DeWalt DW624 Instruction Manual
Plunge cut router/dw625 electronic plunge cut router
Hide thumbs
Also See for DW624:
- Original instructions manual (132 pages) ,
- Manual (96 pages) ,
- Instruction manual (11 pages)
Table of Contents
Advertisement
Quick Links
328521-01/DW624
9/6/01
8:00 AM
INSTRUCTION MANUAL
GUIDE D'UTILISATION
MANUAL DE INSTRUCCIONES
DW624 Plunge Cut Router/DW625 Electronic Plunge Cut Router
DW624 Toupie à course plongeante/DW625 Toupie électronique à course plongeante
DW624 Rebajadora de columnas/DW625 Rebajadora electrónica de columnas
Page 3
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA
DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO
ANTES DE USAR EL PRODUCTO.
Advertisement
Table of Contents
Related Manuals for DeWalt DW624
Summary of Contents for DeWalt DW624
- Page 1 DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO. GUIDE D’UTILISATION MANUAL DE INSTRUCCIONES DW624 Plunge Cut Router/DW625 Electronic Plunge Cut Router DW624 Toupie à course plongeante/DW625 Toupie électronique à course plongeante DW624 Rebajadora de columnas/DW625 Rebajadora electrónica de columnas...
-
Page 2: Important Safety Instructions
Inspect tool cords • CONSIDER WORK AREA ENVIRONMENT. Don’t expose periodically and if damaged have repaired by DeWalt certified power tools to rain. Don’t use power tools in damp or wet service center. Inspect extension cords periodically and locations. -
Page 3: Double Insulation
328521-01/DW624 9/6/01 8:00 AM Page 1 SAVE THESE INSTRUCTIONS one heavy enough to carry the current your product will draw. FOR FUTURE USE. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. The following table shows the... -
Page 4: Specifications
Voltage decrease of more than 10% will cause loss of power and release lever, shown in Figure 2, and let the router rise to its full overheating. All DeWalt tools are factory tested; if this tool does not height. Depress the plunge release lever to lock the tool in place. -
Page 5: Speed Selection Chart
TABLE 1: RECOMMENDATION FOR THE CORRECT CHOICE OF SPEED Material Cutter Diam. Electronic Control Settings Stage 1 Stage 2 Stage 3 Stage 4 Stage 5 Model #DW624/DW625 8,000 rpm 12,000 rpm 16,000 rpm 18,000 rpm 20,000 rpm Hardwood, e.g., oak Small (1/2") –... - Page 6 328521-01/DW624 9/6/01 8:00 AM Page 4 Switch Controls TO SWITCH ON THE MACHINE N O T E : Before operating any of the controls, read this whole N O T E : Always pull the plug on the cord set out of its receptacle s e c t i o n .
- Page 7 328521-01/DW624 9/6/01 8:00 AM Page 5 determine the routing depth. FIG. 2 If none of the provided screws seems close to the desired height PLUNGE each can be adjusted by loosening the hex nut at the bottom and RELEASE then turning the screw either in or out to make it the proper length.
- Page 8 328521-01/DW624 9/6/01 8:00 AM Page 6 FIG. 4 Depth Stop Control Knob shown in Figure 9. FIG. 5 4 . Rotate the turret stop to position the shortest screw under the DEPTH BOTTOM OF depth stop bar. STOP COLLET 5 . Raise the plunge release lever and push the router down until the end of the bit just touches the workpiece.
- Page 9 The hard laminates will quickly dull steel cutters. STOP HAIRLINE CONTROL Your DeWalt certified Service center has a Router Craft Handbook KNOB available at extra cost which covers the use of routers in great detail and shows the various types of bits available.
- Page 10 328521-01/DW624 9/6/01 8:00 AM Page 8 The direction of feed is important in router usage. Be sure the FIG. 12 FIG. 11 cutter is rotating into the stock by moving left to right on outside edges and clockwise on inside cuts.
- Page 11 328521-01/DW624 9/6/01 8:00 AM Page 9 Accessories FIG. 16 If you need assistance in locating any accessory, please contact WALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286 or call 1-800-4-D WALT (1-800-433-9258). CAUTION: The use of any other accessory might be hazardous.