Corporation recognizes environmental protection as a key management tasks, and is doing its utmost to enhance and improve the quality and scope of its environmental activities. In line with this, Toshiba proactively promotes Green Procurement, and seeks to purchase and use products, parts and materials that have low environmental impacts.
Page 1 of 1 LEAD-FREE SOLDER This product is manufactured using lead-free solder as a part of a movement within the consumer products industry at large to be environmentally responsible. Lead-free solder must be used in the servicing and repair of this product. WARNING: This product is manufactured using lead free solder.
SAFETY INSTRUCTION [LCD] ASIA, EU Page 1 of 4 SAFETY INSTRUCTION WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "SAFETY PRECAUTION" AND "PRODUCT SAFETY NOTICE" INSTRUCTIONS BELOW. Safety Precaution WARNING: SERVICING SHOULD NOT BE ATTEMPTED BY ANYONE UNFAMILIAR WITH THE NECESSARY PRECAUTIONS ON THIS RECEIVER. THE FOLLOWING ARE THE NECESSARY PRECAUTIONS TO BE OBSERVED BEFORE SERVICING THIS CHASSIS.
Page 5
SAFETY INSTRUCTION [LCD] ASIA, EU Page 2 of 4 inflammability, voltage resistance, etc. therefore, use only replacement parts that have these same characteristics. Use only the specified parts when the mark is indicated in the circuit diagram or parts list. 7.
Page 6
SAFETY INSTRUCTION [LCD] ASIA, EU Page 3 of 4 Resistance values in orms (Ω). V: Voltmeter or oscilloscope (r.m.s. or peak reading) Input resistance : 1 MΩ Input capacitance : 200 pF Frequency range : 15 Hz to 1 MHz and d.c. respectively Note: Appropriate measures should be taken to obtain the correct value in case of non sinusoidal waveforms.
SAFETY INSTRUCTION [LCD] ASIA, EU Page 4 of 4 Product Safety Notice Many electrical and mechanical parts in this chassis have special safety-related characteristics. These characteristics are often passed unnoticed by a visual inspection and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc.
Handling the LCD Module Page 1 of 4 SAFETY INSTRUCTION Handling the LCD Module Safety Precaution In the event that the screen is damaged or the liquid crystal (fluid) leaks, do not breathe in or drink this fluid. Also, never touch this fluid. Such actions could cause toxicity or skin irritation. If this fluid should enter the mouth, rinse the mouth thoroughly with water.
Page 9
Handling the LCD Module Page 2 of 4 3. If the panel surface becomes soiled, wipe with cotton or a soft cloth. If this does not remove the soiling, breathe on the surface and then wipe again. If the panel surface is extremely solied, use a CRT cleaner as a cleaner. Wipe off the panel surface by drop the cleaner on the cloth.
Page 10
Handling the LCD Module Page 3 of 4 6. CMOS-LSI circuitry is used in the LCD module, so avoid damage due to static electricity. When handling the module, use a wrist ground or anchor ground. 7. Do not expose the LCD module to direct sunlight or strong ultraviolet rays for an extended period of time.
Page 11
Handling the LCD Module Page 4 of 4 10. When transporting the LCD module, do not use packing containing epoxy resin (amine) or silicon resin (alcohol or oxim). The gas generated by these materials can cause loss of polarity.
Page 12
POWER LOWB AV TERM FRONT HDMI SIGNAL 100...
Page 13
Digital receiving board AV BOARD SIGNAL BOARD PANEL DDR RAM DDR RAM FLI8668 CORTEZ Advance VBI Data Processor PANEL I/F DCDi Input Video Analog MADi Terminal Decoder Front Scaling (Audio) (16port) LVDS CVBS(L/R) S-VIDEO(L/R) YCbCr(L/R) Channel SCART(L/R) Standby Process uCON Digital Input A EEPROM...
Page 1 of 2 SCHEMATIC DIAGRAM Precaution WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "X-RAY RADIATION PRECAUTION" FOR DIRECT VIEW CTV ONLY, "SAFETY PRECAUTION" AND "PRODUCT SAFETY NOTICE" OF THIS MANUAL. CAUTION: The international hazard symbols " " in the schematic diagram and the parts list designate components which have special characteristics important for safety and should be replaced only with types identical to those in the original circuit...
Page 15
Page 2 of 2 All capacitors are ceramic 50 V, unless otherwise noted as the following marks. = Electrolytic capacitor = Mylar capacitor 3. The parts indicated with " " have special characteristics, and should be replaced with identical parts only. 4.
Entering to Service Mode 1. Set VOLUME to minimum and press button once on remote control. ↓ 2. Press button again and hold button down. ↓ Service Mode display 3. While holding the button, press MENU button on TV set. file://\\serwer\instr\CD\1000-1099\CD1031\37WL68P-01\37WL68P-01\html\!adj-sm... 2013-12-02...
