by Red Rectangles .
Page 83
3. Disassembly and Reassemble Description Picture Description Screws Remove the BT/WIFI module from the speaker. Remove the BT/WIFI and speaker Cables from the main board then remove the speaker. Remove the power cable, BLU cable and Power cable the USI-T cables. BLU cable USI-T cables Disconnect the function cable from the...
Page 84
3. Disassembly and Reassemble Description Picture Description Screws Removing SMPS - Remove 2EA Screws on SMPS Board.
Page 85
3. Disassembly and Reassemble Description Picture Description Screws Removing SMPS board. • Gently lift up (Bottom Left corner) to release the lock • Use both hands to hold the board and slide to the right to release Lift out (Bottom Left corner) to release the lock CAUTION When installing the SMPS board, verify the board is properly positioned in all 6...
Page 86
3. Disassembly and Reassemble Description Picture Description Screws Removing Main board. • Gently lift up (Top Right corner) to release the lock • Use both hands to hold the board and slide to the left to release the board. Lift out (Top Right corner) to release the lock CAUTION When installing the Main board, verify the board is properly positioned in all 4...
Page 87
4. Troubleshooting 4. Troubleshooting 4-1. Previous Check Check list for initial operation Check the various cable connections first. Check to see if there is a burnt or damaged cable. Check to see if there is a disconnected or loose cable connection. Check to see if the cables are connected according to the connection diagram.
Page 88
4. Troubleshooting 4-2. How to Check Fault Symptom 4-2-1. Power TV POWER STANDBY TV in Standby √ Standby LED Indicator If Not Lit: √ AC 120Vac Line If missing: √ 120Vac Source and Power Cord If OK: √ Resistance on SMPS Fuse after first removing AC power cord.
Page 89
4. Troubleshooting FUNCTION/IR Control CN910 (FUNCTION/IR) IR 3.3Vdc to 2.5Vdc (Effective DC) A3.3V_PW AMP_SCL_I2C 3.3Vdc (effective DC) AMP_SDA_I2C 3.3 Vdc (effective DC) KEY_INPUT1 1.8dc to 0V with command KEY_INPUT2 0V (no operation change) LED_STB_OUT 1.7Vdc STBY A3.3V_PW 3.3V to Deco Lamp LED_CTRL to Deco Lamp 1Vdc (off) 0.5V (On) CN910 LED Status / Function Switch...
Page 90
4. Troubleshooting SMPS POWER Power TV On. PS_ON . 2Vdc (when off) changes to 3.3Vdc (on) √ May already be On if IoT USB is loaded or TV Smart Things Hub mode is active. if voltage error or no change. √...
Page 92
4. Troubleshooting BACKLIGHTS Activate Backlights Test Disconnect Lead Cable from Main Board to Power Supply. √ TV Screen for active backlight LEDs. If NO BACKLIGHTS √ Minus (Control) & Plus pins (Supply) on the Panel Connector voltages to the Panel. If no pin voltages replace SMPS.
Page 93
4. Troubleshooting 4-2-2. Video Customer Picture Test MAIN/TCON BOARD Main Section Pre- FRC (T-CON) Post FRC ( T-CON) Test Result Problem Check Signal Source and other Pass Pass Pass inputs to One Connect Fail Pass Pass Replace Main/T-CON Board Fail Fail Pass...
Page 94
4. Troubleshooting ONE CONNECT MINI <ONE CONNECT MINI> <Disconnect Banner> <Connect Cable> If No Video Disconnect OCB Cable. √ "Disconnect Banner" Displayed. If Banner Appears. √ One Connect Box / Cable (defective). If No Banner continue.
Page 95
4. Troubleshooting MAIN / T-CON Board Main Board Section Start Up Logo Customer Picture Test 1 Mute - 147 - Mute Video Operation : Generated on Main Section. If OK: √ Source & Input Cables. √ Other inputs. √ One Connect Cable/Box.
Page 96
4. Troubleshooting T-CON Section Mute - 369 - Mute NOTE May not be available for Larger models over 70 inches. Video Operation : Generated at T-CON Section. If OK: √ Main / T-CON Board (defective). If Noisy: √ Main / T-CON Board. 4-10...
Page 98
4. Troubleshooting 4-2-3. Audio AUDIO Source • No TV Sound √ Menu → Audio → Speaker Settings set to TV Speaker • Noisy / Distorted TV Audio √ Customer Menu → Support → Sound Test • Sound Test FAILS : (Missing / Noisy Audio) √...
