DT-V24L1D DT-V24L1 DT-V20L1D DT-V20L1 MULTI FORMAT LCD MONITOR The illustration of the monitor is of DT-V24L1D. INSTRUCTIONS Table of Contents Safety Precautions ... 2 IMPORTANT SAFEGUARDS ... 2 Maintenance ... 3 Installation ... 4 Using the monitor on the stand ... 4 Installing the monitor in the rack ...
U.S.A. only FCC NOTICE CAUTION: Changes or modifications not approved by JVC could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
European Union. national legislation. (Business users) If you wish to dispose of this product, please visit our web page www.jvc-europe.com to obtain information about the take-back of the product. [Other Countries outside the European Union] If you wish to dispose of this product, please do so in accordance with applicable national legislation or other rules in your country for the treatment of old electrical and electronic equipment.
• Do not hold the LCD panel when installing the monitor. • Make sure to install the monitor securely to prevent the monitor from falling over, which causes damage to the monitor or injury. 7 Using the monitor on the stand You can place the monitor in the following two ways when using the monitor on the supplied stand.
Screw holes (See page 18 for the specifications of the screw holes.) 7 Installing the monitor in the rack Use a JVC’s RACK MOUNT ADAPTER (RK-C20L1; not supplied). CAUTION • Detach the stand first. • Ask your dealer to install.
Green screen Lights in Green : The monitor is on. Lights in orange : The monitor is off (standby). Flashes in orange : The monitor is in the suspend mode. Standby button Turns on and off (standby) the monitor. NOTE To disconnect the mains line completely, unplug the AC plug from the wall outlet.
Page 7
☞ “ SYNC FUNCTION” on page 11 Source name entered in “CHARACTER SET.” ☞ “INFORMATION” on page 13 • Displayed when “MONITOR NAME” is set to “ON” (☞ “INFORMATION” on page 13). • Displayed in large letters when “STATUS DISPLAY” is set to “OFF” or “AUTO” (☞...
(cont.) CAUTION It is recommended not to use the power cord holder when installing the monitor in a monitor rack etc. where you cannot easily pull out the AC power cord from an AC outlet. Attaching the Power Cord Holder •...
Note for analog component/analog RGB signals √ √ √ √ The monitor is compatible with G on sync, Y on sync and composite sync (Cs) signals. The monitor is not √ — compatible with separate sync (HS/VS) signals. √ —...
Setting value: AUTO, COMPO. (component), RGB Selects the signal type you want to use for DVI-D (HDCP) terminal. NOTE • DVI-D input of the monitor is compatible with HDCP. • Select “COMPO.” or “RGB” when the signal is not recognized correctly with “AUTO.” COMPO./RGB SEL.
Page 11
Operation guide Shows the buttons for each operation. NOTE • The menu automatically disappears in about 30 seconds after the last menu operation. • Some items may not appear on the menu depending on the input or the input signal. These items are not available. Technical information Setting of “sub menu POSI.”...
Menu Configuration —SET-UP MENU For the operation procedure, see page 7. Operation guide Shows the buttons for each operation. NOTE • The menu automatically disappears in about 30 seconds after the last menu operation. • Some items may not appear on the menu depending on the input or the input signal.
Page 13
Display the total hours of use (unit: hour). You can reset this HOUR METER. Display the model name of the monitor. Display the version of the monitor. Display the total hours of use (unit: hour). This item is used for maintenance of the monitor. You cannot reset this HOUR METER. button while pressing button) and turning “CONTROL LOCK”...
RS485 communication RS-232C RS232C On the monitor connected to the personal computer etc, select the terminal the equipment actually connected to. On the other monitors, select “RS485.” NOTE • Control priority is as follows. MAKE > TRIGGER, serial communication, and buttons on the monitor •...
Operation Set “PARA REMO SEL” of “REMOTE SETTING” to “MAKE” or “TRIGGER” in the set-up menu. Short-circuit the 7th pin terminal (external control) to the 8th pin terminal (GND) so that the monitor can be controlled by the external control.
NOTE • If you turn on the monitor soon after turning it off (standby) (or after a short-term power failure), or plug in the AC power cord soon after unplugging it, the INPUT SELECT lamps may flash, and no image may be displayed.
AC power cord x 1, Power cord holder x 1, Screw x 2 (for power cord holder) Notice on transportation This monitor is precision equipment and needs dedicated packing material for transportation. Never use any packing material supplied from sources other than JVC or JVC-authorized dealers. Options (not supplied) RACK MOUNT ADAPTER (DT-V20L1D and DT-V20L1 only):...
51 (2 243 (9 <Rear view> VESA mounting holes (Size: M4, depth: 10 mm) The illustrations of the monitor are of DT-V24L1D. <Rear view> VESA mounting holes (Size: M4, depth: 10 mm) The illustrations of the monitor are of DT-V20L1D.