Table of Contents
Advertisement
Manual Timer Programming
You can program this unit to timer-record as many as 8 programs.
If you do not know the PlusCode number for the program you wish
to record, use the following procedure to set your unit to timer-
record the program.
Make sure that the unit's built-in clock is set properly.
Turn on the unit.
Turn on the TV and select the video channel (or AV mode).
Slide the TV/CABLE/DBS/DVD switch to DVD.
VHS TIMER
VHS
ENTER
REC MODE
1
Load a cassette with the record safety tab intact.
2
Press VHS so that the VHS lamp lights up on the unit.
3
Press PROGRAM to access the Program screen.
4
Press rt to select "PROGRAM/
CONFIRM", then press ENTER
access the Program Check screen.
5
Press rt to select the blank
number, then press ENTER. The
program screen appears.
6
Press w e to select "START",
then press rt to set the desired
start time.
Each press of
increases/
rt
decreases the start time in 1-minute
interval.
To increase/decrease the start time in
30-minutes interval, press and hold
.
rt
CABLE/DBS
TV
DVD
0-9
PROGRAM
rtwe
PROGRAM
VCR PLUS+ PRGM
PROGRAM / CONFIRM
R,T THEN (ENTER)
(PROGRAM) TO END
PR START
STOP
CH
DATE
1
8:00P
10:00
12
12/24
2 10:00A
10:45
40
12/25
3
11:30P
1:00 125
12/25
4
5
6
7
8
(PROGRAM) TO END
PROGRAM 4
START
STOP
– –:– –AM
– –:– –AM
DATE
CH SP/EP
– –/– –/– –
– – –
SP
PRESS (RTYU, 8=DAILY
9=WEEKLY), THEN (ENTER)
(PROGRAM) TO END
TIMER RECORDING ON VHS DECK
7
Press w e to select "STOP", then press rt to set the desired
stop time.
Each press of
increases/decreases the stop time in 1-minute
rt
interval.
To increase/decrease the stop time in 30-minutes interval, press and
hold
.
rt
8
Press w e to select "DATE", then press rt to set the desired
date.
The current date appears on the TV screen. The date you enter
appears in its place.
9
Press w e to select "CH", then press rt to select the desired
channel.
10
Press REC MODE to select the desired recording mode. Or
press w e to select "SP/EP", then press rt to select the desired
recording mode.
11
Press ENTER to access the Program Check screen.
12
Press PROGRAM to complete timer programming.
"PROGRAM COMPLETED" appears on the TV screen for about 5
seconds, then the normal screen appears. If "PROGRAM NOT
COMPLETED PROGRAM OVERLAP" appears on the TV screen,
see page 62.
To program another timer, repeat steps 3 - 12.
13
Press VHS TIMER to engage the unit's timer mode. The VHS
recording lamp lights up on the unit and the HDD or DVD deck is
automatically selected. When the HDD or DVD deck is in timer
standby mode, the unit is automatically turned off.
To disengage the timer mode, press VHS TIMER again.
NOTES:
To Timer-Record Weekly Or Daily Serials:
anytime during steps 8 through 10, press number key "9" for
—
weekly serials or number key "8" for daily serials (Monday - Friday).
Either "WEEKLY" or "DAILY" appears on the TV screen. Pressing the
button again makes the corresponding indication disappear.
You can program this unit to timer-record as many as 8 programs. If
you try to program the unit to record a ninth, "PROGRAM FULL"
appears on the TV screen. To record the extra program, you must
first cancel any unnecessary programs. (
In case of a power failure after programming, the unit
backup keeps your selections for approximately 5 seconds.
Programs that start after midnight must have the next day
To record the programs received by cable box or DBS receiver,
record on the HDD or the DVD discs. For details, refer to "Manual
Timer Programming" (
pg. 57).
61
EN
pg. 62)
'
s memory
'
s date.
Hide quick links:
Advertisement
Table of Contents