Page 99
4. Troubleshooting 4-2-4. Network <TV> <Router> <Internet> TV to Router "Failure" Check Router Network Status Internet Wired & Wireless MAC Address • in Customer Support Menu. √ No Wired MAC Address : Replace Main Board. √ No Wireless MAC Address : Module cabling &...
Page 100
Terms of Agreement are accepted. Samsung Apps • If it Fails: √ Reset Smart Hub. √ Samsung Apps load correctly. √ Perform " Apps Reset" in Factory Mode. √ Go to Smart Hub and complete Terms of Agreement and set up information.
Page 101
4. Troubleshooting For Netflix Operation/Connection Issues: • Check Certificate & Netflix ESN Status in Factory Mode. If Certificate and ESN exists, " CO", "NfO", change the 8.8.8.8 If Certificate is missing, " C/" replace the TV’s Main Board. If ESN number is missing: NF/ do not replace the Main Board.
Page 102
(DM) 4V p-p 4V p-p 0.5V p-p 0.5V p-p Go to Menu Support Contact Samsung Contact Samsung < - Wired MAC Address : xx:xx:xx:xx:xx:xx Main Board. Missing or Error : Replace - Wireless MAC Address : xx:xx:xx:xx:xx:xx - Bluetooth Address : xx:xx:xx:xx:xx:xx •...
Page 103
4. Troubleshooting 4-3. Factory Mode Factory Remote Power TV ON. Select TV Source. Info → Factory. MENU for return. Samsung IR Remote (Limited Operation) TV Power Standby. Press as follows. • Remote Button : MUTE Power • Option (must set Option Bytes when replacing Main Board.)
Page 104
4. Troubleshooting Option Factory Reset Type --A1MU0QK Local Set SW Model UKS7000 Model 8000 TUNER S_T2C Table NONE MRT Option Engineer Option Setting Option Bytes Enter Factory Mode with Service Remote (only) Check Option Byte Table located on GSPN (Fast Track or Tips) Select each item to change Soft power TV Off to load →...
Page 105
4. Troubleshooting → Info → ER Count • WD Count : Watch Dog (Hardware related issue). AR Count • : Auto Reset (software (i.e. Apps) related. important Error Count Status Screen. • Verify each item listed. 4-19...
Page 106
4. Troubleshooting Factory Mode → Control → EDID Remove ALL HDMI connections. Factory Mode → Control → EDID. (→ Enter Key) Option EDID Control Sub Option Debug Hotel Option Shop Option ADC/WB Asia Option Advanced Sound Select EDID/OFF to ON. (→ Right Arrow Key) EDID ON/OFF Enter Key)
Page 107
4. Troubleshooting 4-4. Factory Mode Adjustments 4-4-1. Detail Factory Option NOTE If you replace the main board with new one, please change the factory option as well. The options you must change are "Type". UN49KS8000FXZA 49" Inches FA01 Vendor PANEL Code BN95-02608A...
Page 108
4. Troubleshooting UN55KS8000FXZA 55" Inches FA01 Vendor PANEL Code BN95-02609A Spec. CY-QK055FLLV2V/H Vendor SOLUM SMPS BOARD Code BN44-00878A Spec. L55E7_KSM Chassis Ass'y BN91-17212A MAIN BOARD PBA Ass'y BN94-10751A, BN94-10924A Byte Item Factory Reset Type 55A1MU0QK Local set SW Model UKS7000 BOM Model 8000...
Page 109
4. Troubleshooting UN60KS8000FXZA 60" Inches EA01 Vendor SHARP PANEL Code BN95-02642A Spec. CY-QK060FLSV1V/H Vendor SOLUM SMPS BOARD Code BN44-00880A Spec. L65E8N_KSM Chassis Ass'y BN91-17218B MAIN BOARD PBA Ass'y BN94-10757B, BN94-10924A Byte Item Factory Reset Type 60H1MU0QK Local set SW Model UKS7000 BOM Model 8000...
Page 111
4. Troubleshooting 4-4-2. Factory Data Option Factory Menu Name Data Range Factory Reset Type 49" 49A1MU0QK 55" 55A1MU0QK 60" 60H1MU0QK 65" 65A1MU0QK, 65L1MU0QK Local Set SW Model UKS7000 BOM Model 8000 TUNER Ch Table NONE MRT Option Control Factory Menu Name Data Range...
Page 112
4. Troubleshooting Factory Menu Name Data Range Visual Test Diable OPTION_SWU RF Remocon Support CDD mode … DPMS Support T-CON Device JazzFT RM Server Type Operating LMF LEAVE THRESHOLD LMF TRIM THRESHOLD LMF TERM THRESHOLD EOS Click BP PMS Reset FAnet Thread CI CPLD Version ACM_MC...
