Advertisement
Quick Links
Advertisement
Related Manuals for Hollyland Solidcom C1 HUB8S
Summary of Contents for Hollyland Solidcom C1 HUB8S
- Page 1 Hollyland Solidcom C1 HUB8S V1.0.0...
- Page 2 Introduction Thank you for purchasing Hollyland Full-duplex Wireless Intercom System. The Solidcom C1 HUB8S includes eight single-sided remote wireless headsets along with eight rechargeable batteries, a charger, a HUB base with wired headset, and accessories. It is a full-duplex wireless DECT intercom system engineered to provide clear audio and all-day wearing comfort in a true-wireless design with no beltpack required.
-
Page 3: Packing List
Packing List ④ ① ② ③ ⑤ ⑥ ⑧ ⑦ ⑨ Solidcom C1 - HUB8S Headset Intercom Package ①HUB Base ②Remote Headset (with blue nameplate) ③ 3.5mm HUB Headset (with red nameplate) ④ Charging Case ⑥Microphone Cushion ⑦ 12V/2A DC Adapter ⑧Over-ear Cushion ⑨... -
Page 4: Product Interfaces
Product Interfaces ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ⑩ ⑪ ⑫ ⑭ ⑱ ⑲ ⑮ ⑯ ⑰ ⑳ ⑬ HUB Base Interfaces ⑪USB Interface ① HUB Headset Volume Knob ②Display ⑫ANNOUNCE Button - Press and hold the button ③UP Arrow Key... - Page 5 Product Interfaces Headset Interfaces ① Power/Connection Indicator ② Microphone ③ USB Type-C Interface - For firmware upgrade, and headset pairing ④ Battery Compartment ⑤ Volume + Button ⑥ Volume - Button ⑦ A Button - Lights up when joined Group A, turns off when exited Group A; Long press for 5 seconds to pair ⑧ B Button - Lights up when joined Group B, turns off when exited Group B ⑨ Power Button...
- Page 6 Product Interfaces ② ③ ① Charging Case Interfaces ① Charging Indicator ② Charging Contact ③ DC Charging Interface Orange: Charging in progress Green: Fully charged...
- Page 7 Quick Start Guide Set Up HUB Base Install the HUB antennas. Power Up HUB Base Connect the 12V/2A DC Adapter to the HUB base. Press the Power Switch to turn on. Note: The HUB Base can be powered using NP-F battery, V-Mount/G-Mount battery, or DC power supply.
- Page 8 Quick Start Guide Install Headset Battery Step 1: Slide the battery compartment Step 2: Open the cover Step 3: Place the battery into the compartment cover lock and close the battery cover Turn On Headset Note: The indicator light stops flashing and turns to Nameplate static green when the HUB Base and the Power Switch...
- Page 9 Quick Start Guide ① ⑧ ② ⑦ Master ⑥ ⑤ ④ ③ HUB Base Main Display Interfaces ① HUB Base configuration - Master/Slave ⑥Headset status ②HUB Base battery level TALK: Headset is active to hear and talk ③Headset signal strength MUTE: Headset is muted to hear only ④Headset battery level - turns red in low battery LOST: Headset lost connection with HUB Base...
- Page 10 Quick Start Guide Headset Status Indicator ①FLASH GREEN: Headset disconnected ②STATIC GREEN: Headset connection successful ③FLASH RED: Low battery, please change the battery Pairing Operation The HUB Base and Remote Headsets that come in one system package will auto pair up right out of box. Manual pairing is only required when there is a need for adding or changing headset or HUB base to the system.
- Page 11 Quick Start Guide Headset(s) Number Setting via HUB Base When re-pairing and numbering the headset, be sure to turn on all the headsets to avoid selecting duplicate numbers, which may lead to connection failure with other headsets. In case of wrong numbering of a headset, simply connect it to the HUB with the USB cable and operate the pairing and numbering process again.
- Page 12 Quick Start Guide 4 Wire Settings After connecting the two systems with the network cable, configure each HUB Base’s line sequence by entering "4 Wire Settings" and selecting "Line sequence switching". Set the first HUB Base to “Standard mode” and the second HUB Base to “Cross mode”. HUB Display Interfaces Enter “4 Wire”...
- Page 13 Quick Start Guide HUB Settings After connecting the two systems with the network cable, configure each HUB Base’s basic settings as Master or Slave device. Generally, the first system is set as Master Device, and the second one as Slave Device.
- Page 14 Quick Start Guide Group Settings The HUB Base supports A and B grouping settings. You can view the system’s current group setting by entering the Group menu on the HUB. To operate group settings, connect the computer and the HUB via the RJ45 interface using the network cable, and enter the Group settings menu.
- Page 15 Quick Start Guide Open the browser on the computer and visit http://192.168.218.10 to enter the configuration page of the HUB. A & B Group Buttons on Headset(s) After entering Group setting on the HUB, the A and B Buttons on the connected headset will light up. The buttons light status indicates which group the headset has joined.
- Page 16 Parameters Range 350m (1000ft) Line-of-Sight Frequency band: 1.9GHz DECT (varies by country and region) Modulation mode: GFSK Frequency Information Transmit power: <21dBm (125.9mW) (varies by country and region) Receiving sensitivity: <-90dBm ＜35ms Transmission Latency Battery Capacity 700mAh (2.66Wh) Li-Ion battery Remote headset: ≈10h Headset Runtime ≈2.5h...
- Page 17 S u p po r t If you encounter any problems in using the product or need any help, please contact Hollyland Support Team via the following ways: If encounter any problems in using the product or need any help,please follow these...
-
Page 19: Fcc Requirement
FCC Requirement Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference.
Need help?
Do you have a question about the Solidcom C1 HUB8S and is the answer not in the manual?
Questions and answers