Page 117
Press ↑ ↓ Press Adjustment Mode Key Function in the Service Mode The following key entry during display of adjustment menu provides special functions. CAUTION: Never try to perform initialization unless you have changed the memory IC. button (on remote control) file://\\serwer\instr\CD\1000-1099\CD1031\37WL68P-01\37WL68P-01\html\!adj-sm... 2013-12-02...
Page 118
[ SERVICE MODE ] ADJUSTING ITEMS AND DATA IN THE SERVICE MODE: Note: The image system data of RCUT-BDRV is different by each image format. The PAL value is indicated in the table. Never adjust H.POS and V.POS except PAL/WIDE mode. file://\\serwer\instr\CD\1000-1099\CD1031\37WL68P-01\37WL68P-01\html\!adj-sm... 2013-12-02...
Page 119
TV SET OPTION 7 (HOTEL MODE) OPT8 TV SET OPTION 8 (HOTEL MODE) TVOP TV SET OPTION MODEL ID BDWID BORDER WIDTH FOR EXACT SCAN BDHIT BORDER HEIGHT FOR EXACT SCAN FPLG MASK_ENABLE (SD/HD) FPLG2 Channel LOGO Vector Clip SW (SD) file://\\serwer\instr\CD\1000-1099\CD1031\37WL68P-01\37WL68P-01\html\!adj-sm... 2013-12-02...
Page 120
After selecting TVOP, press + or - to set I2C check function to disable or enable as below. TVOP FUNCTION DESCRIPTION 0 (Normal) D5 (bit5) I2C check between IC700 and IC400. (WDT) Disable Enable file://\\serwer\instr\CD\1000-1099\CD1031\37WL68P-01\37WL68P-01\html\!adj-sm... 2013-12-02...
Page 121
- to set OPT4 or OPT5 value as table below. Panel option data Series Model name Panel vendor OPT4 value OPT5 value WL68 EU Ready 32WL68P 0x45 0x11 37WL68P 0x46 0x11 EU/UK Digital 32WLT68 0x45 0x11 37WLT68 0x46 0x11 42WLT68...
+ or -., refer to table below. 4) Press and hold the CALL button on the remote control, then press the CHANNEL button on the TV. 5) Initialization progress dialog including model name and panel vender is shown. file://\\serwer\instr\CD\1000-1099\CD1031\37WL68P-01\37WL68P-01\html\!adj-sm... 2013-12-02...
Page 123
9) Check the picture carefully. If necessary, adjust any adjustment item above. Perform "Auto tune" on the ownerfs manual. Europe MODEL ID (HEX) Model name Panel vender 0x01 32WLT68 0x02 37WLT68 0x03 42WLT68 0x04 32WL68P 0x05 37WL68P 0x06 0x07 0x08 0x09 0x10 0x11 0x12 0x13 0x14 0x15 0x16 0x17 0x18 file://\\serwer\instr\CD\1000-1099\CD1031\37WL68P-01\37WL68P-01\html\!adj-sm...
0x26 0x27 0x28 0x29 0x30 0x31 0x32 0x33 Test Signal Selection Every pressing of button on the remote control changes the built-in test patterns on screen as described below in Service Mode. Picture Signal Red raster Green raster file://\\serwer\instr\CD\1000-1099\CD1031\37WL68P-01\37WL68P-01\html\!adj-sm... 2013-12-02...
(1) Firmware : Version information of microprocessor Series name (AAAA) and market area (BB) and software program version (0000) (2) Time : Total hour of turn the TV on. (Unit : H) (3) Bus line : -- "OK" is normal file://\\serwer\instr\CD\1000-1099\CD1031\37WL68P-01\37WL68P-01\html\!adj-sm... 2013-12-02...
Page 126
V1 - V9 : VIDEO 1-9 input mode : PC mode : YUV mode : DTV mode WL68, WLT68 (SCART (FULL)) (SCART (S+AV)) (Composite/Component) HDMI1 HDMI2 HDMI3 Version Check Mode 1. Press "9" button twice on remote control during display of adjustment menu in the file://\\serwer\instr\CD\1000-1099\CD1031\37WL68P-01\37WL68P-01\html\!adj-sm... 2013-12-02...
Page 127
Option information : Display six numbers of 1 byte data. (5) HDMI ID : HDMI ID information : Display 4 byte data. (6) SW Ver Version information of DB software. (Only digital model.) (7) MW Ver Version information of DB software middleware. (Only digital model) file://\\serwer\instr\CD\1000-1099\CD1031\37WL68P-01\37WL68P-01\html\!adj-sm... 2013-12-02...
Page 128
Example : AUO-32 indicates that Vender is AUO and Screen Size is 32 inch Status Check Mode 1. Press "9" button thrice on remote control during display of adjustment menu in the service mode. The status of this model will be checked. 2. During Status Check, the following displays are shown. file://\\serwer\instr\CD\1000-1099\CD1031\37WL68P-01\37WL68P-01\html\!adj-sm... 2013-12-02...