Page 113
4. Troubleshooting Factory Menu Name Data Range Operation Music Mode External Source Eco Solution Cloning Shop Option Exhibition Mode Peak Mode Metadata Shopmode Picture Reset Asia Option Unbalance AF Level adjust TX Power Level Mono Last Memory H Shaking SOUND High Devi *If the broadcast signal is not good, TV will complement the characteristics of the signal (most...
Page 114
4. Troubleshooting Factory Menu Name Data Range PEQ Test Ready Speaker EQ Bottom Checksum NONE Wall Filter Type SRS Tuning Parm SPDIF PCM Gain AudioDock BT Delay 3D_Glass BT delay Mic Scale India Sound Speaker Delay Normal NTV CU Delay NORMAL Lipsync Inx Lipsync Checksum...
Page 115
4. Troubleshooting Factory Menu Name Data Range AP Vx1 SSC ON/OFF AP Vx1 Value N Vx1 SSC ON/OFF N Vx1 Value FRC Vx1 SSC ON/OFF FRC Vx1 SSC Period FRC Vx1 SSC Modulation FRC LVDS ON/OFF FRC LVDS SSC MFR FRC LVDS SSC MRR FRC DDR SSC ON/OFF FRC DDR SSC Period...
Page 116
4. Troubleshooting Factory Menu Name Data Range Netflix OSD Threshold TCON TCON_TEMP READ TEMP LAST 6000 DCC VERSION TCON Demura Bypass TCON FDisplay Panel Code 1 Panel Code 2 Panel Revision Panel Menu Week Panel S/N 1 Panel S/N 2 Panel S/N 3 Panel S/N 4 MPEG Margin...
Page 117
4. Troubleshooting Factory Menu Name Data Range CES ATSC 3_0 CES OOBE MVPD SUPPORT BT DUT BT Throughput Failure Reproduce Module 21_9 L-DETECT STABLE TIME L-DETECT UNSTABLE TIME L-DETECT CAPTION THRESHOLD L-DETECT RAGION THRESHOLD L-DETECT B-LEVEL THRESHOLD L-DETECT USB SUPPORT DB Download MRT Option Dump Failure...
Page 118
4. Troubleshooting Factory Menu Name Data Range HDMI FLT CNT SIG HDMI FLT CND SIG2 HDMI FLT CNT LOS UNSTABLE BAN CNT 1250ms HDMI ROBIN HDMI Callback HDMI CTS Thld HDMI CTS Cnt1 HDMI EQ HDMI Write Type HDMI Switch DVI SET TIME H Write HDMI Sync...
Page 119
4. Troubleshooting Factory Menu Name Data Range Test Pattern Scaler Pattern US Post Pattern FRC Pre Pattern FRC Post Pattern SOC TCON Pattern SOC TCON Pattern Level FRC OSD Pre Pattern FRC OSD Post Pattern FRC2 Pre Pattern FRC2 Post Pattern SOC TCON2 Pattern SOC TCON2 Pattern Level Upgrade...
Page 120
4. Troubleshooting Factory Menu Name Data Range NTV CU UPDATE UD LDC PROFILE UPGRADE Pic Data USB Update Audio Data USB Update Eco Data USB Update CI CPLD Upgrade SC ADK Upgrade Other Setting Delete S/N IPERF Stopped Expert CAL Data Backup …...
Page 121
4. Troubleshooting Factory Menu Name Data Range PC Calibration HDMI Calibration ADC Result 1st_Y_GH 1st_Y_GL 1st_Cb_BH 1st_Cb_BL 1st_Cr_RH 1st_Cr_RL 2nd_R_L 2nd_G_L 2nd_B_L 2nd_R_H 2nd_G_H 2nd_B_H White Balance R-Offset G-Offset B-Offset R-Gain G-Gain B-Gain WB-W2_R_Offset WB_W2_B_Offset WB_W2_R_Gain WB_W2_B_Gain WB_N_R_Offset WB_N_B_Offset WB_N_R_Gain WB_N_B_Gain MGA On/Off R1_Gain...
Page 122
4. Troubleshooting Factory Menu Name Data Range B2_Gain R3_Gain G3_Gain B3_Gain R4_Gain G4_Gain B4_Gain R5_Gain G5_Gain B5_Gain R6_Gain G6_Gain B6_Gain R7_Gain G7_Gain B7_Gain R8_Gain G8_Gain B8_Gain R9_Gain G9_Gain B9_Gain R10_Gain G10_Gain B10_Gain SPI White Balance SPI White Balance On/Off SPI R-Offset SPI G-Offset SPI B-Offset SPI R-Gain...
