Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Stabila LAX 600 Series
Summary of Contents for Stabila LAX 600 Series
- Page 1 3x 360° LINES How true pro's measure LAX 600 series Operating instructions...
-
Page 2: Table Of Contents
LAX 600 series Contents Section Page • 1. Intended use • 2.1 Safety instructions for laser units • 2.2 Safety instructions for the Li-ion battery pack • 3. Unit components • 4. Commissioning • 4.1 Inserting and charging the battery • 4.2 Switching the unit on •... -
Page 3: Intended Use
Congratulations on the purchase of your STABILA measuring tool. LASER STABILA laser units from the LAX 600 series are simple to operate laser lines with three LASER RADIATION 360° laser lines for levelling in a horizontal and vertical direction, for transferring/creating DO NOT STARE INTO BEAM 510 - 635 nm / <1mW... -
Page 4: Unit Components
LAX 600 series 3. Unit components 1. Exit window horizontal 360° laser line 2. Exit window vertical 360° laser lines 3. Sliding switch: ON/OFF switch with transport lock 4. Button: Horizontal laser line 5. Button: Manual mode ON/OFF 6. Button: Vertical laser line 7. Green/red LED: Operating status ON/OFF, battery 8. -
Page 5: Commissioning
LAX 600 series 4. Commissioning 4.1 Inserting and charging the battery Only 12 V Li-ion CAS System (Cordless Alliance System) battery packs can be used. 12 V Li-Power 2.0 Ah Push in the battery pack in the direction of the arrow 12 V Li-Power 4.0 Ah (optional) until it engages. -
Page 6: Switching The Unit On
LAX 600 series 4.2 Switching the unit on Move the laser unit to the working position and switch on using the sliding switch. The LAX 600 / LAX 600 G always starts in horizontal mode and levels itself automatically. The green LED indicates that the unit is switched on. The laser beam flashes if the inclination Always use the centre of the laser unit is too steep. -
Page 7: Functions
LAX 600 series 5. Functions 5.1 Selecting laser functions Once the unit has been switched on using the sliding switch, the "Laser lines" button can be used to set the various laser functions, as required. To indicate that the unit is switched on and the transport lock is open, it is not possible to switch off all of the laser lines at the same time via the "Laser lines"... -
Page 8: Led Indicators
Operation without levelling function Operation activated Battery check failed Replace the battery pack Operation activated Operation with levelling function Get in touch with STABILA Battery capacity low CAS battery Operation with levelling function charge capacity too low Laser in pulse mode -->... -
Page 9: Using The Swb10 Bracket
LAX 600 series 7. Using the SWB10 bracket The LAX 600 / LAX 600G can be attached and aligned on walls or profiles using the SWB10 bracket. The clamp can be used to attach the bracket to interior construction profiles. The hanging hole enables it to be hung on nails or hooks. -
Page 10: Checking The Accuracy
LAX 600 series 8. Checking the accuracy The LAX 600 / LAX 600G is designed for use on building > 2 m sites and is perfectly adjusted before leaving our premises. As with all precision instruments, check > 7 f t the calibration accuracy of the unit on a regular basis. 9 0 °... -
Page 11: Horizontal Check
LAX 600 series 8.2 Horizontal check Checking the horizontal laser line level Please ensure that you adhere as closely as possible to the orientation of the unit as shown. 1. Place the LAX 600 / LAX 600G on a horizontal surface or on a tripod at distance S of at least 5 m (16’5”) in front of a wall, with the operator panel facing towards the wall. -
Page 12: Angle Check
LAX 600 series 8.3 Angle check Checking the 90° angle 1. Mark point A on the floor at a distance of ≥ 10 m (32'10") in a sufficiently large corner 16’5” of the room. ≥ 2. Align the LAX 600/LAX 600G with point A using the plumb-line dot. 3. -
Page 13: Technical Data
LAX 600 series 9. Technical data Laser type: LAX 600 Red diode laser, wavelength 635 nm LAX 600 G Green diode laser, wavelength 510–530 nm Power output: < 1 mW, laser class 2 in accordance with IEC 60825-1:2014 Self-levelling range: approx. ± 4° Levelling accuracy*: Laser line: ±0.3 mm/m ± 3/16“ over 50ft centre of laser line 90°...
Need help?
Do you have a question about the LAX 600 Series and is the answer not in the manual?
Questions and answers