Page 129
(6) SUB PLL : Sub PLL information : Display 1 byte data at five. This item displays only Double window model. (7) SCREEN SIZE : Display the screen size as follows. Exact Scan Wide Super Live 2 Cinema 2 file://\\serwer\instr\CD\1000-1099\CD1031\37WL68P-01\37WL68P-01\html\!adj-sm... 2013-12-02...
Page 130
Enable (Video/TV) D3 (bit3) User remote control operation Disable Enable (Service mode and Supere User mode may possible to setting only) D2 (bit2) Disable SET UP MENU except Disable Enable language. (Display the language only) (tuning SETUP MENU) file://\\serwer\instr\CD\1000-1099\CD1031\37WL68P-01\37WL68P-01\html\!adj-sm... 2013-12-02...
Page 131
Enable mode that speaker volume will be set in Enable Disable forced when turn ON the main power D6 (bit6) ~ Forced speaker volume 0 ~ 100 [decimal] (Normal: 0) D0 (bit0) Value above 100 is no effect. file://\\serwer\instr\CD\1000-1099\CD1031\37WL68P-01\37WL68P-01\html\!adj-sm... 2013-12-02...
ON the TV. 2 Green is OFF; Abnormal operation of Turn OFF the TV and unplug Red blinks continuously at 1- BUS line. the power cord. second intervals. Plug the power cord in again and turn ON the TV. file://\\serwer\instr\CD\1000-1099\CD1031\37WL68P-01\37WL68P-01\html\!adj-sm... 2013-12-02...
Page 133
Page 18 of 18 file://\\serwer\instr\CD\1000-1099\CD1031\37WL68P-01\37WL68P-01\html\!adj-sm... 2013-12-02...
The PC board assembly with mark is no longer available after the end of the production. Abbreviations Capacitors CD : Ceramic Disk Resistors : Carbon film OMF : Oxide Metal Film : Plastic Film : Carbon Composition : Variable Resistor file://\\serwer\instr\CD\1000-1099\CD1031\37WL68P-01\37WL68P-01\html\lst_prec... 2013-12-02...
Page 135
Page 2 of 2 : Electrolytic : Metal Film : Fusible Resistor All CD and PF capacitors are ±5 %, 50 V and all resistor, ±5 %, 1/6 W unless otherwise noted. file://\\serwer\instr\CD\1000-1099\CD1031\37WL68P-01\37WL68P-01\html\lst_prec... 2013-12-02...
Page 136
U02D DB DOWNLOAD (PE0195) Location Parts No. Description U02D 75004441 PC BOARD ASSY, PE0195A4, DB DOWNLOAD CL02 76092883 CAPACITOR, CERAMIC CHIP, 50V B 0.1UF K GR60 76000445 CHIP JUMPER, 1608TYPE GR61 76000445 CHIP JUMPER, 1608TYPE PL05B 23713776 PLUG, 3P 2.5MM W, S3B-EH PL05C 23713759 PLUG, 8P 2.5MM G, B8B-EH-F1-TV4...
Page 137
U03A FRONT HDMI (PE0196) Location Parts No. Description U03A 75004434 PC BOARD ASSY, PE0196A1, FRONT_HDMI C604 76109103 CAPACITOR, CERAMIC CHIP, 50V B 0.01UF K C605 76109103 CAPACITOR, CERAMIC CHIP, 50V B 0.01UF K CC11 76109102 CAPACITOR, CERAMIC CHIP, 50V B 1000PF K CC12 76109102 CAPACITOR, CERAMIC CHIP, 50V B 1000PF K...
Page 171
U02B LED (PE0195) Location Parts No. Description U02B 75004439 PC BOARD ASSY, PE0195A2, LED CB02 76202221 CAPACITOR, ELECTROLYTIC, 10V 220UF M CB03 76100104 CAPACITOR, CERAMIC CHIP, 25V F 0.1UF Z CB04 76100104 CAPACITOR, CERAMIC CHIP, 25V F 0.1UF Z CB05 76202221 CAPACITOR, ELECTROLYTIC, 10V 220UF M DB01...
FUNCTION AND OPERATION The Remote Control Simple at-a-glance reference of your remote control.
Page 174
FUNCTION AND OPERATION Control and Input Connection A wide variety of external equipment can be connected to the input sockets on the side of the television. Whilst all the necessary adjustments and controls for the television are made using the remote control, the buttons on the television may be used for some functions.
Page 177
FUNCTION AND OPERATION Tuning the Television Using Quick Setup, Sorting Programme Position Before switching on the television put your decoder and media recorder to Standby if they are connected. To set up the television use the buttons on the remote control.
FUNCTION AND OPERATION Manual Tune The television can be tuned-in manually using Manual tuning. For example: if the television cannot be connected to a media recorder/decoder with a SCART lead or to tune-in a station on another System. Use left and right to move across the screen and select any of these Manual Tune options. Programme : The number to be pressed on the remote control.
Page 185
FUNCTION AND OPERATION Programme Skip Programme Skip...
Page 188
FUNCTION AND OPERATION Auto Tune Using Auto Tuning...
Need help?
Do you have a question about the 37WL68P and is the answer not in the manual?
Questions and answers