Page 123
4. Troubleshooting Factory Menu Name Data Range SPI W2 Rgain SPI W2 Bgain SPI W2 Roffset SPI W2 Boffset SPI MGA WB Data to SPI Advanced 4-37...
Page 124
4. Troubleshooting 4-5. RS-232C 4-5-1. RS232C Control • Port : COM#(Serial) • Baud rate : 9600 • Data Bit : 8 bit • Parity : None • Stop Bits : 1 Flow Control : None Description of RS232C Pin# Name Full Name Pin# Name Full Name...
Page 125
4. Troubleshooting 4-6. AV Control Tabe Control Item Cmd1 Cmd2 Cmd3 Value General Power Power 0x00 0x00 0x00 0x00 0x01 0x02 Volume Direct 0x01 0x00 0x00 (0~100) 0x01 0x00 Down 0x02 0x00 Mute 0x02 0x00 0x00 0x00 Direct 0x04 Continuous 0x03 0x00 0x01...
Page 126
4. Troubleshooting Control Item Cmd1 Cmd2 Cmd3 Value Relax 0x07 PICTURE BackLight(CellLight) 0~20 0x01 0x00 (0~20) Contrast 0~100 0x02 0x00 (0~100) Brightness 0~100 0x03 0x00 (0~100) Sharpness 0~100 0x04 0x00 (0~100) Color 0~10 0x05 0x00 (0~100) Tint 0x06 0x00 (0~100) Advanced Settings Black Tone 0x07...
Page 127
4. Troubleshooting Control Item Cmd1 Cmd2 Cmd3 Value Yellow 0x03 PICTURE Advanced Settings Color Space Custom Cyan 0x04 Color Magenta 0x05 Color Space Custom 0~100 0x13 0~100 Color Red Value Color Space Custom 0~100 0x14 0~100 Color Green Value Color Space Custom 0~100 0x15 0~100...
Page 128
4. Troubleshooting Control Item Cmd1 Cmd2 Cmd3 Value Film Mode 0x05 0x00 PICTURE Picture Option Film Mode Auto1 0x01 Auto2 0x02 Cinema 0x03 Smooth Auto Motion Plus 0x06 0x00 Clear 0x01 Standard 0x02 Smooth 0x03 Custom 0x04 Blur Reduction 0x07 value Judder Reduction 0x08...
Page 129
4. Troubleshooting Control Item Cmd1 Cmd2 Cmd3 Value Reset Picture Reset Picture 0x0d 0x0b 0x00 0x00 PICTURE 3D Mode 0x0e 0x0c 0x00 0x00 2D->3D 0x01 Side By Side 0x02 Top Bottom 0x03 Line By Line 0x04 Vertical Line 0x05 Checker BD 0x06 Frame 0x07...
Page 130
4. Troubleshooting Control Item Cmd1 Cmd2 Cmd3 Value Size2 0x01 PICTURE Size Size3 0x02 Size4 0x03 Position Position1 0x04 0x00 Position2 0x01 Position3 0x02 Position4 0x03 Sound Select Main 0x05 0x00 0x01 Picture Off 0x12 0x00 0x00 0x00 Sound Sound Mode Standard 0x0c 0x00...
Page 131
4. Troubleshooting Control Item Cmd1 Cmd2 Cmd3 Value External Speaker 0x01 Sound Speaker Select Audio Out 0x01 Sound Select Main 0x08 0x00 0x00 0x01 Sound Reset Sound Reset 0x09 0x00 0x00 3D Audio 0x0a 0x00 0x00 0x01 Medium 0x02 High 0x03 Auto Stereo Manual...
Page 132
4. Troubleshooting Control Item Cmd1 Cmd2 Cmd3 Value Mute (On/Off) 0xf0 0x02 0x00 0x00 Channel Number 0xf0 0x03 0x00 0x00 Source (TV/AV/…/HDMI/…) 0xf0 0x04 0x00 0x00 Status Picture Size 0xf0 0x05 0x00 0x00 3D (On/Off) 0xf0 0x06 0x00 0x00 Picture Mode 0xf0 0x07 0x00...
Page 133
Updating from the Internet requires an active Internet connection. • To update using a USB flash drive, download the update package from Samsung.com to your computer. Then, save the update package in the USB device's top-level folder. Otherwise, the TV will not be able to locate the update package.
Need help?
Do you have a question about the UN KS8000F Series and is the answer not in the manual?
Questions and answers